ST SPC58NH-DISP Manual de usuario
Introduction
The SPC58NH-DISP discovery board is a standalone hardware platform to evaluate and develop applications with the
SPC58NH92C5, packaged in a FPBGA386 microcontroller at budget price.
This document provides information about the hardware architecture and how to configure the jumpers to enable specific
functions.
SPC58NH-DISP discovery board
UM2697
User manual
UM2697 - Rev 2 - February 2021
For further information contact your local STMicroelectronics sales office.
www.st.com
1SPC58NH-DISP discovery board
The SPC58NH-DISP discovery board is based on the microcontroller SPC58NH92C5, a high performance
e200z4d triple core 32-bit Power Architecture technology CPU, 200 MHz core frequency with 10496 KB on chip
Flash (10240 KB code Flash + 256 KB data Flash) in an FPBGA386 package.
The several peripherals such as DSPI, LIN (LIN and UART), FlexRay, CAN-FD, two independent ethernet ports
(10/100 Mbps and 1 Gbps), make the SPC58NH-DISP an excellent starter kit for the SW designer to quickly
evaluate the microcontroller as well as to develop and to debug applications.
Free ready-to-run application firmware examples are available inside SPC5Studio web page (http//:www.st.com/
spc5studio) to quickly support evaluation and development.
The PCB, the components and all HW parts assembled in this board meet the requirements of the applicable
RoHS directives.
1.1 Interfaces and connectors
• 1 ethernet port 10/100 Mbps
• 1 ethernet port 1 Gbps
• eMMC
• SD card reader
• HyperFlash and HyperRam
• 3 CAN FD ports with transceiver DB9 connector
• 12 CAN port (GPIO level, 2 connectors)
• 4 x I²C connector
• 1 LIN and 1 K-Line with transceivers
• 2 FlexRay channels (a single transceiver is shared with jumpers)
• 2 UART channels with a DB9 and connector 4x0.1”
• USB to UART (with opto-coupler option)
• 1xST33xx connector
• JTAG (header 2x7 0.1” pin)
• RESET push button
• 3 user push buttons
• 4 user LEDs
• 2 trimmers to ADC (fast ADG evaluation)
• LCD TFT display (320 x 240) with touch screen (option)
• 12 V DC power supply (external PSU)
• 40 MHz and 32.768 KHz crystals
UM2697
SPC58NH-DISP discovery board
UM2697 - Rev 2 page 2/18
2Hardware description
2.1 Power supply
Figure 1 shows the PSU block diagram.
Figure 1. PSU block diagram
1.2 V_SW
3.3 V_LR
LD1086D2T50TR 5.0 V_LR
12 V
L5963
3.3 V_SW
The DC input source is 12 V DC: L5963 is used to generate 3.3 V (VDD_HV_xxx), 1.2 V (VDD_LV_xx) and 3.3 V
for ADC section. A linear regulator is used to generate 5 V for ADC.
The LEDs LD2, LD3, LD4, and LD5 are used to check the output of each voltage regulator and 12 V input source.
A resettable fuse (F1) protects the application against the overload or short-circuit.
UM2697
Hardware description
UM2697 - Rev 2 page 3/18
2.2 Microcontroller
2.2.1 JTAG
A standard JTAG connector 14x0.1” is available for programming and debugging.
Figure 2. JTAG
2.2.2 Reset
Figure 3 shows the reset circuit.
Figure 3. Reset
The reset signal level is driven to low level when:
• VDD_HV is lower than a fixed level. This feature is used to monitor the VDD_HV level and then to reset
the microcontroller when the level is out of specification. This feature allows to set the reset only when the
VDD_HV is stable.
• the pushbutton is pressed (manual reset); the reset pulse width is fixed.
UM2697
Microcontroller
UM2697 - Rev 2 page 4/18
2.3 Ethernet 10/100 Mbps
Section 2.3 shows the ethernet 10-100 Mbps communication channel.
Figure 4. Ethernet 10/100 Mbps
JP15 allows configuring the communication in MII or RMII mode.
The current absorption of this section can be estimated by removing SB7 then applying a low impedance current
meter or a current probe.
UM2697
Ethernet 10/100 Mbps
UM2697 - Rev 2 page 5/18
2.4 Ethernet 1 Gbps
The ethernet 1 Gbps section is depicted here below.
Figure 5. Ethernet 1 Gbps
The resistors from R85 to R84, from R88 to R91, from R95 to R98 and from R100 to R103 are used to configure
the device.
With SB9 close and SB8 left open, the 1V2_ETH supply voltage is controlled by an integrated LDO and an
external MOSFET. The user can exclude the LDO regulator and connect the 1V2_ETH to the 1.2 V source form
the PSU section setting SB9 open and SB8 close.
UM2697
Ethernet 1 Gbps
UM2697 - Rev 2 page 6/18
2.5 eMMC and μSD
Figure 6 and Figure 7 are showing the eMMC and µSD card reader section respectively.
From the microcontroller, the signals Data 0÷3, CMD, CLK and FBCLK are shared among these sections and this
means only one section can be active at a time.
These signals must be connected to the active section by selecting the jumpers from JP17 to JP22 properly: see
Figure 8.
Figure 6. eMMC card
Figure 7. μSD card
UM2697
eMMC and μSD
UM2697 - Rev 2 page 7/18
Figure 8. eMMC and μSD jumpers configuration
2.6 Octal SPI
The OctalSPI section is visible in Section 2.6 . In this application the OctalSPI is connected to a HyperFlash and
HyperRAM device.
The microcontroller ports PF[4] and PN[12] are used to drive CS1# and CS2#.
Figure 9. HyperFlash and HyperRAM
UM2697
Octal SPI
UM2697 - Rev 2 page 8/18
2.7 LIN and K-Line
LIN and K-Line channels with the dedicated transceivers are described in the Figure 10.
Figure 10. LIN and K-Line
2.8 Flex Ray
Flex Ray section is reported in Section 2.8 ; JP33, JP34 and JP35 allow selecting which channel from the
microcontroller is connected to the transceiver.
Figure 11. Flex Ray
UM2697
LIN and K-Line
UM2697 - Rev 2 page 9/18
2.9 I²C
Four I²C channels are available. A pull-up resistor is connected to each line and a jumper allows disconnecting it.
Figure 12. I²C
2.10 CAN-FD
Three CAN-FD channels with fast transceivers are connected to DB9 connectors. Further 6 + 6 channels are
connected to 2 connectors without transceivers (GPIO level).
Figure 13. CAN-FD
UM2697
I²C
UM2697 - Rev 2 page 10/18
Tabla de contenidos
Otros manuales de Hardware de computadora de ST
ST
ST UM1472 Manual de usuario
ST
ST PCC020V1 Manual de usuario
ST
ST STM32F3DISCOVERY Manual de usuario
ST
ST X-NUCLEO-IHM09M1 Manual de usuario
ST
ST X-NUCLEO-OUT11A1 Manual de usuario
ST
ST STEVAL-ISF001V1 Manual de usuario
ST
ST STEVAL-CCH002V1 Manual de usuario
ST
ST EVAL6470H-DISC Manual de usuario
ST
ST STEVAL-ETH001V1 Manual de usuario
ST
ST EVSPIN958 Manual de usuario
ST
ST X-NUCLEO-NFC02A1 Manual de usuario
ST
ST STEVAL-MKI015V1 Guía de inicio rápido
ST
ST STEVAL-C34KAT2 Manual de usuario
ST
ST X-CUBE-CELLULAR Manual de usuario
ST
ST STEVAL-IFP044V1 Manual de usuario
ST
ST X-NUCLEO-OUT04A1 Manual de usuario
ST
ST FP-ATR-ASTRA1 Manual de usuario
ST
ST ST8034T Manual de usuario
ST
ST X-NUCLEO-IHM12A1 Manual de usuario
ST
ST X-NUCLEO-OUT17A1 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
