ST X-NUCLEO-IHM14A1 Manual de usuario
Version 1.0 (Oct 18, 2017)
Quick Start Guide
Stepper motor driver expansion board based on STSPIN820 for STM32
Nucleo
(X-NUCLEO-IHM14A1)
Quick Start Guide Contents 2
X-NUCLEO-IHM14A1: Stepper motor driver expansion board
Hardware and Software overview
Setup & Demo Examples
Documents & Related Resources
STM32 Open Development Environment: Overview
Arduino UNO R3 connector
Low voltage stepper motor driver expansion board
Hardware overview 3
X-NUCLEO-IHM14A1 Hardware Description
•The X-NUCLEO-IHM14A1 motor driver expansion
board is based on the STSPIN820 monolithic driver
for stepper motors.
•It represents an affordable, easy-to-use solution for
driving stepper motors in your STM32 Nucleo project,
implementing motor driving applications such as
2D/3D printers, robotics and security cameras.
•The STSPIN820 implements a PWM current control
with constant OFF time adjustable via an external
resistor and a microstepping resolution up to the
256th step.
•The X-NUCLEO-IHM14A1 expansion board is
compatible with the Arduino UNO R3 connector and
the ST morpho connector, so it can be plugged to the
STM32 Nucleo development board and stacked with
additional X-NUCLEO expansion boards.
(*) Not mounted
STSPIN820 ST morpho connector*
Key Products on board
STSPIN820
Advanced 256 microsteps integrated motor driver
with step-clock and direction interface
Supply and motor connector
Latest info available at www.st.com
X-NUCLEO-IHM14A1
Low voltage stepper motor driver expansion board
Software overview 4
X-CUBE-SPN14 Software Description
The X-CUBE-SPN14 expansion package for STM32Cube
gives you full control of stepper motor operations. When
combined with one or more X-NUCLEO-IHM14A1 expansion
boards, this software allows a compatible STM32 Nucleo board
to control one or more stepper motors. It is built on top of
STM32Cube software technology for easy portability across
different STM32 microcontrollers. The software comes with a
sample implementation for one stepper motor. It is compatible
with STM32 NUCLEO-F401RE, NUCLEO-F334R8, NUCLEO-
F030R8 or NUCLEO-L053R8 boards with an X-NUCLEO-
IHM14A1 expansion board mounted on top.
Key features
•A driver layer for complete management of the STSPIN820
(low power stepper motor driver) device integrated in
theXNUCLEOIHM14A1 expansion board
•Device parameter read and write modes, GPIO, PWM and
IRQ configuration, micro-stepping, direction position, speed,
acceleration, deceleration and torque controls; automatic
full-step switch management, high impedance or hold stop
mode selection, enable and stand-by management
•Fault interrupt handling
•Single stepper motor control sample application
•Easy portability across different MCU families, thanks to
STM32Cube
•Free, user-friendly license terms
Latest info available at www.st.com
X-CUBE-SPN14
Overall Software Architecture
Quick Start Guide Contents 5
X-NUCLEO-IHM14A1: Stepper motor driver expansion board
Hardware and Software overview
Setup & Demo Examples
Documents & Related Resources
STM32 Open Development Environment: Overview
NUCLEO-F401RE
NUCLEO-F334R8
NUCLEO-F030R8
NUCLEO-L053R8
Setup & Demo examples
Hardware prerequisites
•1x Stepper motor expansion board
(X-NUCLEO-IHM14A1)
•1x STM32 Nucleo development board
(NUCLEO-F401RE or NUCLEO-F334R8 or NUCLEO-F030R8 or NUCLEO-L053R8)
•1x stepper motor
•1x external DC power supply with two electric cables (*)
•1x Windows 8/7 - Laptop/PC
•1x USB type A to Mini-B USB cable
6
(*) Power stage supply voltage from 7 V to 45 V
Mini USB Cable X-NUCLEO-IHM14A1
Stepper motor
Setup & demo examples
Software prerequisites
•STSW-LINK009: ST-LINK/V2-1 USB driver
•STSW-LINK007: ST-LINK/V2-1 firmware upgrade
•A Windows PC with one of the supported development toolchains:
•KEIL: MDK-ARM
•IAR: EWARM
•GCC-based IDE: System Workbench for STM32
•X-CUBE-SPN14: software expansion for STM32Cube
7
Stepper motor driver expansion board
Start coding in just a few minutes with X-CUBE-SPN14 8
3On the X-NUCLEO-IHM14A1
•Tune VREF potentiometer to adjust the
reference voltage.
Driving one stepper motor with X-NUCLEO-IHM14A1 and X-CUBE-SPN14
1Plug the X-NUCLEO-IHM14A1 on the STM32 Nucleo board using theArduino UNO
R3 connector and connect the stepper motor (A+/- and B+/-) and the power supply
(VIN\GND) to the CN1 connector.
2Connect the STM32 Nucleo board to the PC through the USB cable.
Stepper motor driver expansion board
Start coding in just a few minutes with X-CUBE-SPN14 9
4Depending on your STM32 Nucleo board, from the examples folder
(\stm32_cube\Projects\Multi\Examples\MotionControl\IHM14A1_ExampleFor1Motor)
open the software project from:
•\YourToolChainName\STM32F401RE-Nucleo for Nucleo based on STM32F401
•\YourToolChainName\STM32F334R8-Nucleo for Nucleo based on STM32F334
•\YourToolChainName\STM32F030R8-Nucleo for Nucleo based on STM32F030
•\YourToolChainName\STM32L053R8-Nucleo for Nucleo based on STM32L053
5Open the file:
stm32_cube\Drivers\BSP\Components\STSPIN820\STSPIN820_target_config.h.
and modify the parameters according to your target configuration.
6Build the project and download it into the STM32 memory.
7Run the example. The motor automatically starts (see main.c for a detailed
demo sequence).
Documents & related resources
X-NUCLEO-IHM14A1:
•Gerber files, BOM, and schematics
•DB3416:Stepper motor driver expansion board based on STSPIN820 for STM32 Nucleo–Data
brief
•UM2299: Getting started with the X-NUCLEO-IHM14A1 stepper motor driver expansion board
based on STSPIN820 for STM32 Nucleo –User manual
X-CUBE-SPN14:
•DB3417:Stepper motor driver software expansion for STM32Cube –Data brief
•UM2300: Getting started with X-CUBE-SPN14 stepper motor driver software expansion for
STM32Cube –User manual
•Software setup file
10
All documents are available in the DESIGN tab of the related products webpage
Consult www.st.com for the complete list
Tabla de contenidos
Otros manuales de Hardware de computadora de ST
ST
ST X-NUCLEO-EEPRMA2 Manual de usuario
ST
ST X-NUCLEO-IHM07M1 Manual de usuario
ST
ST STEVAL-IFP045V1 Manual de usuario
ST
ST X-NUCLEO-BNRG2A1 Manual de usuario
ST
ST STR9 Manual de usuario
ST
ST STEVAL-TTM001V1 Manual de usuario
ST
ST STM32 Nucleo Manual de usuario
ST
ST STR9 Manual de usuario
ST
ST X-NUCLEO-OUT11A1 Manual de usuario
ST
ST STM32 Nucleo Manual de usuario
ST
ST X-NUCLEO-IHM09M1 Manual de usuario
ST
ST X-NUCLEO-OUT13A1 Manual de usuario
ST
ST ST7MDTU3-EMU2B Manual de usuario
ST
ST X-NUCLEO-OUT19A1 Manual de usuario
ST
ST X-NUCLEO-IHM02A1 Manual de usuario
ST
ST X-NUCLEO-IDW01M1 Manual de usuario
ST
ST STM8S-DISCOVERY Manual de usuario
ST
ST STEVAL-ISQ008V1 Manual de usuario
ST
ST X-NUCLEO-OUT02A1 Manual de usuario
ST
ST STEVAL-IDB013V1 Guía del administrador
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
