Spirax Sarco LCR2250 Manual de usuario

IM-P693-01 EMM Issue 2 1

LCR2250 Level Controller

LCR2250

Level Controller

Installation and Maintenance Instructions

IM-P693-01

EMM Issue 2

850143-01

1. Safety information

2. General product information

3. Mechanical installation

4. Electrical installation

5. Commissioning

6. Fault finding

7. Technical information

8. Technical assistance

Printed in Germany

IM-P693-01 EMM Issue 2

LCR2250 Level Controller

The equipment may only be installed, electrically connected and commissioned by suitable persons

with the relevant instruction/training.

Maintenance and modification may only be performed by authorised staff who have undergone

specific instruction/training.

Danger

The terminal strips of the equipment are live during operation! There is a risk of

serious injury due to electric shock!

Always cut off the power supply to the equipment before installing, removing or

connecting terminal strips!

Important

The name plate specifies the features of the equipment. Do not commission or operate

any item of equipment that does not have its own specific name plate.

Directives and standards

VdTÜV Bulletin "Wasserstand 100" (Water Level 100)

The LCR2250 level controller, in combination with the LP20/LP21/PA420 level transmitter, is type

approved to the VdTÜV Bulletin "Water Level 100".

The VdTÜV "Wasserstand (=Water Level) 100" describes the requirements for water level control

and limiting equipment for boilers.

LV (Low Voltage Directive) and EMC (Electromagnetic Compatibility)

The equipment conforms to the requirements of the Low Voltage Directive 2014/35/EU and the

EMC Directive 2014/30/EU.

ATEX (Atmosphère Explosible)

The equipment must not be used in potentially explosive atmospheres, in accordance with European

Directive 2014/34/EU.

1. Safety information

IM-P693-01 EMM Issue 2 3

LCR2250 Level Controller

2.1 Intended use

The LCR2250 level controller is used in combination with a LP20/LP21/PA420 level transmitter as a limit

switch and water level controller, e.g. in steam and water boiler systems, or in condensate and feedwater

tanks. The level controller indicates when a MIN or MAX water level has been reached, and opens or closes

a control valve.

2.2 Function

The LCR2250 level controller processes the level-dependent current signal from the LP20/LP21/PA420 level

transmitter. This input signal is recognised by the controller as 0 and 100 % of the boiler measuring range,

and shown as an actual value on the 7-segment LED display.

The level controller works with an electrically actuated control valve as a 3-position stepping controller

with proportional-plus-integral control action (PI controller). If the actual value deviates from the setpoint,

the electric actuator is triggered by two output contacts and two flashing LEDs indicate whether the control

valve is opening or closing.

The controller can be configured for fill or discharge control.

A further output contact indicates when a MIN or MAX water level is reached (the desired function can be

selected by a switch). After the de-energizing time has elapsed, the output contact switches over and the

MIN or MAX LED lights up.

Faults in the level transmitter, the electrical connection or the settings are indicated as error codes on the

7-segment LED display. In the event of a malfunction, the MIN and MAX alarm is triggered.

If faults occur only in the LCR2250 level controller, the MIN and MAX alarm is triggered and the system is

restarted.

Parameters can be changed or the MIN/MAX alarm simulated by operating the push buttons. For external

level indication, the LCR2250 level controller has a 4 - 20 mA actual value output.

2. General product information

Fig. 1

IM-P693-01 EMM Issue 2

LCR2250 Level Controller

3. Mechanical installation

3.1 Dimensions (approximate) in mm

12046

Item

1Upper terminal strip

2Lower terminal strip

3Housing

4Support rail TH 35, EN 60715

Fig. 2

3.2 Installation in control cabinet

The LCR2250 level controller is clipped onto a type TH 35, EN 60715 support rail in the control cabinet.

Fig. 2, Item 4.

IM-P693-01 EMM Issue 2 5

LCR2250 Level Controller

3.3 Name plates

Fig. 3

M 0,5A

LP20/

LP21/

PA420

4 W

OUT 4-20mA

actual value

24 V

±20%

IN 4-20mA

+12V

LOOP-

LOOP+

Type

designation

Top

Bottom

Safety information

Manufacturer

Degree of protection

External fuse for output contacts

Ambient temperature

Output

contacts

Supply voltage

Connection

of level

transmitter

Approvals

Disposal

information

Actual value output

Fuse, provided on site

Power consumption

Serial number

IM-P693-01 EMM Issue 2

LCR2250 Level Controller

4. Electrical installation

4.1 Wiring diagram

0.5 A (semi- delay)

1 2

3 4

Item

1Output contact for control valve actuation

2MIN/MAX output contact, de-energizing delay 3 seconds

3Supply voltage connection 24 Vdc with semi-delay fuse 0.5 A provided on site

4Actual value output 4-20 mA

5Central earthing point (CEP) in control cabinet

6Earthing point at auxilliary equipment (e.g.PA420/LP20/LP21).

7Level transmitter LP20/LP21/PA420 4-20 mA.

Fig. 4

MIN/MAX

IM-P693-01 EMM Issue 2 7

LCR2250 Level Controller

4.2 Supply voltage connection

The equipment must be supplied with 24 Vdc from a SELV (Safety Extra Low Voltage ) power supply. An

external 0.5A semi-delay fuse must also be fitted.

This power supply unit must be electrically isolated from dangerous live voltages and meet the requirements

for double or reinforced insulation in accordance with one of the following standards:

EN 50178, EN 61010-1, EN 60730-1, EN 60950-1 or EN 62368-1.

4.3 Connection of output contacts

Wire the upper terminal strip 1 (terminals 16-23), shown in Figure 1, according to the desired switching

functions. Provide an external slow-blow 2.5 A fuse for the output contacts.

When inductive loads are switched off, voltage spikes are produced that may have a major adverse effect on

the operation of control and measuring systems. Connected inductive loads must therefore have interference

suppression (RC combination) as per the manufacturer's specifications.

4.4 Connecting the level transmitter

For connecting the equipment, please use a screened, multi-core control cable with a minimum conductor

size of 0.5 mm2, e.g. LiYCY 2 x 0.5 mm2, maximum length 100 m.

Wire the terminal strip as shown in the wiring diagram (Fig. 4).

Connect the screen as shown in the wiring diagram.

Route the connecting cable between items of equipment separately from power lines.

4.5 Connection of actual value output

For connection, please use a screened, multi-core control cable with a minimum conductor size of 0.5 mm2,

e.g. LiYCY 2 x 0.5 mm2, maximum length 100 m. Please note the load of max. 500 ohms.

Wire the terminal strip as shown in the wiring diagram (Fig. 4).

Connect the screen as shown in the wiring diagram (Fig. 4). Route the connecting cable between items of

equipment separately from power lines.

Any item of equipment that you wish to connect to the terminals for the actual value output 4-20 mA must be

certified to have at least double or reinforced insulation to EN 50178, EN 61010-1, EN 60730-1, EN 60950-1

or EN 62368-1 between the current loop and live parts of the equipment that are not supplied with safety

extra-low voltage (SELV).

Important

Do not use unused terminals as support point terminals.

4.6 Tools

Screwdriver size 3.5 x 100 mm, fully insulated to VDE 0680-1.

IM-P693-01 EMM Issue 2

LCR2250 Level Controller

4.7 Connection of level transmitter

The LCR2250 level controller can be combined with the LP20/LP21/PA420 level transmitter.

For connecting the equipment, please use a screened, multi-core control cable with a minimum conductor

size of 0.5 mm2, e.g. LiYCY 2 x 0.5 mm2, maximum length 100 m.

Connect the screen as shown in the wiring diagram (Fig. 4).

Important

-Please commission the equipment as described in the LP20/LP21/PA420

installation & operating manuals.

-Route the connecting cable between items of equipment separately from power

lines.

IM-P693-01 EMM Issue 2 9

LCR2250 Level Controller

5. Commissioning

5.1 Factory settings

-De-energizing delay: 3 sec. (factory set)

-Current input for the connection of an LP20/LP21/PA420 level transmitter.

-MAX switchpoint AL.Hi = 80 % or MIN switchpoint AL.Lo = 20 %

-Setpoint SP = 50 %

-Proportional band Pb = 20 % of setpoint

-Integral action time ti = 0 s

-Dead band = +/– 5 % of setpoint

-Valve travel time tt = 40 s

-Filter = 2 s

-Fill control function

-MIN/MAX output contact set as MAX alarm

Code switch C: S1 = OFF, S2 = OFF, S3 = ON, S4 = ON See Figure 5

5.2 Changing factory settings

Danger

The upper terminal strip of the equipment is live during operation. There is a risk of

serious injury due to electric shock!

Always cut off the power supply to the equipment before installing, removing or

connecting the terminal strip!

IM-P693-01 EMM Issue 2

LCR2250 Level Controller

5.3 Changing the function and input of the level transmitter

The input and function are determined by the setting of code switch c. To make changes, you can access

the code switch as follows:

-Switch off the supply voltage.

-Remove the lower terminal strip (Fig. 5).

-Insert a screwdriver between the terminal strip and the front frame, to the right and left of the arrow

markings.

-Release the terminal strip on the right and left sides, by turning the screwdriver in the direction of the arrow.

-Remove the terminal strip.

Fig. 5

When your changes are complete:

-Refit the lower terminal strip.

-Switch the supply voltage back on. The equipment restarts

Tabla de contenidos

Otros manuales de Controladores de Spirax Sarco

Spirax Sarco

Spirax Sarco AEL3 Series Manual de usuario

Spirax Sarco

Spirax Sarco AEL8 Series Manual de usuario

Spirax Sarco

Spirax Sarco 3000 Series Manual de usuario

Spirax Sarco

Spirax Sarco AEL5 Series Manual de usuario

Spirax Sarco

Spirax Sarco TN203 E Series Manual de usuario

Spirax Sarco

Spirax Sarco LC2250 Manual de usuario

Spirax Sarco

Spirax Sarco X5 Manual de usuario

Spirax Sarco

Spirax Sarco 1600V Manual de usuario

Spirax Sarco

Spirax Sarco 25T Manual de usuario

Spirax Sarco

Spirax Sarco LC2400 Manual de usuario

Spirax Sarco

Spirax Sarco LC2610 Manual de usuario

Spirax Sarco

Spirax Sarco LC3050 Manual de usuario

Spirax Sarco

Spirax Sarco Spirax-Monnier MP Manual de usuario

Spirax Sarco

Spirax Sarco BC1100 Manual de usuario

Spirax Sarco

Spirax Sarco SX80 Manual de usuario

Spirax Sarco

Spirax Sarco SP500 Manual de usuario

Spirax Sarco

Spirax Sarco SX25 Series Manual de usuario

Spirax Sarco

Spirax Sarco SX100 Hoja de especificaciones

Spirax Sarco

Spirax Sarco BC3250 Manual de usuario

Spirax Sarco

Spirax Sarco AEL8 Series Manual de usuario

Spirax Sarco

Spirax Sarco MPC2 Manual de usuario

Spirax Sarco

Spirax Sarco IP2AM Manual de usuario

Spirax Sarco

Spirax Sarco MPC1 Manual de usuario

Spirax Sarco

Spirax Sarco PN 3000 Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario