SOMFY sonesse 30 rts Manual de instalación
Sonesse 30 RTS Programming Instrucons
Power Supply 24V DC
Frequency bands 433.42 MHz
Torque 2 Nm
Speed 6—28 RPM (Adjustable)
Safety level III
Operang Temperature 32F—140F
Protecve rang IP 30 (For indoor use only)
FCC Compliance
This device complies with Part 15 of the FCC rules. Operang is subject to the following two
condions
[1] This device may not cause harmful interface, and
[2] This device must accept any interference received, including interference that may cause
undesired operaon.
Stripe = Posive
White = Negave
18-2204-SRF
Installaon notes
Make sure that the program buon on the motor head is posioned in the instal-
laon brackets so it is easily accessible. Ideally on an open roll installaon, the
motor head buon should be facing downwards towards the oor so you can see
it. If it is in a cassee then Lafayee will already have the motor installed in the
cassee to make it easy for you to get to. You will be required to press/hold this
buon during the programming sequence or to reset the motor.
Transmier informaon
UP
STOP
DOWN
UP
STOP
DOWN
LED
Indicator
Light
Single Channel
Ver-
LED Lights
Channel
Selector
Five Channel
Version
Back View
Programming
Buon
LED
Indicator
Program
Buon
LED
Indicator
Channel
Selector
Buon(s)
Channel
Selector
Buon(s)
STOP Buon
UP Buon
DOWN
Buon
A) Remotes
B) Wireless
Wall Switch
UP
STOP
DOWN
LED
Indicator
Light
UP
STOP
DOWN
LED Lights
Channel
Selector
UP
DOWN
LED Lights
Channel
Selector
STOP Programming
Buon
Scroll Wheel
Programming (Follow steps 1—5)
[1] Inial setup
A) Connect your proper power source. If you are powering the motor via
a transformer or hardwiring, connect the wires according to your state and local
wires codes.
B) Your motor has been programmed with limits. You will need to pair your motor to your remote.
Please go to secon [6] Pairing.
[2] Pair motor to transmier (only aer full reset)
If you have a mul-channel remote, please select the
appropriate channel you are wanng this shade to be on. Then
press and hold the UP and DOWN buon for a jog then release.
Proceed to step [3] if you get a jog. If the shade does not jog
check your power. Try step [2] again. If you sll don’t get any
response please proceed to step [6].
[3] Checking motor direcon
Press the UP buon on your controller
a) If the shade goes up then proceed to step [4]
b1) if the shade starts to go down then press and hold
The MY buon unl the shade starts to jog.
b2) conrm direcon is correct
Proceed to step [4]
Programming (Connued)
[5] Finalize programming
Press and release the program buon on your transmier with a
small pped utensil and your shade should jog.
Lafayee dealer technical support call: 877-548-0612
[4] Seng limits
1) Move the shade to your desired upper limit. You must hold a
direcon in order for your shade to move right now.
2) Press both MY and DOWN at the same me unl the shade
starts to lower then release both buons.
3) Stop the shade with the MY buon once your shade has
reached your desired lower limit (adjust as needed. The shade
will only move while you HOLD a direcon. Press the UP or
DOWN buon to adjust to your desired lower limit).
4) Press both MY and UP at the same me unl the shade starts
to raise then release both buons.
5) The shade will stop by itself at the top. Once the shade has
stopped hold the MY unl the shade starts to jog then release.
Pairing
[6] Pairing motor informaon to a transmier
a) Hold the white motor head buon for 1 jog then release.
b) Press and release the program buon on your transmier for a jog.
Test your limits and ensure limits are properly set. If you need to adjust
please go to step [7—8].
c) If the shade will only move when you hold a direcon proceed to step
[3]
*** There is no automac ALL channel. You must repeat this step every me you are adding the motor to an
addional channel ***
Erasing motor sengs
[9] Erase all motor sengs
*** Doing this will delete all motor limits and any remotes that
was programmed to this motor ***
Press and hold the white motor head buon for 3 connuous jogs.
You will now need to go to step [2].
Lafayee dealer technical support call: 877-548-0612
Adjusng end limits
[7] Adjusng UPPER limit
1) Press and release UP. Let the shade go to its CURRENT upper
limit and stop.
2) Hold both UP and DOWN at the same me for a jog.
3) Adjust the shade with the UP or DOWN buon to your new limit.
The shade will only move when you HOLD a direcon.
4) Hold the MY buon for a jog.
[8] Adjusng LOWER limit
1) Press and release DOWN. Let the shade go to its CURRENT lower
limit.
2) Hold UP and DOWN at the same me for a jog.
3) Adjust the shade with the UP or DOWN buon to your new limit.
The shade will only move when you HOLD a direcon.
4) Hold the MY buon for a jog.
Favorite posion
[10] Seng your favorite posion
1) Move shade to your desired favorite posion
2) Hold the MY buon
To go to your favorite posion just press and release the MY buon
Troubleshoong Secon
What is happening Possible x
Motor does not respond Reverse the wiring on the motor.
Shade is skipping / clicking while it travels 1) The motor drive is not put into the tube correctly. Remove
the motor and ensure the drive is put in the correct orienta-
on
2) The shade is too ght in the brackets. Ensure you have a free
gap on the idler end.
3) You need a new crown/drive kit
Shade is making a vibrang sound You need to adjust/shim your installaon brackets for the shade
Shade squeaks while it travels Lubricate the idler end plug.
Shade will only move while I hold a direcon 1) If you were adjusng a limit from user mode, you just need
to conrm your new limits. Move the shade to where you
wanted the new limit and then press and HOLD the MY
buon for a jog
2) The motor is sll in programming mode. Please go back to
step [3] under Programming.
3) If none of those opons work, reset the motor and start
over. Go to step [9] Erasing Motor Sengs
Motor keeps loosing its limits This will happen if the motor was not nalized during the
programming process. Completely reset the motor. Go Erasing
Motor Sengs step [9].
Otros manuales para sonesse 30 rts
8
Tabla de contenidos
Otros manuales de Motor de SOMFY
SOMFY
SOMFY Altus RTS 120 V Instrucciones de funcionamiento
SOMFY
SOMFY PHOENIX PH 30/14 Manual de usuario
SOMFY
SOMFY Sonesse 30 PoE Instrucciones de funcionamiento
SOMFY
SOMFY LT50 RS485 Manual de usuario
SOMFY
SOMFY Ilmo 40 WT Manual de usuario
SOMFY
SOMFY OXIMO 40 AUTO io Manual de usuario
SOMFY
SOMFY Sonesse 40 PA Manual de usuario
SOMFY
SOMFY LS40 404R2 Manual de usuario
SOMFY
SOMFY ilmo 50 S WT Manual de usuario
SOMFY
SOMFY Altus RTS Instrucciones de uso
SOMFY
SOMFY Altus Manual de usuario
SOMFY
SOMFY Sonesse 40 PA Manual de usuario
SOMFY
SOMFY Roll Up 28 WireFree RTS Manual de usuario
SOMFY
SOMFY Sonesse 30 Manual de usuario
SOMFY
SOMFY ILT 2 Manual de usuario
SOMFY
SOMFY Tilt & Lift 25 RTS Central Manual de usuario
SOMFY
SOMFY Sonesse 30 PoE Manual de usuario
SOMFY
SOMFY LT 50 PA Manual de usuario
SOMFY
SOMFY LT50 Manual de servicio
SOMFY
SOMFY Cord Lift 32 RTS Manual de usuario
