SOMFY LS 40 Manual de usuario
Motorisation of
Window Coverings
using
Somfy Motors
Motorisation of Window Coverings
using Somfy Motors
Functioning Principal
• The motor drives the wheel
• The wheel drives the roller tube
• The roller tube drives the crown
• The crown drives the limit switch within the motor
ATTENTION
Somfy Motors are not waterproof
Do not hose down with water.
All motors mounted externally require covering!
Motorisation of Window Coverings
using Somfy Motors
Motor Range
LS40 Motor
Suitable for roller, roman, 50mm venetian and timber venetian blinds
Power Cable
Blue = Neutral
Brown = Active (direction 1)
Black = Active (direction 2)
Class II double insulated motor (no earth wire)
Nominal Supply Voltage = 220/240V
Current consumption at nominal torque = 100 watts (maximum)
Running Current = 0.5 amps (maximum)
Cable length = 2.5m
Cable size = 3 x 0.75
Important!
LS40 motors must never be wired in parallel.
Damage caused by parallel wiring will not be covered under warranty.
LT50 Motor
Suitable for roller blinds and awnings
Power Cable
Blue = Neutral
Brown = Active (direction 1)
Black = Active (direction 2)
Green/Yellow = Earth
Nominal Supply Voltage = 220/240V
Current consumption at nominal torque = 270 watts (maximum)
Running Current = 1.2 amps (maximum)
Cable length = 2.5m
Cable size = 4 x 0.75
Important!
LT50 motors must never be wired in parallel.
Damage caused by parallel wiring will not be covered under warranty.
Motorisation of Window Coverings
using Somfy Motors
ILT Motor
Suitable for roman and roller blinds
Power Cable
Blue = Neutral
Brown = Active
Green/Yellow = Earth
Cable length = 2.5m
Cable size = 3 x 0.75
Data Cable (4 wire flat phone cable)
RJ9 Connections
Red = up command
Blue = common
White =Supply + 5 volts
Yellow = down command
Cable length = 2m
Cable size = Flat 4 core multistrand date cable
Nominal Supply Voltage = 220/240V
Current consumption at nominal torque = 270 watts (maximum)
Running Current = 1.2 amps (maximum)
Altus 40 Motor (integrated Radio receiver)
Suitable for roller and roman blinds
Power Cable
Blue = Neutral
Brown = Active
Class II double insulated motor (no earth wire)
Nominal Supply Voltage = 220/240V
Current consumption at nominal torque = 100 watts (maximum)
Running Current = 0.5 amps (maximum)
Cable length = 2.5m
Cable size = 2 x 0.75
Motorisation of Window Coverings
using Somfy Motors
Altus 50 Motor (integrated Radio receiver)
Suitable for roller and roman blinds plus awnings
Power Cable
Blue = Neutral
Brown = Active
Green/Yellow = Earth
Nominal Supply Voltage = 220/240V
Current consumption at nominal torque = 270 watts (maximum)
Running Current = 1.2 amps (maximum)
Cable length = 3m
Cable size = 3 x 0.75
Concept 25 Motors
Suitable for slimline venetians, pleated and cellular blinds
Nominal Supply Voltage = 24V DC
Current consumption = 600 mA (maximum)
Cable length = 2.5m
Cable size = 2 x 0.25
Motorisation of Window Coverings
using Somfy Motors
Wiring Considerations
LS40 and LT 50 Motors
Do not wire Somfy motors and controls without first consulting the wiring diagrams.
Determine which of the drown and black wires correspond to the UP and DOWN
direction prior to the final wiring.
Connect the Earth Wire.
Check that the wire size is in accordance to the number and electrical rating of motors
as outlined in local authority guidelines.
Consider climatic conditions such as temperature and humidity when installing Somfy
controllers. Install control boxes indoors, or use waterproof boxes for outdoor
installations.
Do Not use other switches and controls other than those recommended by Somfy.
When using a Somfy control box plug in type, make sure the power supply is
switched off before plugging in.
! Use one switch per motor. Do not wire one motor to several switches without
using the appropriate Somfy electronic control!
Problem
When ‘switch 1’ is turned to the UP position, the motor will turn. When it reaches its
pre-set position, micro-switch “M1’ will open and the motor will stop.
If ‘switch 2’ is then turned to the down position, the motor will turn in the opposite
direction. Micro-switch ‘M1’ will close. This will cause the capacitor to short circuit
through micro-switch ‘M1’ and ‘switch 1’.
This will damage the contacts in the micro-switch.
Solution
Use Somfy CD4 or other Somfy electronic controller
Motorisation of Window Coverings
using Somfy Motors
Wiring Considerations
LS40 and LT 50 Motors
Problem
When the switch is turned to either the up or the down position, both motors will turn
together.
One of the motors (A) will stop at its pre-set limit before the other (B).
Current from motor (B) will then flow back through to motor (A) through capacitor
C2 and micro-switches M3 and M1.
There will be constant feedback from one motor to the other causing the motors to
continuously change direction, but with very little travel.
The motors will eventually burn out.
Solution
For one of more motors use a Somfy group controller.
Motorisation of Window Coverings
using Somfy Motors
Integration to BMS using LS40 or LT50
Option 1
CD4 individual motor controller
• Requires 240V power supply and has 240V latched output
• Provides interlocking between up and down commands
• Dry contact impulse switching (impulse contact closure of 1 second minimum)
• Contact between common and up or common and down to activate motor
• Simultaneous contact between a common up and down to create a stop
• CD4 Venetian module available for control of Venetian blinds
• Dimensions: 112 (h) x 52 (w) x 106 (d)
Note: Earth wire not required for LS40 motors
Motorisation of Window Coverings
using Somfy Motors
Integration to BMS using LS40 or LT50
Option 2
Moduline Controllers
• DIN rail mounted controllers
• Requires 240 V power supply
• Dry contact impulse switching (impulse contact closure of 1 second minimum)
• Contact between common and up or common and down to activate motor
• Simultaneous contact between a common up and down to create a stop
ML9000 Power supply and master controller
• Can control up to 16 individual motor controllers
• Dimensions: 85 (h) x 70 (w) x 62 (d) – 4 DIN rail slots
ML8000 Individual motor controller
• Control of 1 motor via dry contact impulse switching
• Receives power from a ML9000
• Dimensions: 85 (h) x 35 (w) x 62 (d) – 2 DIN rail slots
ML8100 Individual Venetian motor controller
• Control of 1 motor with tilt functionality via dry contact impulse switching
• Receives power from a ML9000
• Dimensions: 85 (h) x 35 (w) x 62 (d) – 2 DIN rail slots
Motorisation of Window Coverings
using Somfy Motors
Integration to BMS using LS40 or LT50
Option 3
Animeo IB+ AC Motor Controller
• Requires 240V power supply and has 240V latched output
• Provides interlocking between up and down commands
• Dry contact impulse switching (impulse contact closure of 1 second minimum)
• Contact between common and up or common and down to activate motor
• Simultaneous contact between a common up and down to create a stop
• Allows for group and individual control of up to 4 motors
• Surface or DIN rail mountable - 12 DIN rail slots
• Dimensions: 180 (h) x 250 (w) x 63 (d)
Otros manuales para LS 40
4
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Motor de SOMFY
SOMFY
SOMFY RDO 50 CSI Manual de usuario
SOMFY
SOMFY LV25 Manual de usuario
SOMFY
SOMFY WIREFREE LT-30RT Instrucciones de funcionamiento
SOMFY
SOMFY OREA WT Manual de usuario
SOMFY
SOMFY Sonesse Ultra 50 Manual de usuario
SOMFY
SOMFY sonesse 30 rts Manual de instalación
SOMFY
SOMFY LT50 CMO Manual de usuario
SOMFY
SOMFY LS 40 Manual de usuario
SOMFY
SOMFY ILT 2 Manual de usuario
SOMFY
SOMFY Pergola io Instrucciones de montaje
SOMFY
SOMFY Sonesse 30 RS485 Manual de usuario
SOMFY
SOMFY ALTUS 40 RTS Manual de usuario
SOMFY
SOMFY Oximo RTS Manual de usuario
SOMFY
SOMFY Sonesse 30 PoE Instrucciones de funcionamiento
SOMFY
SOMFY Sunea io Manual de usuario
SOMFY
SOMFY Elite Smart Shades R28 WireFree RTS Manual de instalación
SOMFY
SOMFY Sonesse Ultra 50 RTS Manual de usuario
SOMFY
SOMFY VRA 10 Manual de usuario
SOMFY
SOMFY LIGHTING OUTDOOR RTS Instrucciones de funcionamiento
SOMFY
SOMFY LT50 CMO Instrucciones de uso
