SolarEdge SE3K-RWB Manual de usuario

Installation Guide

SolarEdge System Installation

Guide

For Europe and APAC

Version 4.2

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or

transmitted, in any form or by any means, electronic, mechanical, photographic,

magnetic or otherwise, without the prior written permission of SolarEdge Inc.

The material furnished in this document is believed to be accurate and reliable.

However, SolarEdge assumes no responsibility for the use of this material. SolarEdge

reserves the right to make changes to the material at any time and without notice. You

may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Patent marking notice: see http://www.solaredge.com/patent

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where

necessary. However, discrepancies cannot be excluded. No guarantee is made for the

completeness of these documents.

The images contained in this document are for illustrative purposes only and may vary

depending on product models.

Emission Compliance

This equipment has been tested and found to comply with the limits applied by the

local regulations.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, you are encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Disclaimers 1

Three Phase System MAN-01-00507-4.2

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

Three Phase System MAN-01-00507-4.2

2 Emission Compliance

Revision History

Version 4.2 (May 2020)

Modified the procedure for disconnecting the DC power and deleted the

introduction in the Safe DC Appendix.

Modified Power Optimizer Guidelines section: Length of home - run cabels

maximum values , Extension cables rules, Power optimizer clearance

Modified RS485 terminology - Master is now Leader and Slave is Follower,

respectively

Version 4.1 (February 2019)

Added appendix 'Determining the Circuit Breaker Size' and paragraph referencing

to it, in the 'Grid Connection Guidelines' section.

In Specifications removed 'Recommended OCPD size per grid' table.

Version 4.0 (July 2018)

This guide describes three phase inverters only

Update of product names

Removal of grounding cable connected to the DINrail in the DC Safety Unit.

Hardware change - new enclosure, interfaces and communication board

Addition of possibility to use compatible connectors from third-party

manufacturers

Update regarding use of extension cables in power optimizer installation guidelines

Recommendation to mount the power optimizer in a location protected from direct

sunlight

Power optimizer clearance - no clearance is required on the mounting bracket side

Addition of caution - installation in saline environment

Clearance for three phase inverters installed side-by-side, single row of inverters

outdoors: 5 cm / 2”

PVRSSis enabled by default. Enabling/ disabling PVRSS feature can be done from

the inverter LCD menus.

Addition of reference to troubleshooting undetected devices application note

Revision History 3

Three Phase System MAN-01-00507-4.2

Torque for connecting DC strings to the fuse holders in the DC Safety Unit: 3.4 N*M

/ 30 lb*in

Addition of link to the Designer web page

Updated warning about sealing unused power optimizer input connectors

DC safety voltage is 1V (±0.1V)

Addition of link to Three Phase Inverters for Delta Grids application note

Addition of RS485-2 support

Version 3.3 (Aug.2017)

Updated the Safety section: New warning -The Safety Switch meets all

requirements for a code-compliant installation of this system. The DC Disconnect

Switch disconnects both the positive and negative conductors.

In Supported AC Grids, added:Ground connection is required for all grids

In Power Optimizer Installation chapter:

Updated string extension cable length

Added information for connecting multiple modules in parallel to an optimizer

Removed reference to racking models and their grounding methods

Removed mentioning of tracker

In inverter Installation chapter:

Added note about copper conductors

Removed previous interface panel description and images, and type 1 bracket

In Inverter Interfaces - updated ON/OFFswitch description

Added a caution about not altering the DC Safety Unit enclosure:SolarEdge

does not permit opening or puncturing the Safety Switch in any location other

than the pre-defined drill guide locations, or otherwise altering the

construction of the enclosure, as this may compromise safety and will void the

warranty.

Reference to horizontal mounting application note

Updated clearance specifications

Connection to/from the Connection Unit:

Three Phase System MAN-01-00507-4.2

4 Revision History

AC grounding to bus bar instead of terminal block - updated instructions and

Connection Unit model images

String fusing requirement note updated:Fuses needed for 4 strings or more

(instead of 3).

Added conduit sealing requirement

In Commissioning chapter:

Updated the activation sequence

Updated menu information descriptions

Removed RS232 reference

In Configuration Menu Options:

Communication section:

Removed RS232 Conf

Added GSMConf

Power Control section:

Removed Phase Balance link and info

Add link to P(Q) diagram application note

Maintenance section:

Added links to application notes (Upgrading the inverter using SD card;

Isolation fault troubleshooting; Arc fault detection)

Removed Optimizer Conf

Status Screens updates:

Meter status screen - added Power and Energy lines

Telemetry status screen - updated

GSMstatus screen - new

Communication options - updated

Inverter cover removal sequence - updated

RS485-E option - new

Added link to Arc Detection application note

Troubleshooting:

Error codes moved to a separate document. A link was added to the manual.

Slave Detect and Slave List - updated

Revision History 5

Three Phase System MAN-01-00507-4.2

External fan replacement - updated

Explained whichoptimizerinstallation steps to skip when using smart modules.

Added RS485 slave detect feature

Removed USB

Three Phase System MAN-01-00507-4.2

6 Revision History

Contents

Disclaimers 1

Important Notice 1

Emission Compliance 1

Revision History 3

HANDLING AND SAFETY INSTRUCTIONS 9

Safety Symbols Information 9

Inverter Interfaces 9

IMPORTANTSAFETYINSTRUCTIONS 13

Chapter 1: Introducing the SolarEdge Power Harvesting System 15

Power Optimizer 15

Inverter 16

Monitoring Platform 16

Installation Procedure 16

Installation Equipment List 16

Inverter Transport and Storage 17

Chapter 2: Installing the Power Optimizer 18

Safety 18

Installation Guidelines 19

Step 1: Mounting the Power Optimizers 22

Step 2: Connecting a PV module to a Power Optimizer 22

Step 3: Connecting Power Optimizers in Strings 23

Step 4: Verifying Proper Power Optimizer Connection 24

Chapter 3: Installing the Inverter 25

Inverter Package Contents 25

Identifying the Inverter 25

Mounting the Inverter 25

Chapter 4: Connecting the AC and the Strings to the Inverter 30

Grid Connection Guidelines 30

Connecting the ACGrid to the Inverter 30

Connecting the Strings to the Inverter 33

Selecting a Residual Current Device (RCD) 33

Chapter 5: Commissioning the Installation 35

Step 1: Activating the System 35

Step 2: Pairing Power Optimizers to the Inverter 37

Step 3: Verifying Proper Activation 40

Step 4: Reporting and Monitoring Installation Data 40

Chapter 6: User Interface 44

Revision History 7

Three Phase System MAN-01-00507-4.2

LCD User Buttons 44

Inverter Configuration – Setup Mode 46

Configuration Menu Options 51

Status Screens - Operational Mode 56

Chapter 7: Setting Up Communication to the Monitoring Platform 65

Communication Options 65

Communication Connectors 68

Removing the Inverter Cover 69

Removing the DC Safety Unit Cover 69

Creating an Ethernet (LAN) Connection 69

Creating an RS485 Bus Connection 73

Verifying the Connection 77

Appendix A: Errors and Troubleshooting 78

Troubleshooting Communication 78

Power Optimizer Troubleshooting 81

Appendix B: Mechanical Specifications 83

Appendix C: Connecting the AC and DCStrings to the DC Safety Unit 84

Connecting the ACGrid to the Inverter 85

Connecting the Strings to the DC Safety Unit 86

Appendix D: SafeDC™ 88

Appendix E: External Fan Maintenance and Replacement 90

Fan Maintenance 90

External Fan Replacement 90

Appendix F: Replacing and Adding System Components 92

Replacing an Inverter 92

Replacing the DC Safety Unit 93

Adding, Removing, or Replacing Power Optimizers 96

Determining the Circuit Breaker Size 97

Revision History 97

Introduction 97

Using Transformers in Commercial Three Phase Inverter Installations 97

Determining the Size of an Inverter Circuit Breaker 98

Technical Specifications - Three Phase Inverters (Europe &APAC) 101

Support Contact Information 109

Three Phase System MAN-01-00507-4.2

8 Revision History

HANDLING AND SAFETY INSTRUCTIONS

During installation, testing and inspection, adherence to all the handling and safety

instructions is mandatory. Failure to do so may result in injury or loss of life and

damage to the equipment.

Safety Symbols Information

The following safety symbols are used in this document. Familiarize yourself with the

symbols and their meaning before installing or operating the system.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in injury or loss of life. Do not proceed

beyond a warning note until the indicated conditions are fully understood and

met.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in damage or destruction of the

product. Do not proceed beyond a caution sign until the indicated conditions

are fully understood and met.

NOTE

Denotes additional information about the current subject.

IMPORTANTSAFETYFEATURE

Denotes information about safety issues.

Disposal requirements under the Waste Electrical and Electronic Equipment (WEEE)

regulations:

NOTE

Discard this product according to local regulations or send it back to SolarEdge.

Inverter Interfaces

The following figure shows the inverter connectors and components, located at the

bottom of the inverter.

HANDLING AND SAFETY INSTRUCTIONS 9

Three Phase System MAN-01-00507-4.2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de SolarEdge

SolarEdge

SolarEdge Inline Energy Meter Manual de usuario

SolarEdge

SolarEdge StorEdge SE5000-xxS0 series Manual de usuario

SolarEdge

SolarEdge SE3000 Manual de usuario

SolarEdge

SolarEdge SE K Series Manual de usuario

SolarEdge

SolarEdge Solar Inverter Manual de usuario

SolarEdge

SolarEdge StorEdge SE7600A-USS Manual de usuario

SolarEdge

SolarEdge StorEdge Interface SESTI-S4 Manual de usuario

SolarEdge

SolarEdge storedge Manual de usuario

SolarEdge

SolarEdge SE3000US Manual de usuario

SolarEdge

SolarEdge Power Harvesting System Manual de usuario

SolarEdge

SolarEdge storedge Manual de usuario

SolarEdge

SolarEdge SE8000H-AU Manual de usuario

SolarEdge

SolarEdge Home Hub Inverter Three Phase Manual de usuario

SolarEdge

SolarEdge UL1741-SA Manual de usuario

SolarEdge

SolarEdge SE8K-N4 Manual de usuario

SolarEdge

SolarEdge SE2200H Manual de usuario

SolarEdge

SolarEdge SE2200 Manual de usuario

SolarEdge

SolarEdge T568B Manual de usuario

SolarEdge

SolarEdge 3000A-US Manual de usuario

SolarEdge

SolarEdge SE15K Manual de usuario

SolarEdge

SolarEdge storedge Manual de usuario

SolarEdge

SolarEdge StorEdge SE10K-RWS Manual de usuario

SolarEdge

SolarEdge SE7600A-US Manual de usuario

SolarEdge

SolarEdge SE5000H-AU Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario