DIAGNOSTIC LEDs
BLUE NUBI pre-alarm in test mode.
GREEN Flash when the smoke artridge is triggered.
RED Warnings.
OUTPUTS
ALL output is a tive for 90 se onds starting from the
starting of smoke delivery. SW6 sets the output logi , when
use internal siren, set SW6 to OFF.
BL output is a tive when the battery is low. SW5 sets the
output logi .
24H output is a lear onta t normally losed when the
NUBI 4.0 box is losed, it will open when the box will be
opened. When the SW8 is set to ON, tamper output is
disabled (output is always losed).
PIR RANGE
The pi ture below shows the PIR range
TEST MODE
Set the DIP SW7 to ON to a tivate the test mode. As soon
as the devi e enters test mode, the green LED will flash to
indi ate the battery status:
•3 times: full harge
•2 times: medium harge.
•1 time: quite low.
•RED LED flash + Buzzer: low (to be repla ed)
Then the BLUE led will flash slowly, one time ea h se ond,
to indi ate the test mode is a tivated. In test mode, ea h
time the integrated PIR dete t movement, the RED led
flash and the buzzer will sound for 1 se ond.
the RED led on smoke artridge validation board will be
OFF when the artridge is empty, flash otherwise.
When the SI input dete ts that the system is armed, an
event between the dete tion of the PIR movement or the
a tivation of the ALL input will ause the NUBI 4.0 pre-
alarm state for 15 minutes and the BLUE led will flash
qui kly. When the se ond alarm event o urs within the
pre-alarm period, the GREEN led will flash for 1 se ond to
indi ate the simulation of smoke delivery.
If the pre-alarm was aused by the PIR dete tion, the
alarm onfirmation will be due to the a tivation of the ALL
input. If the pre-alarm was aused by the a tivation of the
ALL input, the onfirmation will o ur whit the PIR
dete tion. In test mode, the smoke artridge will never be
a tivated and never the validation ard will be damaged.
Remembe to activate the ope ating mode (DIP SW7
OFF) at the end of testing.
SMOKE CARTRIDGE REPLACEMENT
When a smoke artridge is empty, it must be repla ed with
a new one. The smoke artridge is supplied with the
validation ard welded to the ends of the wires. Only in test
mode (SW7 ON) the RED led on validation board is OFF
when the artridge is empty, then flash when the artridge
is full.
Remove the NUBI 4.0 batte y powe supply and wait
at least 3 minutes befo e eplacing the smoke
ca t idge.
1) Remove from the motherboard the old validation
ard soldered onto the wires of the empty smoke
artridge.
2) Insert the new validation ard soldered onto the
wires of the new artridge.
Commissioning
We advise to perform a test (see previous hapter Test
mode) before perform a definitive ommissioning of the
devi e.
Set the DIP SW7 to OFF to swit h in operating mode.
We advise to remove the adhesive that prote ts smoke
exit hole of the smoke artridge.
WARNING PROCEDURE TO PREVENT SMOKE
EMISSION AT THE POWER UP
During the first 30 minutes after power the devi e, there
is a spe ial fun tion to prevent unwanted smoke
emissions, for example due to wiring errors.
When the smoke a tivation ondition o urs during this
time, instead of immediately emitting smoke, a warning
pro edure starts and the buzzer emits an intermittent
sound for 120 se onds and the red LED flashes.
It will be possible to stop the a tivation by opening the
box and setting the DIP SW7 to ON or, in ase of
diffi ulty, it will also be possible to unplug the smoke
artridge validation ard from the motherboard.
If this warning pro edure is not interrupted, at the end of
the 120 se onds we will have the emission of smoke.
MAINTENANCE
We re ommend repla ing the smoke apsule every 5
years using only the original repla ement.
