SIIG CE-H20011-S1 Manual de usuario
1
Introducing the HDMI Extender
The HDMI Extender over 1 CAT5e extends HDMI signals
via 1 CAT5e/6 cable to virtually any HDMI enabled
display. This cost effective solution provides flexibility
forHDMIenableddevicestotransmithighqualityaudio/
video to greater distances at minimal cost.
FeaturesandBenefits
• Extends audio/video transmission from an HDMI
source to an HDMI display over one economical
CAT5e/6 cable
• Minimize cable skew with the adjustable 8-level
equalization knob
• Compatible with DVI monitors
• HDMI 1.2a and HDCP compatible
• Bandwidth: 1.65 Gps
• Supports distances up to 60m/200 ft @ 720P/1080i
or 40m/130 ft @ 1080p
PackageContents
• HDMI transmitter (TX)
• HDMI receiver (RX)
• 2x Power adapter (5V, 4A)
• Quick Installation Guide
04-0502A
HDMIExtenderOver1CAT5e
Quick Installation Guide
2
Layout
• HDMI-IN: Connect to a HDMI source with a HDMI
M-M cable (not included) here
• RJ45-OUT: Plug in a CAT5e/6 cable, to be linked to
the RJ-45 connector of the HDMI receiver
• +5V DC: connect to 5V DC power supply
• Mode:
0 HDMI mode with 8-channel audio output
1 = HDMI mode with 2-channel audio output
2 = DVI mode
3-5 = Reserved
6 = Use default EDID
7 = Learn EDID from the display.
Note: If no image appears on the HDMI display,
turn the dial to Mode 7 to read the EDID of the
connected HDMI display.
Figure 1: Transmitter (front and back)
3
• HDMI-OUT: connect to a HDMI display with a
HDMI M-M cable (not included) here
• EQ: adjusts the equilization of the received signal
from 0 (strongest) to 7 (weakest). It is recommended
to try each setting, from 0 to 7 to find the optimal
visual experience
• RJ45-IN: plug in a CAT5e/6 cable that needs to be
linkedtotheRJ-45connectoroftheHDMItransmitter
receiver
• +5V DC: connect to 5V DC power supply
Figure 2: Receiver (front)
Figure 3: Receiver (back)
4
Hardware Installation
1. Connect your HDMI source to the transmitting unit.
2. Connect your HDMI display to the receiving unit.
3. Connect your CAT5e/6 cable between the
transmitting and receiving units. Make sure the
cable is securely connected and not loose.
4. Plug in the power adapter to each unit, then plug the
power adapters into a reliable power source.
5. If the image is flickering or blinking, try to improve
the cable skew by adjusting the equilization (EQ)
switch from 0 - 7 (strongest - weakest) to find the
optimal visual experience.
Notes
1. If your HDMI/DVI device requires and EDID, you
can use an EDID Reader/Writer to provide HDMI/
DVI EDID information.
2. Alltransmissiondistances referenced in thismanual
are measured using a CAT5e 125MHz cable. The
distance is measure between the HDMI Transmitter
unit and the HDMI display.
3. To reduce interference among the unshielded
twistedpairs of wire in the CAT5ecable,useshielded
CAT5e cables to improve EMI problems which
worsens in longer distances.
4. Transmission length and quality of the received
display depends on the quality of the CAT5e cable.
5. For resolutions greater than 1080i or 1280x1024 a
CAT6 cable is recommended.
5
Blank Page
6
Blank Page
7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support hasanswers! Simplyvisitour
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
toyour questions couldbejust a fewclicksaway. You can alsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffers a 2-year manufacturer warranty withthisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyour purchase has passedthestore's return policy period,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
•Clearly write your RMA number on the top of the returned
package. SIIGwill refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
HDMI Extender over 1 CAT5e is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Other names used in this publication are for identification only and may be
trademarksoftheirrespectivecompanies.
September, 2008 Copyright © 2008 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/b),networking, sound cards,andother accessories. SIIG is the
premier one-stop source of upgrades.
SIIGproducts offer comprehensiveuser manuals, manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
HDMI Extender over 1 CAT5e
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Ph: 510-657-8688
Tabla de contenidos
Otros manuales de Extensor de SIIG
SIIG
SIIG CE-DP0511-S1 Manual de usuario
SIIG
SIIG 04-1404A Manual de usuario
SIIG
SIIG AV-GM03W3-S1 Manual de usuario
SIIG
SIIG CE-H20S11-S1 Manual de usuario
SIIG
SIIG AV-GM03K3-S1 Manual de usuario
SIIG
SIIG AV-GM0473-S1 Manual de usuario
SIIG
SIIG CE-DV0061-S1 Manual de usuario
SIIG
SIIG CE-D20111-S1 Manual de usuario
SIIG
SIIG JU-EX0111-S1 Manual de usuario
SIIG
SIIG CAT5e Manual de usuario
SIIG
SIIG CE-VG0711-SA Manual de usuario
SIIG
SIIG CE-H27611-S1 Manual de usuario
SIIG
SIIG AV-GM03T3-S1 Manual de usuario
SIIG
SIIG CE-HM0051-S1 Manual de usuario
SIIG
SIIG AV-GM03G3-S1 Manual de usuario
SIIG
SIIG CE-H22T11-S1 Manual de usuario
SIIG
SIIG CE-KV0511-S1 Manual de usuario
SIIG
SIIG CE-HM0052-S1 Manual de usuario
SIIG
SIIG AV-GM04Q3-S1 Manual de usuario
SIIG
SIIG CE-D20012-S1 Manual de usuario
