SIIG JU-2NE012 Manual de usuario

USB 2.0+FireWire+10/100

Quick Installation Guide

04-0279B

Introducing the USB 2.0+Firewire+10/100

TheUSB2.0+Firewire+10/100CombodesignaddsUSB2.0,

FireWire(1394a),and10/100(RJ45)Ethernetinterfacesto

your system.

Features and Benefits

USB 2.0 interface:

• Adds two external and one internal USB 2.0 ports

• Compliant with USB specification rev. 2.0

• Supports high-speed (480 Mbps), full-speed (12

Mbps), and low-speed (1.5 Mbps) data transfer

modes for simultaneous operation of multiple USB

2.0/1.1 devices

• Hot-swapping feature allows you to connect/

disconnect devices without powering down your

system

• WorkswithavarioustypeofUSBdevicesincluding

hubs, removable drives, digital cameras, scanners,

CD-RWs, DVD-ROMs, PC video cameras, printers,

CF/SM/MMC/SD/Memory Stick memory card

readers, and more...

Note: USB1.1 devicesare limitedto USB1.1 speeds

evenwhentheyareconnectedtoUSB2.0hostadapter

or USB 2.0 hubs.

FireWire (1394a) interface:

• AddsoneexternalandoneinternalFireWire(1394a)

ports

• Compliant with IEEE 1394-1995, P1394a-2000 and

OHCI 1.1 standards

• Supports serial bus data transfer rates of 100, 200

and 400 Mbps

• Hot-swapping feature allows you to connect/

disconnect devices without powering down your

system

• Workswith varioustypes of1394devicesincluding

DV camcorders/cameras, hard disk drives,

CD-RWs,DVD-ROMs,removabledrives,scanners,

and other audio/video devices

10/100 Ethernet (RJ45) interface:

• Adds a 10/100 Ethernet interface

• Compliant to PC99 and PC2001 standards

• Half/Full duplex capability

• Supports Full Duplex Flow Control (IEEE 802.3x)

• Supports 10 Mb/s and 100 Mb/s operation and

N-way Auto-negotiation operation

• Contains two large (2Kbyte) independent receive

and transmit FIFO's

System Requirements

•Pentium or equivalent computer with an available

PCI slot

• Windows 98SE/ME/2000/XP/Server 2003

Package Contents

•(1) USB 2.0+Firewire+10/100 Combo adapter

•(1) Driver CD

•This quick installation guide

Layout

Figure 1. Layout

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer’s case for a few

seconds. Avoid any contact with internal parts and

handle cards only by their external edges.

1. Turn OFF the power to your computer and any

other connected peripheral devices.

2. Unplug the power cord from the back of the

computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card's bus

connectorwiththeselectedPCIslot,pushtheboard

down firmly, but gently, until it is well seated.

10/100

Ethernet

FireWire

USB 2.0

FireWire

USB 2.0

6. Replace the slot bracket's holding screw to secure

the card.

7. Replacethecomputercoverandreconnectthepower

cord.

Driver Installation

This sections provides information on how to install the

USB 2.0+Firewire+10/100 drivers

Windows 98SE

1. Boot up Windows. At the Add New Hardware

Wizard, click Cancel.

2. Insert the driver CD, click Start, Run, type in

X:\USB2\setup206.exe, then click OK. (Change X:

to match the drive letter of your CD-ROM)

3. SelectYes,Iwanttorestartmycomputernow,then

click Close.

4. WhenWindowsresumes,attheAddNewHardware

Wizard, click Next.

5. Insert the driver CD, choose Search for the best

driver..., then click Next.

6. Uncheck all boxes and click Next.

7. Click Next and Finish.

8. ThePCIEthernetControllerisnowdetected. Atthe

Add New Hardware Wizard, click Next.

9. Select Search for the best driver... and click Next.

10. Select Specify a location, type in X:\Lan\win98,

thenclickNext. (ChangeX:tomatchthedriveletter

of your CD-ROM)

11. Click Next and Finish.

12. Click No when asked to restart.

13. At the Add New Hardware Wizard, click Next.

14. Select Search for the best driver... and click Next.

15. Uncheck all boxes and click Next.

16. Select The Updated Driver (Recommended) and

click Next.

17. Click Next and Finish.

18. Repeat steps 13-17 two more times.

19. ClickYestorestarttocompletethedriverinstallation.

Windows ME

1. Boot up Windows. At the Add New Hardware

Wizard, click Cancel.

2. Insert the driver CD, click Start, Run, type in

X:\USB2\setup206.exe, then click OK. (Change X:

to match the drive letter of your CD-ROM)

3. Select Yes, I want to restart my computer now, and

click Close.

4. When Windows resumes, the Add New Hardware

Wizard detects PCI standard PCI to PCI bridge,

select Automatic Search for a better driver, click

Next, then click Finish.

5. When the Add New Hardware Wizard detects a

1394HostController,selectAutomaticSearchfora

better driver, click Next, then click Finish.

6. ClickYestorestart tocompletethedriverinstallation.

Windows 2000

If you have Windows 2000 with Service Pack 4 (SP4) or

later, the drivers will be installed automatically by the

operating system. No additional driver installation is

needed. Otherwise,followtheinstructionsintheorderin

which they appear.

1. Boot up Windows. At the Found New Hardware

Wizard, click Cancel.

2. Insert the driver CD, click Start, Run, type in

X:\USB2\setup206.exe, then click OK. (Change X:

to match the drive letter of your CD-ROM)

3. Select Yes, I want to restart my computer now, and

click Close.

4. When Windows resumes, the drivers will install

automatically.

Windows XP

If you have Windows XP with Service Pack 1 (SP1) or

later, the drivers will be installed automatically by the

operating system. No additional driver installation is

needed. Otherwise,followtheinstructionsintheorderin

which they appear.

1. Boot up Windows. At the Found New Hardware

Wizard, click Cancel.

2. Insert the driver CD, click Start, Run, type in

X:\USB2\setup206.exe, then click OK. (Change X:

to match the drive letter of your CD-ROM)

3. Click Continue Anyway.Our driver has been

thoroughly tested in Windows for stability.

4. Select Yes, I want to restart my computer now and

click Close.

5. When Windows resumes, at the Found New

Hardware Wizard, select Install the software

automatically (Recommended), then click Next.

6. Click Continue Anyway and Finish.

7. Repeat steps 5-6 one more time to complete the

installation.

Windows Server 2003

Windows Server 2003 automatically detects and installs

the correct drivers for the USB 2.0+FireWire+10/100. No

additional driver installation is needed.

To Verify Successful Driver Installation

1. Check Device Manager to verify successful driver

installation.

Windows 98SE/ME: Right click MyComputer, click

Properties,then click Device Manager.

Windows 2000/XP/Server 2003: Right click My

Computer, click Manage, then click Device

Manager.

2. Double click Universal Serial Bus controllers.

- NEC PCI to USB Enhanced Host Controller...

- NEC PCI to USB Open Host Controller...

- USB 2.0 Root Hub Device (USB Root Hub for

Server 2003)

- USB Root Hub

3. Double click 1394 Bus Controller or IEEE 1394 Bus

host controllers option and an OHCI Compliant

IEEE 1394 Host Controller should be displayed.

4. DoubleclickNetworkAdaptersandaRealtek...Fast

Ethernet should be displayed.

Technical Support and Warranty

QUESTIONS? SIIG’s Online Support has answers!

Simply visit our website at www.siig.com and click on Support.

Our online support database is updated daily with new drivers

and solutions. Answers to your questions could be just a few clicks

away. Youcanalsosubmitquestionsonlineandoneofourtechnical

support analysts will promptly respond.

A lifetime manufacturer warranty supplied with this product is

offered by SIIG, Inc. Please see SIIG website for more warranty

details. If you should happen to encounter any problems with this

product, please follow the procedures below.

If it is within the store's return policy period, please return the

product to the store where you purchased from.

If your purchase has passed the store's return policy period, please

follow these steps to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, click Support, then RMA to submit a

request to SIIG RMA. If the product is determined to be

defective,anRMAnumberwillbeissued. SIIGRMAdepartment

can also be reached at (510)413-5333.

Step 2: After obtaining an RMA number, ship the product.

•Properlypacktheproductforshipping. Allsoftware,cable(s)

andanyotheraccessories thatcamewiththeoriginal package

must be included.

•Clearly write your RMA number on the top of the returned

package. SIIGwillrefusetoacceptanyshippingpackage,and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

•You are responsible for the cost of shipping the product to

SIIG at the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538

RMA #:

•SIIG will ship the repaired or replaced product via Ground

in the U.S and International Economy outside of the U.S at

no cost to the customer.

USB 2.0+FireWire+10/100 Combo is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are

registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel

Corporation. Other names used in publication are for identification only and may be trademarks

of their respective companies.

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading computer upgrade

manufacturer of I/O connectivity products, including PCI & ISA

serial and parallel ports, USB, Serial ATA & UltraATA controllers,

FireWire(1394a/b),Networking,SoundCards,andotheraccessories.

SIIG is the premier one-stop source of upgrades.

SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly

features, and are backed by an extensive manufacturer warranty.

High-quality control standards are evident by the overall ease of

installation and compatibility of our products, as well as one of the

lowest defective return rates in the industry. SIIG products can be

foundincomputerretailstores,mailordercatalogs,ande-commerce

sites in the Americas and the UK, as well as through major

distributors, system integrators, and VARs.

PRODUCT NAME

USB 2.0+FireWire+10/100 Combo

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

Tabla de contenidos

Otros manuales de Hardware de computadora de SIIG

SIIG

SIIG JJ-EC1012-S1 Manual de usuario

SIIG

SIIG JJ-E02111-S1 Manual de usuario

SIIG

SIIG Cyber I/O PCI Manual de usuario

SIIG

SIIG DP SoundWave 4 Channel PCI Manual de usuario

SIIG

SIIG JU-P40412-S1 Manual de usuario

SIIG

SIIG IO1037 Manual de usuario

SIIG

SIIG UltraATA 133 PCI Manual de usuario

SIIG

SIIG SoundWave 5.1 PCI Manual de usuario

SIIG

SIIG Silent Mini Notebook Cooler Manual de usuario

SIIG

SIIG FireWire 800 2-Port ExpressCard/34 Manual de usuario

SIIG

SIIG eSATA II PCIe i/e Manual de usuario

SIIG

SIIG AV-GM0AK3-S1 Manual de usuario

SIIG

SIIG Parallel PCI 1P Manual de usuario

SIIG

SIIG 1-Port ECP Manual de usuario

SIIG

SIIG ExpressCard/54 CF R/W Manual de usuario

SIIG

SIIG Dual Profile Hi-Speed USB 4-Port PCI Manual de usuario

SIIG

SIIG NN-000032-S1 Manual de usuario

SIIG

SIIG JJ-PCM012-S2 Manual de usuario

SIIG

SIIG 1394 Dual-Port CardBus Manual de usuario

SIIG

SIIG USB 2.0 5-Port PCI Manual de usuario

SIIG

SIIG JU-P40311-S1 Manual de usuario

SIIG

SIIG NN-8CB212-S1 Manual de usuario

SIIG

SIIG JJ-EC2011-S1 Manual de usuario

SIIG

SIIG SATA II-150 PCI Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario