SIIG JJ-E01111-S1 Manual de usuario
1
04-0717B
DP 1-Port RS232 Serial
PCIe with 16950 UART
Quick Installation Guide
Introduction
The DP 1-Port RS232 Serial PCIe with 16950
UART is a high-speed serial card that provides
one additional serial port to your system.
Key Features and Benefits
• PCI Express (x1) single port serial with
128-byte FIFO buffers
• Supports data transfer rate up to 230Kb/s
• Installs in standard height or low profile
chassis with included brackets
System Requirements
•PCI Express equipped system with an
available PCI Express slot
•Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000
2
Package Contents
•DP 1-Port RS232 Serial PCIe with 16950
UART
• Spare enhanced low-profile bracket
• Driver CD
• Quick installation guide
Layout
Figure 1: Layout
Stripe
Serial port pin header
Connector bracket with
9-pin serial port
3
Hardware Installation
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer’ s reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’ s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges. Note: For low profile
chassis, remove the standard height bracket and
install the enhanced low-profile bracket now.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord and remove the
cover from the computer.
3. Remove the slot bracket from an available
PCIe slot.
4
4. To install the card, carefully align the card's
bus connector with the selected PCIe slot on
the motherboard. Push the board down
firmly, but gently, until it is well seated.
5. Replace the slot bracket's holding screw to
secure the card.
6. Replace the computer cover and reconnect
the power cord.
Driver Installation
This section provides information on how to
install the DP 1-Port RS232 Serial PCIe with 16950
UART drivers.
Windows 8 (32-/64-bit) / 7 (32-/64-bit) /
Server 2008 R2
1. Install the board and boot up Windows.
Note: Windows 7 will automatically search
preconfigured driver folders for the proper
driver, this process may take several
minutes to complete. Do not interrupt this
process.
5
2. Insert the driver CD. Close the CD autoPlay
window if prompted.
3. For Windows 8:Click Windows key and R,
type D:\setup.exe, click OK. (Change D: to
match your CD/DVD-ROM drive letter)
For Windows 7 / Server 2008 R2: Click Start.
In the Search programs and files box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
4. At the User Account Control, click Yes.
Skip this step if not prompted.
5. At the Welcome to the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard, click Install.
6. At the Completing the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard,selectRebootnow,thenclickFinish
to complete the installation.
6
Windows Vista (32-/64-bit) / XP (32-/64-bit)
/ Server 2008 (32-/64-bit) / Server 2003 (32-
/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware window,
click Cancel. Skip this step if not prompted.
3. Insert the driver CD. Close CD autoplay
window if prompted.
4. Click Start, Run. Type D:\setup.exe, click
OK. (Change D: to match your CD/DVD
ROM drive letter)
5. At the User Account Control, click Allow.
Skip this step if not prompted.
6. At the Welcome to the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard, click Install.
7. At the Completing the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard,selectRebootnow,thenclickFinish
to complete the installation.
7
Windows 2000
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD. Close AutoPlay if
prompted.
4. Click Start, Run. Type D:\setup.exe, click
OK. (Change D: to match your CD/DVD
ROM drive letter)
5. At the Welcome to the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard, click Install.
6. At the Completing the PLX OXPCIe952
RS-232 Serial/Parallel PCIe Card Setup
Wizard,selectRebootnow,thenclickFinish
to complete the installation.
To Verify Windows Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
8
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows XP / Server 2003 / 2000: Right
click My Computer, click Manage, click
Device Manager.
For Windows Server 2008 / Server 2008 R2:
Right clickComputer, click Manage, double
click Diagnostics, then click Device
Manager.
2. Double click Ports (COM & LPT), and a
PCI Express UART Port ... should be
displayed.
Changing Serial Port Number
Some serial port devices need a specific
communicationport in order to function properly.
If your communication port device works, do not
make any changes.
1. Right click My Computer, click Manage,
then click Device Manager.
2. Double click Ports (COM & LPT), double
click the PCI Express UART Port.
9
3. Click the Settings tab.
4. Click the down arrow next to the COM Port
Number to Use box. Select a communication
port that is not in use, then click OK.
5. Restart your system to take effect.
10
Blank Page
Tabla de contenidos
Otros manuales de Hardware de computadora de SIIG
SIIG
SIIG FireWire Dual-Port CardBus Manual de usuario
SIIG
SIIG Cyber PCI I/O Manual de usuario
SIIG
SIIG US2273 Manual de usuario
SIIG
SIIG NN-8CB212-S1 Manual de usuario
SIIG
SIIG eSATA II ExpressCard Manual de usuario
SIIG
SIIG CyberParallel Dual Manual de usuario
SIIG
SIIG FireWire 800 2-Port ExpressCard/34 Manual de usuario
SIIG
SIIG Low Profile POS 2000RJ Manual de usuario
SIIG
SIIG IO1037 Manual de usuario
SIIG
SIIG CyberSerial ExpressCard Manual de usuario
SIIG
SIIG SATA II PCIe RAID Manual de usuario
SIIG
SIIG JU-2NE012 Manual de usuario
SIIG
SIIG USB 2.0 Bay Reader/Writer+Floppy Manual de usuario
SIIG
SIIG JU-P40412-S1 Manual de usuario
SIIG
SIIG CE-ED0011-S1 Manual de usuario
SIIG
SIIG 1394 Dual-Port CardBus Manual de usuario
SIIG
SIIG JJ-E02111-S1 Manual de usuario
SIIG
SIIG CyberParallel Dual Manual de usuario
SIIG
SIIG NN-E20022-S1 Manual de usuario
SIIG
SIIG SC-SAEE12-S1 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
