SIIG USB SoundWave 5.1 Pro Manual de usuario

USB SoundWave 5.1 Pro

Quick Installation Guide

04-0304A

Introducing the USB SoundWave 5.1 Pro

The USB SoundWave 5.1 Pro brings you cinema-quality 5.1-channel

sound effects. With Built-in Q-SPACETM intelligent 5.1-channel

surround sound system, it turns 2-channel audio into multi-channel

sound.

Features and Benefits

• Compliant with USB 1.1 specification rev. 1.1 and USB Audio

specification rev. 1.0

• Compliant with Microsoft USB Multi-channel driver and

Windows games standards

• Auto-detecting audio stream for DVD, MP3, MP2, WAVE,

Audio CD, MIDI and GM2 formats

• 6-channel Codec support with sample rate operation at 48kHz

• Signal-to-noise ratio (SNR) exceeding 85dB

• Includes WinDVDTM (DVD player) and WinRipTM (MP3

player/encoder) software

• Delivers cinema-quality 5.1 surround sound to all Microsoft

DirectSound and DirectSound3D enabled games

System Requirements

• Pentium II 366 MHz (or equivalent) desktop or notebook

computer with an available USB 1.1/2.0 port

• 32 MB system memory or above

• 100 MB available hard disk space or above

• Speakers (5.1-channel speaker system recommended)

Package Contents

• USB SoundWave 5.1 Pro

• USB cable

• Software CD

• This quick installation guide

Layout

Figure 1: Buttons and LEDs

Buttons:

• MUTE: Press this button to enable/disable sound

• SUR: Press this button to enable/disable 5.1-channel surround

sound

• MIC: Press this button to enhance microphone output signal if

needed

LEDs:

• PWR: LED ON indicates normal operation; LED FLASHING

indicates unit is in Mute mode; LED OFF indicates unit is

unplugged from the USB port.

• SUR: LED ON indicates 5.1-channel surround sound is

enabled; LED OFF indicates surround sound is disabled

Note: The SUR LED will not be lit when software encoded audio

surround sound is played.

• MIC: LED ON indicates the microphone enhanced mode is

enabled; LED OFF indicates microphone enhanced mode is not

used.

MUTE

SUR

MIC PWR

SUR

MIC

Figure 2: Connectors

• C/LFE: Orange connector for Center/Subwoofer speakers.

General design of 5.1 speakers for PC is plugging center

speaker cable to subwoofer, then plugging subwoofer cable to

the C/LFE connector. However, if your center speaker and

subwoofer must be individually plugged, buy a two-to-one

converter and plug it into C/LFE jack.

• Rear: Black connector for Rear Right and Rear Left speakers.

• Front: Green connector for Front Right and Front Left

speakers. This connector can also be used to connect

headphones.

• MIC/Line: Blue connector for Microphone or Line-in devices

such as MP3 players, radio sets, CD/DVD players and many

more.

• USB Connector: Connect one end of the provided USB cable

to the SoundWave 5.1 Pro and the other end to a USB port on

your desktop or laptop computer.

Hardware Installation

Connect your speaker system plus any other input devices to the

USB SoundWave 5.1 Pro. Please refer back to the Layout section for

connection information if needed.

After making all speaker/device connections, plug one end of the

provided USB cable into the USB SoundWave 5.1 Pro's USB

connector, then plug the other end into your system's USB port.

C/LFE Rear Front USB

MIC/Line

Software Installation

This section provides information on how to install the

USB SoundWave 5.1 Pro's drivers and the provided software.

Windows 98SE:

1. At the Add New Hardware Wizard window, click Next.

2. Select Search for the best driver for your device

(Recommend), then click Next.

3. Insert your Windows 98SE Installation CD, select CD-ROM

drive, uncheck the other boxes, then click Next.

4. Click Next, Next, then Finish.

5. Repeat steps 1-4 to install the USB audio device.

6. Remove the Windows 98SE Installation CD and restart

Windows to complete installation.

Windows ME:

1. At the Add New Hardware Wizard, insert your Windows ME

Installation CD. Select Automatic search for a better driver

and click Next.

2. Click Finish.

3. Remove the Windows ME Installation CD and restart

Windows to complete installation.

Windows 2000/XP Installation

Windows 2000/XP will automatically detect and install the correct

drivers for the USB SoundWave 5.1 Pro.

To verify successful installation:

1. Check Device Manager to verify successful driver installation.

Windows 98SE/ME: From the main desktop, right click My

Computer, click Properties,then click Device Manager.

Windows 2000/XP: Right click My Computer, click Manage,

then click Device Manager.

2. Double click Sound, video and Game controllers and USB

Audio Device should be displayed.

3. Double click Universal Serial Bus controllers and USB

Composite Device should be displayed.

Software Utilities

The bundled CD contains three software: WinDVD, WinRip, and

Speaker Tester. You can install above applications as needed.

Please note that the software's serial numbers are located on top of

the software CD envelope.

WinDVD Installation

WinDVD is a simple to use DVD player combining all the features

you would expect to find in a standard consumer DVD player, in

addition to some very advanced functionality, such as full VCD 2.0

support, full precision video decode, a choice of user interfaces and

video display options.

1. Insert the software CD and auto-run should start

automatically. If auto-run does not start, click Start then Run.

Type in D:\auto.exe and click OK. (Change D: to match your

CD-ROM drive letter)

2. Click WinDVD, then click Install. Follow the on-screen

instructions to complete installation.

After WinDVD installation is complete, return to the WinDVD

installation screen and click User's Guide to view the user's manual.

WinRip Installation

WinRip is a state-of-the-art software application that provides you

with a complete audio playback and recording environment. It

supports various audio formats such as MP3, WAVE, MIDI, Audio

CD and more.

1. Insert the software CD and auto-run should start

automatically. If auto-run does not start, click Start then Run.

Type in D:\auto.exe and click OK. (Change D: to match your

CD-ROM drive letter)

2. Click WinRip, then click Install. Please key in serial number

"N9J9JEX9M9R59ER" . Follow the on-screen instructions to

complete installation.

After WinRip installation is complete, return to the WinRip

installation screen and click Help to view the user's manual.

Speaker Tester

Speaker Tester allows you to diagnose common surround sound

speaker setups. The utility is run directly from the software CD.

1. Insert the software CD and auto-run should start

automatically. If auto-run does not start, click Start then Run.

Type in D:\auto.exe and click OK. (Change D: to match your

CD-ROM drive letter)

2. Click Speaker Tester.

3. Choose which diagnostic test to run; 2 Channel, 4 Channel or

5.1 Channel. You can also check on the output of an

individual speaker channel by clicking on it graphical

representation.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers! Simply

visit our web site at www.siig.com and click SUPPORT. Our online

support database is updated daily with new drivers and solutions.

The answers to your problems could be just a few clicks away.

Return Merchandise Authorization (RMA)

SIIG warrants to the original buyer of the product that the hardware

is free of defects in materials and workmanship for a period of one,

two or five years from the date of purchase. If your product fails to

be in good working order during the warranty period, you may

return it to SIIG for repair or replacement at SIIG's option.

To return the product, you need to follow these steps.

Step 1: Contact SIIG's RMA Department

To obtain an RMA number, SIIG's RMA Department can be reached

by phone at (510)413-5333 or fax at (510)657-5962 or email at

[email protected]. In order to issue an RMA number, the product

serial number is required. This number can be found on the side of

the box and on the back of the product.

Step 2: Complete the RMA form

• Fill out your Return Merchandise Authorization (RMA) form,

and include it in the package with the product.

• Properly pack the product for shipping. All software, cable(s)

and other accessories that came with the original package

must be included.

• Clearly write your RMA number on the top of the returned

package and on the accompanying RMA form.

SIIG will refuse to accept any shipping package, and will not

be responsible for a product returned without an RMA number

posted on the outside of the shipping carton.

Step 3: Ship the Product

You are responsible for the cost of shipping back to SIIG at the

following address:

SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIG will ship the repaired or replaced product via UPS Ground or

US Mail at no cost to you.

UK Warranty & Support Information

The 5 year warranty supplied with this product is offered by SIIG,

Inc. If you should happen to encounter any problems with this

product, please follow the procedures below.

1. If it is within the first year of purchase, please return product

to the outlet you purchased from.

2. If your product is between 2 and 5 years old from date of

purchase, please contact SIIG using the contact details below.

For UK Technical Support

Telephone: +44 (0) 1255 687503

Fax: +44 (0) 1255 687501

Email: [email protected]

Website: http://www.siig.uk.com

PRODUCT NAME MODELNUMBER

USB SoundWave 5.1 Pro CE0704

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATINGENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

USB SoundWave 5.1 Pro is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered

trademarksofMicrosoftCorporation. PentiumisaregisteredtrademarkofIntelCorporation. Other

names used in publication are for identification only and may be trademarks of their respective

companies.

Tabla de contenidos

Otros manuales de Adaptador de SIIG

SIIG

SIIG US2253 Manual de usuario

SIIG

SIIG USB 2.0 to VGA Pro Manual de usuario

SIIG

SIIG US2322 Manual de usuario

SIIG

SIIG SC-SA0512-S1 Manual de usuario

SIIG

SIIG SATA-to-IDE Adapter Manual de usuario

SIIG

SIIG JU-NE0711-S1 Hoja de información del producto

SIIG

SIIG SC-M20211-S1 Manual de usuario

SIIG

SIIG JU-H30612-S1 Hoja de información del producto

SIIG

SIIG RS232 Serial Manual de usuario

SIIG

SIIG ID-SB0111-S1 Hoja de información del producto

SIIG

SIIG JU-NE0211-S1 Manual de usuario

SIIG

SIIG YN6181 Manual de usuario

SIIG

SIIG AC-PW0N12-S1 Manual de usuario

SIIG

SIIG JU-DV0211-S1 Manual de usuario

SIIG

SIIG Aluminum Mini DisplayPort 1.2 to VGA Adapter... Manual de usuario

SIIG

SIIG Wireless-N Mini USB Wi-Fi Adapter Manual de usuario

SIIG

SIIG CN2502 Manual de usuario

SIIG

SIIG SATA-to-IDE Adapter Manual de usuario

SIIG

SIIG JU-AV0012-S1 Manual de usuario

SIIG

SIIG CB-TC0611-S1 Hoja de información del producto

SIIG

SIIG USB 3.0 to SATA 6Gb/s Adapter Manual de usuario

SIIG

SIIG CE-H23R11-S1 Manual de usuario

SIIG

SIIG JU-000071-S1 Manual de usuario

SIIG

SIIG CE-HM0021-S1 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario