SIIG CyberParallel PCIe Manual de usuario

CyberParallelPCIe

Quick Installation Guide

04-0422C

Introducing the CyberParallel PCIe

The CyberParallel PCIe high-speed parallel adapter

providesoneadditionalparallelporttoyourPCIExpress

enabled system.

Features and Benefits

•Compliant with PCI Express Base Specification

Revision 1.0a

•PCI Express 1-lane (x1) parallel adapter works with

PCI Express slots with different lane width

•Full support for Windows-based software

•Supports EPP/ECP and SPP (standard) parallel

port modes

System Requirements

•PCI Express enabled system with an available PCI

Express slot

•Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP

(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000

PackageContents

•CyberParallel PCIe adapter

• Spare enhanced low-profile bracket

• Driver CD

• Quick installation guide

Parallel Port

Layout

Figure 1. Layout

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer’s case for a few

seconds. Avoid any contact with internal parts and

handle cards only by their external edges. Note: For low

profile chassis, remove the full height bracket and install the

enhanced low profile bracket now.

1. Turn OFF the power to your computer and any

other connected peripheral devices.

2. Unplug the power cord and remove the cover from

the computer.

3. Remove the slot bracket from an available PCI

Express slot.

4. To install the card, carefully align the card's bus

connector with the selected PCI Express slot on the

motherboard. Push the board down firmly, but

gently, until it is well seated.

5. Replace the slot bracket's holding screw to secure

the card.

6. Replacethecomputercoverandreconnectthe power

cord.

Driver Installation

This section provides information on how to install the

CyberParallel PCIe drivers.

Windows 7 (32-/64-bit)

1. Install the board and boot up Windows.

Note: Windows 7 will automatically search

preconfigured driver folders for the proper driver,

this process may take several minutes to complete.

Do not interrupt this process.

2. Right click Computer, click Manage, click Device

Manager.

3. Insert the driver CD. Right click PCI Parallel Port,

click Update Driver Software.

4. Click Browse my computer for driver software.

5. Type D:, then click Next. (Change D: to match your

CD/DVD-ROM drive letter)

6. At Windows has successfully updated your driver

software, click Close to complete the installation.

Windows Vista (32-/64-bit)

1. Install the board and boot up Windows.

2. At the Found New Hardware window, insert the

driver CD, click Locate and install driver software

(recommended), then click Continue.

3. Click Don't search online. Click Next.

4. Click Close to complete the installation.

Windows XP (32-bit ) / Server 2003 (32-bit)

1. Install the board and boot up Windows.

2. At the Found New Hardware Wizard, insert the

driver CD.

For XP w/SP1 or earlier / Server 2003: go to step #2.

For XP w/SP2 or later / Server 2003 w/SP1 or later:

select No, not this time, click Next.

3. Select Install the software automatically

(Recommended,then click Next.

4. Click Finish to complete the installation.

Windows XP (64-bit) / Server 2003 (64-bit)

1. Install the board and boot up Windows.

2. At the Found New Hardware Wizard, insert the

driver CD.

For XP: go to step #2.

For XP w/SP1 or later / Server 2003:select No, not this

time, click Next.

3. Select Install the software automatically

(Recommended,then click Next.

4. Click Continue Anyway, then click Finish to

complete the installation.

Windows Server 2008 (32-bit)

1. Install the board and boot up Windows.

2. At the Found New Hardware window, click Locate

and install driver software (recommended).

3. Insert the driver CD.

4. Click Don't search online.

5. Click I don't have the disc. Show me other options.

6. Click Browse my computer for driver software

(advanced).

7. Type D:, then click Next. (Change D: to match your

CD/DVD-ROM drive letter)

8. Click Close to complete the installation.

Windows Server 2008 (64-bit)

1. Install the board and boot up Windows.

2. At the Found New Hardware window, click Locate

and install driver software (recommended).

3. Insert the driver CD.

4. Click I don't have the disc. Show me other options.

5. Click Browse my computer for driver software

(advanced).

6. Type D:, then click Next. (Change D: to match your

CD/DVD-ROM drive letter)

7. Click Close to complete the installation.

Windows 2000

1. At the Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended), then click Next.

3. Check Specify a location, uncheck the other options

and click Next.

4. Insert the driver CD, type in D:\2000, then click OK.

(Change D: to match your CD/DVD-ROM drive

letter)

5. Click Next, then click Finish to complete the

installation.

To Verify Windows Installation

1. Check in Device Manager to verify installation.

For Windows 7: Right click Computer, click Manage,

then click Device Manager.

For Windows Vista: Right click Computer, click

Manage,click Continue,thenclickDeviceManager.

For Windows XP / Server 2003 / 2000: Right click My

Computer, click Manage, click Device Manager.

For Windows Server 2008: Right click Computer, click

Manage,doubleclickDiagnostics,thenclickDevice

Manager.

2. Click on the +(plus sign) in front of Ports (COM &

LPT), and a SIIG CyberPro Parallel port ... should

be displayed.

Changing Parallel Port Number

Some parallel port devices need a specific LPT in order

to function properly. If your device works, do not make

any changes.

1. Right click My Computer, click Manage, then click

Device Manager.

2. Click on the +(plus sign) in front of Ports (COM &

LPT), double click the SIIG CyberPro Parallel port

you want to change.

3. Click the Port Settings tab.

4. Click the down arrow next to the LPT Port Number

box, then select a parallel port that is not in use.

5. Click OK to save the changes.

Technical Support and Warranty

QUESTIONS? SIIG’sOnline Support hasanswers! Simplyvisit our

web site at www.siig.com and click Support. Our online support

database is updated daily with new drivers and solutions. Answers

toyour questions could bejust a few clicksaway. You can also submit

questions online and a technical support analysts will promptly

respond.

SIIGoffers alifetime manufacturerwarrantywiththisproduct. Please

see our web site for more warranty details. If you encounter any

problems with this product, please follow the procedures below.

A) If it is within the store's return policy period, please return the

product to the store where you purchased from.

B) Ifyourpurchase has passed thestore's return policy period,please

follow these steps to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, click Support, then RMA to submit a

request to SIIG RMA. Your RMA request will be processed, if the

product is determined to be defective, an RMA number will be

issued.

Step 2: After obtaining an RMA number, ship the product.

•Properly pack the product for shipping. All software, cable(s)

and any other accessories that came with the original package

must be included.

•Clearly write your RMA number on the top of the returned

package. SIIG will refuse to accept any shipping package, and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

•You are responsible for the cost of shipping. Ship the product

to the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

RMA #:

•SIIG will ship the repaired or replaced product via Ground

in the U.S. and International Economy outside of the U.S. at

no cost to the customer.

CyberParallelPCIeisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarksofSIIG,

Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names

used in this publication are for identification only and may be trademarks of their respective owners.

PRODUCT NAME

CyberParallel PCIe

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

Phone: 510-657-8688

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity

solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,

and legacy I/O adapters) that bridge the connection between Desktop/

Notebook systems and external peripherals. SIIG continues to grow by

adding A/V and Digital Signage connectivity solutions to our extensive

portfolio. Allcentered around thedistribution and switchingof A/V signals

overCAT5/6,theseproductsincludematrixswitches, distribution amplifiers,

extenders, converters, splitters, cabling, and more.

SIIG is the premier one-stop source of upgrades and is committed to

providing high quality products while keeping economical and competitive

prices. High-quality control standards are evident by one of the lowest

defective return rates in the industry. Our products offer comprehensive

user manuals, user-friendly features, and most products are backed by a

lifetime warranty.

SIIG products can be found in many computer retail stores, mail order

catalogs, and e-commerce sites in the Americas, as well as through major

distributors, system integrators, and VARs.

Tabla de contenidos

Otros manuales de Adaptador de SIIG

SIIG

SIIG JU-000061-S1 Manual de usuario

SIIG

SIIG JU-000071-S1 Manual de usuario

SIIG

SIIG SATA-to-IDE Adapter Manual de usuario

SIIG

SIIG CE-HM0021-S1 Manual de usuario

SIIG

SIIG JU-HM0112-S1 Manual de usuario

SIIG

SIIG Wireless-N CardBus Adapter Manual de usuario

SIIG

SIIG US2322 Manual de usuario

SIIG

SIIG USB-to-PS/2 Manual de usuario

SIIG

SIIG JU-VG0311-S1 Manual de usuario

SIIG

SIIG JU-AV0012-S1 Manual de usuario

SIIG

SIIG JU-NE0211-S1 Manual de usuario

SIIG

SIIG AC-PW0N12-S1 Manual de usuario

SIIG

SIIG USB 3.0 to DisplayPort Adapter Manual de usuario

SIIG

SIIG Wireless-N Mini USB Wi-Fi Adapter Manual de usuario

SIIG

SIIG JU-NE0B11-S1 Manual de usuario

SIIG

SIIG JJ-P20511-S3 Manual de usuario

SIIG

SIIG CyberParallel Dual PCIe Manual de usuario

SIIG

SIIG USB 3.0 to SATA 6Gb/s Adapter Manual de usuario

SIIG

SIIG Aluminum Mini DisplayPort 1.2 to VGA Adapter... Manual de usuario

SIIG

SIIG CE-AD0012-S1 Manual de usuario

SIIG

SIIG CB-TC0611-S1 Hoja de información del producto

SIIG

SIIG JU-DV0211-S1 Manual de usuario

SIIG

SIIG NN26 Series Manual de usuario

SIIG

SIIG SC-SA0512-S1 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario