Siemens GW-23 Manual de usuario

GW-23

Gateway GW-23

Technical Manual

Document No. e1476

Edition 03.99

Supersedes -

Manual Hardware Installation

Section 2

Cerberus Division

Table of contents

e1476.doc Data and design subject to change without notice. Supply subject to availability

Table of contents

1Introduction _________________________________1

1.1 Scope of this document _________________________________________ 2

1.2 Related publications ____________________________________________ 2

2Product description ___________________________3

2.1 The CPU board_________________________________________________ 3

2.2 The connection board___________________________________________ 4

2.3 Power supervision______________________________________________ 6

3connection cables ____________________________7

3.1 Connection GW-23 - ISDN adapter_________________________________ 7

3.2 Connection GW-23 - Modem______________________________________ 8

3.3 Connection to Cerberus subsystem _______________________________ 8

3.4 Connection layout ______________________________________________ 9

4Technical data ______________________________10

Cerberus Division

Introduction

e1476.doc Data and design subject to change without notice. Supply subject to availability

1 Introduction

The GW-23 interfaces both the peripheral control units and a virtual digital I/O sub-

system to a structured network such as:

•X.25 via X.28 asynchronous RS-232 PAD

•X.25 via ISDN channel D and asynchronous RS-232 terminal adapter

•Ethernet TCP/IP protocol

Also, a dial-up, switched modem connection is supported as backup of any of the

above listed solution.

The GW-23 gateway is composed by one CPU board, one optional ethernet adapter

and one optional I/O board. The gateway is then installed on a connection board,

where the serial and I/O connections are made available.

Each GW-23 can manage up to

4 serial lines;

1 ethernet 10baseT connection;

up to 16 digital inputs and 8 digital outputs

Note: The optional I/O espansion is supported only with special version of manage-

ment station software; this board is not documented in this edition of the GW-

23 technical manual.

The four serial lines can be connected to

one RS-232 adapter for X.28 or ISDN-D;

one full modem;

two to Cerberus control units, supporting Cerban protocol

Fig. 1-1: GW-23

Cerberus Division

Introduction

2[14]Data and design subject to change without notice. Supply subject to availability

1.1 Scope of this document

This manual is intended as a guide for planning, installation and service personnel of

Cerberus danger management systems which use GW-23 device.

All necessary information to install a GW-23 gateway are listed in this manual.

1.2 Related publications

The following documents could be useful in dealing with GW-23 gateway and under-

standing how it relates to other pieces of the LMS network:

LMSmodular User manual e1108

LMSmodular V2.2 Configuration guide manual e1109

LMSmodular V2.2 Configuration reference manual e1252

LMSmodular V2.2 Installation Manual e1116

LMSmodular V2.4 Update Manual e1691

Cerberus Division

Product description

e1476.doc Data and design subject to change without notice. Supply subject to availability

2 Product description

2.1 The CPU board

The CPU board is the main board (CD98600).

Fig. 2-1- The CPU board

On this board there are:

•the CPU, RAM, UARTs and other electronic components

•four dip switch blocks (SW1 - SW4), used only for the board factory setup

•one reset push-button, used to reset the board

•one service push-button, to send the service signal to the Neuron Chip

•four sets of two LEDs (TX green and RX red); these LEDs show the status of

UARTs RX/TX lines

•six LEDs (LD1-LD6 green, yellow, and red) used for diagnostic purposes.

The six diagnostic LEDs marked LD1, LD2 and LD3 have the following meaning:

ON OFF Blinking

LD1 Vitality

(green) Firmware vitality trouble Firmware vitality trouble OK

LD2 Service

Not used

(yellow)

LD3 Identification

(yellow) GW-23 not yet identified from

control center (GW-10). OK -

LD4

Download

(yellow)

-OK Download in progress

LD5

RAM error

(red)

Internal diagnostic error OK Internal diagnostic error

LD6

Download error

(red)

The GW-23 cannot proceed. An error

occurred in the download OK The GW-23 cannot proceed.

An error occurred in the download

Fig. 2-2- The I/O board

All dip-switches must be left to OFF.

The board also includes some jumpers: do not modify the factory setting.

LD1 Vitality

LD3 Identification

LD5 RAM error

RX1

TX1

RX2

TX2

RX3

TX3

RX4

TX4 SW1

SW2

SW3

SW4

Reset

Cerberus Division

Product description

4[14]Data and design subject to change without notice. Supply subject to availability

2.2 The connection board

The connection board (CD96812) has two connectors to insert the CPU and I/O

board in.

On the board there are two DB9 D connectors for the two serial ports (Com 3 and 4).

COM 1 and 2 are accesible through screw connectors - only the TX, RX and GND

signals are available. They are used to connect the Cerberus control panels.

On the same connection board there is the power supply block. It has three pins: the

central one is the ground, the two laterals are marked + and -. You must connect here

a 13.8 Vdc voltage source.

Cerberus Division

Product description

e1476.doc Data and design subject to change without notice. Supply subject to availability

COM 4

Network adapter

Power

(13.8 V)

COM 1

Cerban 1

COM 2

Cerban 2

LON

COM3

Dial-upmodem

I/O connector

I/O expansion

board

CPU board

Component side→

GND

Fig. 2-3- The connection board

Cerberus Division

Product description

6[14]Data and design subject to change without notice. Supply subject to availability

2.3 Power supervision

The power supervision board is reporting the following information on a set of LEDs:

Red ⊗⊗ Tamper: normally OFF, it indicates tamper condition

Yellow ⊗Low Battery: normally OFF, it is ON if voltage drops below 10.8V±0,5V

Yellow ⊗Fuse Battery: normally OFF, if ON, it indicates that fuse (T3.75A)

is broken

Yellow ⊗Power Fault: normally OFF, if ON, it indicates a fault in the supply unit

Green ⊗Main: normally ON, if OFF, it indicates 220 Vac missing

Green ⊗Power ON: normally ON

Tabla de contenidos

Otros manuales de Puerta de Siemens

Siemens

Siemens SpeedStream 6500 Series Manual de usuario

Siemens

Siemens WTT563 Series Manual de usuario

Siemens

Siemens SpeedStream 6500 Series Manual de usuario

Siemens

Siemens NK8237 MP4.81-02 Guía rápida

Siemens

Siemens WTT568 Series Manual de usuario

Siemens

Siemens FDCW241 Guía

Siemens

Siemens ProtoAir FPA-W44 Guía del usuario

Siemens

Siemens FDCW221 Manual de usuario

Siemens

Siemens SIMATIC PN/J1939 LINK Manual de usuario

Siemens

Siemens RUGGEDCOM WIN5151 Manual de usuario

Siemens

Siemens OCT200.KNBA Manual de usuario

Siemens

Siemens SIRIUS 3RK3141 Series Manual de usuario

Siemens

Siemens IE/PB LINK PN IO Manual de usuario

Siemens

Siemens SIMATIC NET IE/WSN-PA Link Guía del administrador

Siemens

Siemens NK8225 Manual operacional

Siemens

Siemens SIMATIC NET IE/WSN-PA Link Guía del administrador

Siemens

Siemens Gigaset SE567 Manual de usuario

Siemens

Siemens SIMATIC RTLS Series Guía de aplicación

Siemens

Siemens Advance Network Gateway Manual de usuario

Siemens

Siemens SIMATIC PN/M-Bus LINK Manual de usuario

Siemens

Siemens SIMATIC FDE Manual de usuario

Siemens

Siemens SIMATIC IOT2050 Manual de usuario

Siemens

Siemens SMG 71 Manual de usuario

Siemens

Siemens SIMATIC FDE Gateway V1.1 Documento técnico

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario