Siemens TSM-1 Manual de usuario

Fire Safety

INTRODUCTION

The Model TSM-1 Test Switch Module from Siemens

Building Technoliges, Inc. is a key activated momen-

tary switch for use with intelligent duct detectors on

the MXL System. It is used in conjunction with a TRI,

whose CSG-M usage is set to TEST. When the TRI

senses the TSM-1 switch closure, it will cause its

associated intelligent duct detector to go into alarm.

This alarm condition will cause all logic associated

with the duct detector to activate. The TSM-1 is

mounted on a switch plate and can be installed in a

single gang box.

Remove all power from the system until the

installation is complete and ready for testing.

All work of any kind shall be performed to meet

the requirements of all local and national codes

and/or standards required by the authority hav-

ing jurisdiction.

WIRING INSTRUCTIONS

Refer to the wiring diagrams in Figures 2 and 3

and wire the addressable interface module

according to the appropriate operation for your

system.

Note: The recommended wire size is as follows:

18 AWG minimum

14 AWG maximum

POWER LIMITED WIRING FOR THE TSM-1

TEST SWITCH MODULE

In compliance with NFPA70—National Electrical

Code, all power limited fire protective signaling

conductors must be separated by a minimum of ¼

inch from all of the following items located within an

outlet box:

• Electric light

• Power

• Class 1 or non-power limited fire protective

signaling conductors

INSTALLATION

1. Remove the module from its protective bag.

Mount the TSM-1 in a user supplied standard

single gang mounting box (1½ in deep is

recommended). Refer to Figure 1.

2. Terminate all field wires to the TSM-1 as required

for your application. Refer to the connection

diagrams shown in Figures 2 and 3.

3. Attach the switch frame to the box.

4. Check that jumper JP1 is NOT installed. (JP1 is

not used in this application.)

5. Attach the keyswitch connector to its mating plug

on the bottom of the circuit board.

6. Insert the face plate and attach the cover plate

with the two screws provided.

Note: A yellow and green LED are included in the

kit. Do not use them in this application.

P/N 315-098285-8

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2185 Derry Road West

Mississauga, Ontario L5N 7A6 Canada

Installation Instructions

MODELTSM-1

Test Switch Module

PROGRAMMING

1. Use the FPI-32 Programmer/Tester to program

the TRI to the desired address. Select STATUS

as the usage.

2. To operate the TSM-1 LED by the TRI-R relay

contacts:

In the CSG-M, configure the TRI by setting its

usage to TEST and assign the detector’s

address to the TRI-R.Add a logic function with

the intelligent detector that will be tested as the

input, and assign the output as the TRI-R. Refer

to Figure 2.

3. To operate the TSM-1 LED by the air duct

detectors:

In the CSG-M, configure the TRI by setting its

usage to TEST.Add a logic function with the

intelligent detector that will be tested as the

input, and assign the output as the fan shutdown

control operated by the air duct detector. Refer to

Figure 3.

Figure 1

TSM-1 Assembly

OPERATION

Reset the MXL System until SYSTEM NORMAL is

displayed on the panel. Insert the key into the

manual keyswitch input point on the TSM-1.Activate

the momentary switch by turning the key to the right.

When the TSM-1 keyswitch is activated, the super-

vised switch input of the TRI-R is closed. The TRI-R

activation is received by the MXL panel. The MXL

panel then sends a reduced alarm threshold to the

detector through the TEST usage of the TRI-R. This

causes the detector to alarm.

When the detector goes into alarm and sends alarm

data back to the MXLpanel, the MXL panel sends

command data to the TRI-R or air duct to close the

relay, which activates the fan controller through the

logic function. The MXLpanel sends a signal to the

intelligent detector, turning on the red LED in both the

detector and the TSM-1, indicating the detector is in

alarm.

Reset the system. The MXLSystem will restore the

detector’s alarm threshold and display SYSTEM

NORMAL on the panel.

CAUTION:

The TSM-1 switch does not perform all of the required smoke detector tests as speci-

fied in NFPAStandard 72. Please refer to the instructions that accompany the smoke

detector for the complete test requirements.

Figure 2

TSM-1 Interface to MXL System

TSM-1 LED operated by the TRI-R relay contacts

From MXL

ALD Loop

Earth

Ground

Switch

Input LED

TSM-1

TRI-R

End of Line Device

for TRI-R

3.6K, 1/4W,

P/N 140-820185

24 VDC @ 20mA (max)

From MMB-2, TB5

or MMB-3, TB9

Terminals 9-12

or PSR-1, TB3

Terminals 3-6

or UL Listed

Power Supply

To Air Duct

Detector or next

device on loop

Switch contact rating:

24VDC @10mA (min.)

Figure 3

TSM-1 Interface to MXL System

TSM-1 LED operated by the Air Duct Detector

NOTES:

1. For use only with Air Ducts with an incorporated relay.

2. Refer to the TRI Installation Instructions, P/N 315-096242, for specific interface module wiring requirements.

3. Refer to the AD-11PR, AD-11XPR Installation Instructions, P/N 315-095659, or the AD-3I/-3ILP Installation Instructions,

P/N 315-093234, for specific duct detector wiring requirements, as applicable.

From MXL

ALD Loop

Earth

Ground

Switch

Input LED

TSM-1

TRI-R

End of Line Device

for TRI-R

3.6K, 1/4W,

P/N 140-820185

To Air Duct Detector

(See Detector Installation

Instruction for Remote

Alarm Indicator

Connection)

To Fan

Shutdown

Control

To Air Duct Detector

or next device on loop

Switch contact rating:

24VDC @10mA (min.)

NOTES:

1. For use only with Air Ducts without an incorporated relay.

2. Refer to the TRI Installation Instructions, P/N 315-096242, for specific interface module wiring requirements.

3. Refer to the AD-11P Installation Instructions, P/N 315-095659, or the AD-3I/-3ILP Installation Instructions, P/N 315-

093234,

for specific duct detector wiring requirements, as applicable.

P/N 315-098285-8

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2185 Derry Road West

Mississauga, Ontario L5N 7A6 Canada

Otros manuales de Unidad de control de Siemens

Siemens

Siemens FCI2011-U1 Guía

Siemens

Siemens SINUMERIK 840D sl Manual del propietario

Siemens

Siemens SIRIUS 3RV2.2 Manual de usuario

Siemens

Siemens LOGO! CMK2000 Manual de usuario

Siemens

Siemens 3VT9300-4WA30 Manual de usuario

Siemens

Siemens PROFIBUS CP 1542-5 Manual de usuario

Siemens

Siemens 6SE7024-1EP85-0AA1 Manual de usuario

Siemens

Siemens TM Timer DIDQ Guía de inicio rápido

Siemens

Siemens SIMATIC PCS 7 Manual de usuario

Siemens

Siemens SINUMERIK 828D PPU Series Manual de usuario

Siemens

Siemens SINUMERIK 840D Manual de lista de piezas

Siemens

Siemens SIRIUS 3RW5 series Documento técnico

Siemens

Siemens 7KT1 908 Manual de usuario

Siemens

Siemens SIMOCODE pro 3UF7400-1AA00-0 Manual de usuario

Siemens

Siemens LGI16 Series Manual de usuario

Siemens

Siemens 3SB5 Manual de instrucciones

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC NET SCALANCE W760 Series Hoja de instrucciones

Siemens

Siemens SIRIUS 3RA2130-4 A3 Series Manual de usuario

Siemens

Siemens SINUMERIK Series Manual de lista de piezas

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens 3RK1408-8K.00-0AA2 Manual de usuario

Siemens

Siemens LMV 5 Series Manual de usuario

Siemens

Siemens SINAMICS SM120 Instrucciones de funcionamiento

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario