Siemens SiPass Driver Manual de usuario

Installation Instructions

Document No. 565-722

August 2, 2013

SiPass Driver for PXC Modular and PXC-36

Item Number: 565-722, Rev. BA

Page 1 of 2

These installation instructions cover the connection of

the Siemens SiPass Driver to the SiPass system

only.

For hardware installation of the PXC Modular, see

the

PXC Modular Series Installation Instructions

(553-638).

For hardware installation of the PXC-36, see the

PXC Compact 36 Installation Instructions

(553-504).

Product Description

The Siemens SiPass Driver enables communication

between the APOGEE® Automation System and the

Siemens SiPass system.

Product Numbers

License

LSM-INT-SBTSPSS

License to enable the Siemens SiPass

Driver on PXC Modular or PXC-36

hardware.

PXC Modular Series

PXC00-PE96.A

PXC Modular, Ethernet or RS-485

ALN, 96 FLN nodes

PXC00-E96.A

PXC Modular, BACnet/IP or MS/TP

ALN, 96 FLN nodes

PXC100-PE96.A

PXC Modular, Ethernet or RS-485

ALN, 96 FLN nodes, TX-I/O module

support

PXC100-E96.A

PXC Modular, BACnet/IP or MS/TP

ALN, 96 FLN nodes, TX-I/O module

support

PXX-485.3

Expansion Module, three RS-485 FLN

connections

PXC Compact Series

PXC36-PE.A

PXC Compact, 36 point, Ethernet/IP or

RS-485 ALN

PXC36-E.A

PXC Compact, 36 point, BACnet/IP or

MS/TP ALN

Accessories

538-670

Trunk Interface II, 115V

538-675

Trunk Interface II, 230V

536-004

RS-232 Cable

Caution Notation

CAUTION

Equipment damage or loss of data may

occur if you do not follow a procedure as

specified.

Expected Installation Time

30 minutes

Required Tools and Materials

Flat-blade screwdriver (1/8-inch blade width).

Wire strippers.

Cabling and connectors. See the

Connecting the

Driver to the

SiPass System

section.

CAUTION

Always wear an electro-static discharge

(ESD) wrist strap and discharge

accumulated static before touching field

panel components.

Document No. 565-722

Installation Instructions

August 2, 2013

Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as

design improvements are introduced. APOGEE, Insight, and SiPass are registered trademarks of Siemens Industry, Inc. Other product or

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

USA

Tel. 1 + 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com.

Document No. 565-722

Printed in the USA

Page 2 of 2

Prerequisites

Driver hardware is installed according to its

respective installation instructions.

FLN termination blocks are installed.

One 115V or 230V receptacle (depending on

device) is available to power the Trunk Interface

II.

Ethernet infrastructure is installed.

Depending on the type of installation, other

prerequisites may have to be completed.

Connecting the Driver to the SiPass

System

Follow these steps to connect the driver to the SiPass

System:

1. Install the Trunk Interface II per the diagram in

Figure 1.

2. Connect cables per the diagram in Figure 1.

3. Plug in the power supply for the Trunk Interface II

per the diagram in Figure 1.

Figure 1: Connecting the Driver to the SiPass System.

Table 1. Wiring Pin-outs for RS-232 Cable

(P/N 536-004).

Trunk Interface

(DB-25 Male)

SiPass

(9-pin Female)

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens RUGGEDCOM RS400 Manual de usuario

Siemens

Siemens SIMATIC FM 453 Manual de usuario

Siemens

Siemens PS-35 Manual de usuario

Siemens

Siemens SIMATIC 500 Series Manual

Siemens

Siemens ANT792-6MN Guía del administrador

Siemens

Siemens CUA20 Manual de usuario

Siemens

Siemens MOBY I ASM 421 Manual de lista de piezas

Siemens

Siemens Simatic S7-1500/ET 200MP Documento técnico

Siemens

Siemens MICROMASTER Vector 6SE32 Manual de usuario

Siemens

Siemens S-60 Manual de usuario

Siemens

Siemens VAG60 Series Manual de usuario

Siemens

Siemens SINUMERIK 810D Guía de inicio rápido

Siemens

Siemens SINUMERIK 808D Manual de usuario

Siemens

Siemens VAI60.15-15 Manual de usuario

Siemens

Siemens 3RK2 Series Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SINUMERIK 828D Turning Manual de lista de piezas

Siemens

Siemens VSA-1 Manual de usuario

Siemens

Siemens IM 155-6 PN ST Documento técnico

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens SIMOCODE pro Manual de usuario

Siemens

Siemens MJ-XL Manual de usuario

Siemens

Siemens SIDOOR ATD4 W Series Guía del usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario