Siemens SIMATIC ET 200SP TM ECC 2xPWM ST Manual de usuario

SIMATIC

ET 200SP

Technology module TM ECC

2xPWM ST (6FE1242-6TM10-

0BB1)

Manual

04/2018

A5E42681298B

-AA

Preface

Documentation guide

Product overview

Wiring

Configuring/address space

Programming

Interrupts/diagnostic

messages

Technical specifications

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E42681298B-AA

Ⓟ

05/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury

may

result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 3

Preface

Purpose of the documentation

This manual contains module-specific information on wiring, diagnostics as well as the

technical specifications of the technology module.

General information on installation and commissioning of the ET 200SP is available in the

ET 200SP System Manual.

Conventions

Please take into account the notes marked as follows:

Note

A note contains important information on the product described in t

his documentation, its

handling and to a section of the documentation to which you should pay particular attention.

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens' products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be

connected to an enterprise network or the internet if and to the extent such a connection is

necessary and only when appropriate security measures (e.g. firewalls and/or network

segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit.

Siemens' products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers' exposure

to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under.

Preface

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

4Manual, 04/2018, A5E42681298B-AA

See also

IndustrialSecurity (http://www.siemens.com/industrialsecurity)

http://support.automation.siemens.com (http://support.automation.siemens.com)

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 5

Table of contents

Preface ................................................................................................................................................... 3

1 Documentation guide .............................................................................................................................. 7

2 Product overview .................................................................................................................................. 11

2.1 Properties................................................................................................................................11

3 Wiring ................................................................................................................................................... 17

3.1 Terminal assignment and power supply .................................................................................17

3.2 Connection examples .............................................................................................................25

4 Configuring/address space.................................................................................................................... 31

4.1 Configuring..............................................................................................................................31

4.2 Reaction to CPU STOP ..........................................................................................................32

4.3 Required I/O address space ...................................................................................................32

4.4 Parameter ...............................................................................................................................33

4.5 Control and feedback interface...............................................................................................35

4.5.1 Assignment of the control interface ........................................................................................35

4.5.2 Assignment of the feedback Interface ....................................................................................37

5 Programming ........................................................................................................................................ 41

5.1 General information ................................................................................................................41

5.2 "ECC4100" functions ..............................................................................................................41

5.3 FC ECC4100 parameters .......................................................................................................42

6 Interrupts/diagnostic messages............................................................................................................. 47

6.1 Status and error displays ........................................................................................................47

6.2 Interrupts.................................................................................................................................50

6.3 Diagnostics alarms..................................................................................................................50

6.4 Device defect ..........................................................................................................................52

7 Technical specifications ........................................................................................................................ 53

7.1 Technical specifications ..........................................................................................................53

Index..................................................................................................................................................... 57

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 7

Documentation guide

The documentation for the SIMATIC S7-1500 automation system and the SIMATIC

ET 200MP distributed I/O system is arranged into three areas.

This arrangement enables you to access the specific content you require.

Basic information

The System Manual and Getting Started describe in detail the configuration, installation,

wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7

online help supports you in the configuration and programming.

Device information

Product manuals contain a compact description of the module-specific information, such as

properties, wiring diagrams, characteristics and technical specifications.

General information

The function manuals contain detailed descriptions on general topics regarding the SIMATIC

S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web

server, OPC UA.

You can download the documentation free of charge from the Internet

(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-

overview/Pages/Default.aspx).

Changes and supplements to the manuals are documented in a Product Information.

Documentation guide

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

8Manual, 04/2018, A5E42681298B-AA

You can download the product information free of charge from the Internet

(https://support.industry.siemens.com/cs/us/en/view/68052815).

Manual Collection S7-1500/ET 200MP

The Manual Collection contains the complete documentation on the SIMATIC S7-1500

automation system and the ET 200MP distributed I/O system gathered together in one file.

You can find the Manual Collection on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86140384).

SIMATIC S7-1500 comparison list for programming languages

The comparison list contains an overview of which instructions and functions you can use for

which controller families.

You can find the comparison list on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86630375).

"mySupport"

With "mySupport", your personal workspace, you make the best out of your Industry Online

Support.

In "mySupport", you can save filters, favorites and tags, request CAx data and compile your

personal library in the Documentation area. In addition, your data is already filled out in

support requests and you can get an overview of your current requests at any time.

You must register once to use the full functionality of "mySupport".

You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).

"mySupport" - Documentation

In the Documentation area in "mySupport" you can combine entire manuals or only parts of

these to your own manual.

You can export the manual as PDF file or in a format that can be edited later.

You can find "mySupport" - Documentation on the Internet

(http://support.industry.siemens.com/My/ww/en/documentation).

"mySupport" - CAx data

In the CAx data area in "mySupport", you can access the current product data for your CAx

or CAe system.

You configure your own download package with a few clicks.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIWAREX MS Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Siemens

Siemens SINAMICS G130 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SENTRON PAC PROFIBUS DP Manual de usuario

Siemens

Siemens SIRIUS 3RA2712-.A Series Manual de usuario

Siemens

Siemens SIRIUS 3RF2330-DA Series Manual de usuario

Siemens

Siemens SIRIUS ACT 3SU1401-2EE20-6AA0 Manual de usuario

Siemens

Siemens LMV37.4 Series Manual del operador

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIRIUS 3RK3 Manual de usuario

Siemens

Siemens LMO14 Series Manual de usuario

Siemens

Siemens RMB795 Manual de usuario

Siemens

Siemens 6MB5110-1 Manual de usuario

Siemens

Siemens simovert masterdrives Manual de usuario

Siemens

Siemens SIRIUS 3RT1.5 Manual de usuario

Siemens

Siemens SIMATIC PCS 7 Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens SIMATIC NET PG-5412 Manual de usuario

Siemens

Siemens SIMOTION SCOUT Hoja de instrucciones

Siemens

Siemens MICROMASTER Vector 6SE32 Manual de usuario

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 Manual de usuario

Siemens

Siemens SIMATIC TI505 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario