Siemens SED2-LONI/F Manual de usuario

Installation Instructions

Document No. 129-387

October 2, 2009

SED2 VFD LON Interface Option

Item Number 129-387, Rev. BA Page 1 of 3

Product Description

The LONMARK® certified SED2 VFD LON Interface

Option (LON Interface) provides direct digital control of

SED2 Variable Frequency Drives (VFDs). The LON

Interface resides on a LONWORKS® network with

LONMARK products from multiple vendors.

Product Numbers

SED2-LONI/F, includes SED2 VFD LON Interface

Option, and CD-ROM with files and operating

instructions.

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not perform a

procedure as specified.

CAUTION:

Equipment damage, or loss of

data may occur if you do not

perform a procedure as specified.

Installation

SED2 VFD Frame Sizes A, B, and C

WARNING:

Make sure that the SED2 VFD is

de-energized (off) before you install or

remove the LON Interface Option.

1. Remove the SED2 VFD operator panel.

2. Install the LON Interface on the SED2 VFD I/O

module (Figure 1) by inserting two bottom guides

into appropriate slots at the sides of the I/O

module and pushing the upper section inward

until the locking mechanism latches.

3. Route the network cable (without connector) to

the LON Interface.

4. Terminate the end of network cable with a single,

two-pin, female LONWorks FTT-10A connector.

5. Attach the network cable FTT-10A connector to

connector at bottom of LON Interface (Figure 2).

6. Reinstall SED2 VFD operator panel on LON

Interface.

Figure 1. Installing LON Interface Option on SED2 VFD

Frame Sizes A, B, and C.

Figure 2. Network Connection on Bottom of

LON Interface Option.

SED2

VFD

INTERFACE

OPTION

Document No. 129-387

Installation Instructions

October 2, 2009

Page 2 of 3 Siemens Industry, Inc.

SED2 VFD Frame Sizes D, E, and F

WARNING:

Make sure that the SED2 VFD is

de-energized (off) before you install or

remove the LON Interface Option.

For frame sizes D, E, and F, the LON Interface mounts

inside the VFD housing.

1. Remove the SED2 VFD operator panel, side

cover, and bottom cover (Figures 3).

2. Disconnect operator panel extension module

(with ribbon cable) from control module by

pushing lever above extension module upwards

and simultaneously pulling extension module from

the upper sides and rocking it downward.

NOTE: Do not disconnect the ribbon cable.

3. Install the LON Interface on the control module

(Figure 4) by inserting two bottom guides into

appropriate slots at the sides of the control

module and pushing the upper section inward

until the locking mechanism latches.

4. Install the operator panel extension module on

LON Interface (Figure 4) by inserting two bottom

guides into appropriate slots at the sides of the

LON Interface and pushing the upper section

inward until the locking mechanism latches.

5. Route the network cable (without connector)

through a suitable cable opening to the LON

Interface (Figure 4).

6. Terminate the end of network cable with a single,

two-pin, female LONWorks FTT-10A connector.

7. Attach the network cable FTT-10A connector to

connector at bottom of LON Interface (Figure 2

and 4).

8. Reinstall the bottom cover, side cover, and the

SED2 VFD operator panel.

Figure 3. Removing the Operator Panel and Side Cover

of SED2 VFD Frame Sizes D, E, F.

Figure 4. Installing LON Interface Option on SED2 VFD Frame Sizes D, E, and F.

Document No. 129-387

Installation Instructions

October 2, 2009

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and

models as design improvements are introduced. Echelon, LonMark, LonWorks, LonTalk are registered trademarks of Echelon Corporation.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089

+ 1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com

Document No. 129-387

Printed in the USA

Page 3 of 3

Wiring

WARNING:

A VFD can be switched on unintentionally if

the serial bus installation is not operated

correctly. Only personnel who are qualified

and trained in installing systems of this type

should start the bus.

DIP Switch

Leave DIP switches OFF for proper operation of the

LON Interface.

WIRING

Wiring must conform to local codes and ordinances.

WIRE ROUTING

Maintain a minimum of 5 ft (1.5 m) between VFDs and

network or sensor wiring.

If it is necessary for network and sensor wring to cross

VFD wiring, it should cross at 90-degree angles.

POWER

The LON Interface receives power through its SED2

VFD connection. If VFD power is switched off, the

LON Interface will not communicate on the network.

LONTalk® NETWORK

The LONTalk network connection is on the bottom

edge of the LON Interface (Figure 2). Figure 5 shows

the wiring schematic for this connection. See

www.echelon.com for more details on the network

cable and the FTT-10A connector.

The installation is now complete.

NOTE: This connection supports twisted pair,

unshielded, polarity-insensitive, peer-to-peer

communications at 78 Kbps.

Figure 5. LON Interface Option Wiring Schematic.

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIMOCODE pro 3UF7902-0AA00-0 Manual de usuario

Siemens

Siemens VAG60 Series Manual de usuario

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Guía de inicio rápido

Siemens

Siemens Simatic S7-1500/ET 200MP Documento técnico

Siemens

Siemens SIPROTEC 7SJ61 Manual de instrucciones

Siemens

Siemens SINAMICS S120 Manual de lista de piezas

Siemens

Siemens REP-1 Manual de usuario

Siemens

Siemens SINORIX CPY-35 Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Manual del propietario

Siemens

Siemens EVG4U10E Series Manual de usuario

Siemens

Siemens SINUMERIK 880 SW 6 Manual técnico

Siemens

Siemens AP 118 Manual de servicio

Siemens

Siemens SIMATIC ET 200SP HA Guía del usuario

Siemens

Siemens SIRIUS K60 Series Manual de usuario

Siemens

Siemens SINAMICS G120 Guía de inicio rápido

Siemens

Siemens SIMADYN D FM 458 Manual de usuario

Siemens

Siemens WFZ56 Series Manual de instalación y operación

Siemens

Siemens SINAMICS G120P Instrucciones de montaje

Siemens

Siemens Cm-lon 6BK1700-0BA10-0AA00 Manual de usuario

Siemens

Siemens SIPROTEC 4 7XT7100-0 A00/EE Series Manual de usuario

Siemens

Siemens SINAMICS G120 Hoja de datos

Siemens

Siemens SIRIUS 3TK2834 Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario