Siemens FMT-A-ADPT Manual de usuario

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-050338-0

Class A Riser Module for the FMT

Installation Instructions

Model FMT-A-ADPT

INTRODUCTION The Model FMT-A-ADPT module (as shown in Figure 1) from Siemens

Industry, Inc., provides the FMT with Class A riser capability. The

telephone riser is supervised by the primary FMT.

PRE-INSTALLATION The FMT-A-ADPT is shipped with the bracket for use on the CC-2 or

CC-5 Card Cages attached to the FMT-A-ADPT board.

To use the FMTo use the FMT

o use the FMTo use the FMT

o use the FMT

-A-ADPT on a CC-2 Card Cage,-A-ADPT on a CC-2 Card Cage,

-A-ADPT on a CC-2 Card Cage, yy

you must place it inou must place it in

ou must place it inou must place it in

ou must place it in

Slot 1 (tSlot 1 (t

Slot 1 (terminals 9-1erminals 9-1

erminals 9-1erminals 9-1

erminals 9-16) of the top Double Header; on a CC-5 Card6) of the top Double Header; on a CC-5 Card

6) of the top Double Header; on a CC-5 Card6) of the top Double Header; on a CC-5 Card

6) of the top Double Header; on a CC-5 Card

Cage yCage y

Cage you must place it in Slot 5 (tou must place it in Slot 5 (t

ou must place it in Slot 5 (tou must place it in Slot 5 (t

ou must place it in Slot 5 (terminals 9-1erminals 9-1

erminals 9-1erminals 9-1

erminals 9-16) of the top Double Header6) of the top Double Header

6) of the top Double Header6) of the top Double Header

6) of the top Double Header..

The FMT-A-ADPT is shipped with two removable terminal plugs

(see Figures 5 and 6) that are installed in J1 and J2. Remove the

terminal plug from the CC-5/CC-2 header (terminals 9-16) where the FMT-A-ADPT will

be installed. Transfer the existing field wiring in the connector to connector J2 as

explained in the wiring section and discard the connector that was removed.

INSTALLATION

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

Install the FMT-A-ADPT (Refer to Figure 2) in the top header of the CC-5/CC-2. Insert

the female plug on the end of the FMT-A-ADPT into the appropriate top header (Slot 5

(FEMALE PLUG)

FMT-A-ADPT MODULE

PLUGS INTO TOP

DOUBLE HEADER OF

SLOT 5 OF CC-5 OR

SLOT 1 OF CC-2 CARD

CAGE.

CC-5 CARD CAGE

INSTALL FMT-A-ADPT

MODULE IN SLOT 5

OF CC-5 CARD

CAGE, AS SHOWN.

FOR CC-2 CARD CAGE,

INSTALL

MODULE IN SLOT 1

AND USE THIS SPACE

FOR CAPTIVE SCREW.

FMT-A-ADPT

CC-5 TOP DOUBLE

HEADER

CAPTIVE SCREW

ANY XLS SINGLE

SLOT MODULE

CC-5 BOTTOM

HEADER

SLOT FOR CAPTIVE

SCREW IN SLOT 1 OF

CC-2 TOP DOUBLE HEADER

SLOT FOR CAPTIVE

SCREW IN SLOT 5 OF

CC-5 TOP DOUBLE HEADER

Figure 3

FMT-A-ADPT Installed in CC-5

Figure 1

FMT-A-ADPT PCB

FMT-A-ADPT

16 9

12345678

Figure 2

FMT-A-ADPT

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-050338-0

for CC-5 or Slot 1 for CC-2) and then secure the retaining bracket under the XLS

module’s retaining captive screw that shares the space. Do not put the FMT-A-ADPT

under the bezel of the XLS module. (Refer to Figure 3.)

WIRING A 46-inch long 10-wire audio cable, P/N 555-150509, connects the FMT-A-ADPT to

the FMT to provide Class A riser capability. One end of this wire plugs into J4 of the

FMT-A-ADPT and the other end plugs into JP1 of the FMT. The connectors are keyed

and fit only one way. Make sure that all cables seat fully into their connectors.

Transfer any existing field wiring that was in positions 9-16 of the terminal block

header to the corresponding position on J2.

The screw terminals for J2 can accommodate one 12-22 AWG or two 16-24 AWG

(stranded only). For J1, the screw terminals can accommodate one 12-22 AWG or

two 16-18 AWG (stranded only). All wiring to the FMT-A-ADPT is power limited.

RETURN

FEED

NO CONNECTION

1234 5678

Figure 4

Wiring to J1

To Connect External Wiring 1. Insert the wire to be connected in the desired opening in the side of the remov-

able terminal block.

2. Tighten the appropriate locking screw.

3. Insert the removable terminal block in the appropriate header (J1 or J2) on the

FMT-A-ADPT.

LOCKING SCREWS

OPENING IN

SIDE FOR WIRE

CONNECTION

POSITION 8

POSITION 1

Figure 5

Plug for J1 (Positions 1-8)

ELECTRICAL RATINGS

LOCKING SCREWS

OPENING IN

SIDE FOR WIRE

CONNECTION

POSITION 16

POSITION 9

Figure 6

Plug for J2 (Positions 9-16)

tnerruCenalPkcaBV420

tnerruCV42lanimreTwercS

,snoitcurtsnInoitallatsnITMFehtotrefeR

nonoitamrofnirof,001430-513N/P

.TMFehtrofsgnitarlacirtcele

tnerruCenalPkcaBV2.60

tnerruCybdnatSV420

Otros manuales de Unidad de control de Siemens

Siemens

Siemens MXG461B Series Manual del propietario

Siemens

Siemens 2AI 2/4WIRE HF Manual de usuario

Siemens

Siemens HLIM Manual de servicio

Siemens

Siemens SINAMICS G120 Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Guía de inicio rápido

Siemens

Siemens SIRIUS 3RA2711-DB0 Series Manual de usuario

Siemens

Siemens K60R Manual de usuario

Siemens

Siemens IP-Module Manual de usuario

Siemens

Siemens AS-Interface 3RK2402-2 00 Series Manual de usuario

Siemens

Siemens SIMATIC S7-400H Manual de usuario

Siemens

Siemens SIMATIC ET 200SP HA Manual de usuario

Siemens

Siemens SIMATIC FM 450-1 Manual de usuario

Siemens

Siemens SIMATIC EMS400S PSB-S Manual de usuario

Siemens

Siemens SIMOTION D4 5-2 Series Manual de usuario

Siemens

Siemens SIMOCODE pro Manual de usuario

Siemens

Siemens SINAMICS G130 Manual de usuario

Siemens

Siemens Simatic S7-1500 CPU 1512C-1 PN Manual de usuario

Siemens

Siemens SIMATIC S5 Manual de usuario

Siemens

Siemens Cm-lon 6BK1700-0BA10-0AA00 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens PM330 Instrucciones de montaje

Siemens

Siemens S-60 Manual de usuario

Siemens

Siemens Logo! CM EIB Manual de usuario

Siemens

Siemens 545-714 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario