Siemens 8DO Manual de usuario

Installation Instructions

Document No. 129-565

April 28, 2015

EcoView™ 8 DO Module Installation and Commissioning

Item Number 129-565, Rev. CA Page 1 of 5

This document covers the installation and

commissioning of the EcoView™ 8 DO Module.

See the following documents for installation of other

EcoView system components:



EcoView Touchscreen Installation and System

Start-up

(129-562)



EcoView Thermostat Installation Instructions

(129-564 or 129-566)



EcoView Multi-phase Meter Installation

Instructions

(129-563)

Product Description

The EcoView 8 DO Module is an eight-channel, pilot-

duty controller module that is used to manage lighting

or other energy-consuming electrical loads that would

benefit from scheduling. Relay channels may be

accessed through the EcoView Touchscreen or

remotely through the EcoView Web application.

Product Number

57-002

EcoView I/O Module, 8 DO, with Zigbee,

includes power supply

Caution Notations

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools and Materials

Flat-blade screwdriver (1/8-inch blade width)

Wire strippers

Expected Installation Time

15 minutes for installing the EcoView 8 DO Module

30 minutes for wiring each DO

Prerequisites

NOTE: If the EcoView 8 DO Module will be directly

controlling line voltage, it must be mounted in

an appropriate plastic NEMA enclosure.

The EcoView Touchscreen is installed and started up

according to the

Installation Instructions

(129-562).

A 120 Vac outlet is available for the EcoView 8

DO Module power supply.

Depending on the type of installation, other

prerequisites may have to be completed.

Installation

CAUTION:

Always wear an electro-static discharge

(ESD) wrist strap and discharge

accumulated static before touching field

panel components.

Install the EcoView 8 DO Module near the loads

to be controlled.

1. If the EcoView 8 DO Module will be directly

controlling line voltage, mount the plastic NEMA

enclosure in the desired location.

2. If necessary, install a standard 120 Vac outlet in

the enclosure where the EcoView 8 DO Module

power supply will be attached.

3. Using the provided screws, mount the EcoView 8

DO Module assembly in the enclosure.

4. Attach the EcoView 8 DO Module 24 Vac power

supply to the standard 120 Vac outlet and secure

with the provided plate screw.

5. Wire the individual circuits to be controlled to the

2-pin connectors for Relay 1 – Relay 8.

NOTE: The relays are capable of controlling loads up

to 240 Vac at 3A. Anything outside of this

range should be controlled by contactors.

Document No. 129-565

Installation Instructions

April 28, 2015

Page 2 of 5 Siemens Industry, Inc.

Figure 1: EcoView™ 8 DO Module Reset Button Location.

Commissioning the 8 DO Module

In order to commission the EcoView 8 DO Module to

the ZigBee network, the DO module needs to be reset.

1. Press the recessed Reset button four times in

rapid succession (see Figure 1).

 The NET light stops flashing.

The NET light starts flashing again once it has

joined the ZigBee network.

2. Press the Reset button once to send the Node ID

information to the EcoView Touchscreen.

Assigning the 8 DO Module to the

Touchscreen

1. Press the EcoView Touchscreen CONFIG button

for one second and then release it to display the

Configuration screen (see Figure 6).

2. Press the DEVICE SETTINGS icon.

3. Press the Configure tab.

 The EcoView 8 DO Module’s MAC address displays

in the Unassigned Nodes list. (See Figure 6.)

 Assigned and unassigned EcoView 8 DO

Modules, EcoView Multi-phase Meters, and

EcoView Thermostats display in the

Configured Device list.

NOTE: Join devices one-at-a-time. This minimizes any

confusion caused by having several MAC

addresses displayed on the screen at one time.

4. Select a device from the Unassigned Nodes list

to start the Device Configuration Wizard.

Figure 2: Device Settings/Configure Tab.

5. Select the Resource Controller device driver

from the list, and then press the Next button.

Figure 3: Device Wizard Driver Selection.

6. If needed, select the Relay Delay parameter to

edit the value, and then press the Next button.

Figure 4: Device Wizard Parameters.

Siemens Industry, Inc.

Page 3 of 5

7. Select the appropriate Zigbee MAC Address for

the 8 DO Module from the list, and then press the

Finish button.

Figure 5: Device Wizard Zigbee MAC Selection.

8. Press the Accept button.

⇨The EcoView 8 DO Module is assigned to the

EcoView Touchscreen and locked into the

wireless network.

9. In the upper-left corner of the screen, press the

Home button to return to the main screen.

10. Press the Exit button to save the configuration.

The installation and commissioning are now complete.

Figure 6: Advanced Device Configuration Screen.

Troubleshooting

➤If the EcoView 8 DO Module’s MAC address is

not displayed on the Device Network screen,

repeat the steps in the

Commissioning the 8 DO

Module

section.

Removing Device(s) Installed to an EcoView

Touchscreen in Error (Only for Sites with

Multiple Touchscreens)

Use this procedure if the EcoView 8 DO Module has

joined the wrong EcoView Touchscreen network.

1. Remove the front bezel of the EcoView Touchscreen

that the 8 DO Mdoule has joined in error.

2. Press and hold the EcoView Touchscreen

CONFIG button for one second to display the

Configuration screen.

3. Press the DEVICE SETTINGS icon.

4. Press the Advanced tab.

5. On the right side of the screen, press the Open

button to toggle the network to closed.

The button text changes to Closed.

Document No. 129-565

Installation Instructions

April 28, 2015

Page 4 of 5 Siemens Industry, Inc.

6. Press the Configure tab and deselect Hide

Configured Devices.

7. In the list, select the EcoView 8 DO Module.

8. In the Device Configuration Wizard, press the

Decommission button.

9. Press the Accept button.

10. Return to the EcoView 8 DO Module and install it on

the correct EcoView Touchscreen network.

Resetting the EcoView 8 DO Module to

Manufacturer’s Defaults

Use this procedure to reset the EcoView 8 DO

Module to the manufacturer’s defaults.

➤Press and hold the recessed RESET button for

more than 10 seconds and then release it.

 The LEDs on the EcoView 8 DO Module should

cycle off, then turn on again.

FCC and IC Interference

Requirements

“This device complies with Part 15 of the FCC Rules

and with Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two

conditions (1) this device may not cause harmful

interference, and (2) this device must accept any

interference, including interference that may cause

undesired operation of the device.”

« Ce dispositif est conforme à la partie 15 des règles

de FCC et aux normes permis-exemptes du Canada

RSS d'industrie. L'opération est sujette aux deux

conditions suivantes (1) que ce dispositif peut ne pas

causer l'interférence nocive, et (2) ce dispositif doit

accepter n'importe quelle interférence, y compris

l'interférence qui peut causer le fonctionnement peu

désiré du dispositif. »

Per RSS-Gen Issue 3 (December 2010 Section 7.1.3)

FCC Note

This device complies with Part 15 of the FCC rules.

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC and IC Radiation Exposure

Statement for Mobile Devices

“This equipment complies with FCC and IC radiation

exposure limits set forth for an uncontrolled

environment. This equipment shall be installed and

operated with minimum distance 20cm between the

radiator and your body. This transmitter must not be

re-located or operating in conjunction with any other

antenna or transmitter.”

(For compliance with FCC Code of Federal

Regulations Title 47 Part 2.1093)

Document No. 129-565

Installation Instructions

April 28, 2015

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and

models as design improvements are introduced. EcoView is a trademark of Siemens Industry, Inc. Other product or company names

Siemens Industry, Inc.

Building Technologies Division

Retail and Commercial Systems

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

USA

+1 847-215-1000

For EcoView system support, please call

1 + 877-306-9400

Your feedback is important to us. If you have

comments about this document, please send

them to SBT_technical.edi[email protected]

Document No. 129-565

Printed in the USA

Page 5 of 5

FCC Code of Federal

Regulations Title 47 Part

15.105

Information to the user:

This equipment has been tested and found to

comply with the limits for a Class B, digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turnings

the equipment off and on, the user is encouraged

to try to correct the interference by one or more of

the following measures:

Reorient or relocate receiving antenna.

Increase the separation between the

equipment and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV

technician for help.

For Industry Canada User

“This Class B digital apparatus complies with

Canadian ICES-003 Issue 4 (February 2004).”

« Cet appareillage numérique de la classe B est

conforme ICES-003 à l'issue canadienne 4 (le

février 2004). »

Antenna

“Under Industry Canada regulations, this radio

transmitter may only operate using an antenna of

a type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce

potential radio interference to other users, the

antenna type and its gain should be so chosen

that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for

successful communication.”

« Aux termes des règlements du Canada

d'industrie, cet émetteur radioélectrique peut

seulement fonctionner utilisant une antenne d'un

type et (ou moins) d'un gain maximum approuvés

pour l'émetteur par Industry Canada. Pour

ramener des interférences radio potentielles à

d'autres utilisateurs, on devrait ainsi choisir le

type d'antenne et son gain que l'équivalent a

isotropically rayonné la puissance (e.i.r.p.) n'est

pas plus que celui nécessaire pour la

communication réussie. »

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens Climatix POL822 Manual de usuario

Siemens

Siemens SIMOTION SCOUT Hoja de instrucciones

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens SITRANS F Manual de usuario

Siemens

Siemens 3VL93 Series Manual de usuario

Siemens

Siemens SIMATIC EP200SP Manual de usuario

Siemens

Siemens VVI46 Series Manual de usuario

Siemens

Siemens HiPath optiPoint 410 Manual de instrucciones

Siemens

Siemens SICAM A8000 Series Manual de usuario

Siemens

Siemens SIRIUS 3RW44 Manual de usuario

Siemens

Siemens SIMOTION D4 5-2 Series Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC IM151-1 STANDARD Manual de usuario

Siemens

Siemens SIMATIC ET 200eco PN Documento técnico

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIRIUS ACT 3SU1400-1GC10-1AA0 Manual de usuario

Siemens

Siemens MICROMASTER 411 Manual de usuario

Siemens

Siemens SIRIUS ACT 3SU1400-2EM10-6AA0 Manual de usuario

Siemens

Siemens 6ES7134-4FB51-0AB0 Manual de usuario

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A Manual de usuario

Siemens

Siemens LFE1 Series Manual de usuario

Siemens

Siemens PXA30 Series Manual de usuario

Siemens

Siemens SIMATIC Manual de usuario

Siemens

Siemens SIMATIC TI505 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario