SEWOO LK-P11W Manual de usuario

All specifications are subject to change without notice

MOBILE PRINTER

MODEL : LK-P11W

Rev. 2.0

SEWOO TECH CO.,LTD.

Doosung BD, 689-20, Geumjeong-dong, Gunpo-si, Gyeonggi-do, 435-862, Korea

TEL : +82-31-459-8200 FAX : +82-31-459-8880

www.miniprinter.com

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION

Table of Contents

Unpacking

2. Product overview 3

3. Installation & Usage 4

3-1. Control Panel Usage 4

3-2. Battery Installation 5

3-3. Battery removel 6

3-4. Battery Charging 7

3-5. Battery Charger Usage 8

3-6. Usage of Cigar Jack for charging 9

3-7. Belt clip usage 10

3-8. Roll Paper Installation 11

3-9. Leather case Usage 12

3-10. Shoulder Strap Usage 13

3-11. Self Test 14

4. Peripherals Connection 17

4-1. Wiﬁ(802.11b/g) Connection 17

4-2. Interface Cable Connection 18

5. Printer Cleaning 19

6. Product Speciﬁcation 20

6-1. Speciﬁcation 20

7. CPCL Command Compatibilit

1. Unpacking

Printer case

Cigar jack

Battery Holder

(Cradle)

shoulder strap

Quick Manual

Printer Battery

Roll paper

Belt Buckle

USB Shelded Cable

Recharger Serial Cable

Optional

Standard

2. Product overview

Power switch

Charger

Connector

Cover open

button

Battery

Paper feed

button

SERIAL

USB

Front

Side

3-2. Installing battery

Insert the battery inside printer as

shown.

As the battery is not charged at the time of your purchase, charge the battery

prior to using the product.

(Use the battery charger and/or the optional battery holder.)

Push the Open to the direction as

pointed by arrow in the image.

1 2

Open the battery cover and push up

the hook to the direction as above.

Close the battery cover once you

inserted the battery completely.

NOTE

3-1. Control Panel Usage

Button Name function

Power

button

This button is used to turn the printer on and off.

When the printer is off,press this button for approximately

2 seconds and it will turn on the power.When you press this button

in a state that the printer is on, the printer will turn off.

Paper

Feed

Button

Paper output can be done manually by pressing this button.

Additionally, self-testing and Hexadecimal Dumping can be processed..

1.Refer to“3-10” for self test information.

2. Refer to the service manual regarding Hexadecimal Dumping.

Battery

Status

Lamp

1.If the Batt,LED are Lit, the battery is fully charged.

2. If you can hear beeping sound and LED light is turned off, it means

that the battery is at the lowest level.

3. If the battery is not charged at all, the printer turns off automatically.

Error

Lamp If the red light is turned on, it means that the paper cover is open.

3. Setting Up the Product

3-4. Battery Charging

1. The battery can be charged only when the temperature is 0~40℃

2. Be sure that the printer is turn off and the battery to be charged is installed.

3. Connect the charger to the printer.

4. Recharging will now be started.

NOTE

1. Unless the exclusive charger is used provided by the manufacturer, the printer

can be damaged, and the manufacturer is not liable for the consequential damage.

2. Before removing the battery, make sure that power is turned off.

3. Printer does not work in the status of being connected with charger only.

4. The battery should be installed to operate printer.

5. While charging, do not turn on the power.

6. Do not operate the print while charging the battery.

7. Do not connect the charger while the printer is operated.

3-3. Battery removel

Push the Open into the direction

indicated with the arrow in the image.

Pull out the battery as shown above.

1 2

Push up the hook after opening the

battery cover.

3-4-1 The status of lamp in charging

Status charging charging complete

Charging Lamp Red

Green

②

①

LED

Connect the car cigar JACK charger into the printer or battery holder.

3-6 Usage of Cigar Jack Charger for charging

Printer

Battery holder

NOTE

Use the Cigar Jack offered by the manufacturer

Optional

Input 12 ~ 24V

8.4V 0.8 ~ 1.2A

Output

3-5. Battery charger Usage

1. Please press the battery into the holder until you can hear a snapping sound.

2. Insert DC JACK ① into the end completely as the direct shown above.

3. Plug the power code to electrical outlet.

4. While charging the battery, red light turns on.

Once the charge is completed, green light turns on.

Check the state of code connection when error occurs blinking on red light.

3-5-1 The status of lamp in charging

Status charging charging complete

Charging Lamp Red

Green

NOTE

In the case the battery is not ﬁxed properly in the holder, the red lamp will be blinking,

Then, extract and reinsert the battery.

Optional

②

①

LED

3-8. Roll Paper Installation

1 2

Open the paper cover pressing the open

button. Insert a sharp tool into the paper

guide hole and push it in the direction of

arrow as shown above.

Put the paper in the right direction after

adjusting the paper guide matching the paper

width. (Remove the paper core when it is

used all)

Pull out a short length of the paper and

shut the paper cover.

Press the Feed Key once to arrange

the paper.

3-7. Belt clip Usage

Insert the belt hook screw into the hole of the belt hook.

As shown above,fasten the screw with a screw driver.

3-10. Shoulder Strap Usage

1 2

Insert the strap into the hook on

the printer.

Place the end of strap into the hook of

shoulder strap.

After pulling out the end of strap

tightly, put it into the clip to be

fastened.

Fasten the strap in the opposite

side with the sample way.

Optional

3-9. Leather Case Usage

1 2

Open the Velcro Put the printer into the leather case

following the direction shown in the

image.

Close the Velcro

Optional

The sample of self test printout

3-11. Self Test

1 2

NOTE

Turn off the power pressing the

power button for approximately

3 seconds.

The printout is produced.

While you are pressing the FEED

button, press the power button

1. To print ASCII pattern additionally,

press the Feed button once more

2. After printing ASCII pattern, the

self test will be ﬁnished automatically.

3. If the Feed button is not pressed

to print ASCII pattern, self test will be

ﬁnished automatically after 30 seconds.

4. Peripherals Connection

When the printer is installed initially or when you face a problem, you can run the

self test and check the information about

-Control Circuit, Mechanism, Print Quality, ROM Version

After checking with self-test and no issues are found, you can examine other

devices and software. This function is working independent of devices and software.

●

Motor protection from being overheated

The motor should be stopped and cooled about more than 30 seconds after

continuous printing 1.5 meter

This product can communicate with other devices via Wiﬁ(802.11b/g)

communication and cable.

1. The Printer can be connected to devices equipped with wiﬁ(802.11b/g)

communication capacity (PDAs, PCs, etc.)

2. Use the wiﬁ(802.11b/g) connection function supported by the device to

connect to the printer.

4-1 Wi(802.11b/g) Connection

NOTE

Refer to the wiﬁ(802.11b/g) Manual for more details on connection.

Tabla de contenidos

Otros manuales de Impresora de SEWOO

SEWOO

SEWOO SLK-T213EB Series Manual de usuario

SEWOO

SEWOO SLK-T32EB II Manual de usuario

SEWOO

SEWOO SLK-TL100 Manual de usuario

SEWOO

SEWOO SLK-T21EB Series Manual de usuario

SEWOO

SEWOO LK-P12 Manual de usuario

SEWOO

SEWOO LK-P SERIES Hoja de instrucciones

SEWOO

SEWOO SLK-TS400EB Manual de usuario

SEWOO

SEWOO SLK-TL21 Series Manual de usuario

SEWOO

SEWOO LK-P30 Instrucciones de instalación

SEWOO

SEWOO SLK-TL21 Series Manual de usuario

SEWOO

SEWOO LK-B10 Manual de usuario

SEWOO

SEWOO SLK-TE25 Manual de usuario

SEWOO

SEWOO LK-P43W Manual de usuario

SEWOO

SEWOO LK-P11B Manual de usuario

SEWOO

SEWOO WTP-100 Manual de usuario

SEWOO

SEWOO LK-P34 Manual de usuario

SEWOO

SEWOO LK-P41B Manual de usuario

SEWOO

SEWOO LK-P30 Manual de usuario

SEWOO

SEWOO SLK-TS400 Manual de usuario

SEWOO

SEWOO LK-P30B Manual de usuario

SEWOO

SEWOO SLK-TE21 Series Manual de usuario

SEWOO

SEWOO LK-P12W Manual de usuario

SEWOO

SEWOO SLK-TE21X Series Manual de usuario

SEWOO

SEWOO SLK-TL20 Series Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario