SEWOO LK-P41 Guía de instalación

P41 Rev. H 09/18

J. STEPHEN Co., Ltd.

28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do, 18103, Republic of Korea

TEL : +82-31-8077-5000 FAX : +82-31-459-8880

www.miniprinter.com

All specifications are subject to change without notice

MOBILE PRINTER

MODEL : LK-P41

Table of Contents

Safety Precautions

Unpacking

Product Overview

Usage and Installation

4-1. Control Panel Usage 6

4-2. Battery Installation 7

4-3. Charging Battery 8

4-4. Charging Cradle

(Optional)

4-5. Car Charger Usage

(Optional)

4-6. Paper Installation 11

4-7. Leather Case Usage

(Optional)

4-8. Self Test 13

4-9. Cleaning the Printer 15

5. Peripheral Connection 16

5-1. Bluetooth Connection

(Optional)

5-2. Wi-Fi Connection

(Optional)

5-3. Interface Cable connection 17

Printer Specication

CPCL Command Compatibility

Setting up the Software

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference received,

including interference that may cause undesired operation.

Vic Barczyk

20280 S. Vermont Ave. STE 200, Torrance, CA 90502 | USA

+310-561-8030

For better safety and reliability, adhere to the following precautionary measures.

Read and follow the instructions carefully before operation of the product.

1. Safety Precautions

WARNING

Failure to follow these instructions could result in re, electric shock, other

injuries, or property damage.

Indication

Prohibition

(Potential risk of electric shock or re)

Must follow

Do not disassemble Unplug the power from the

outlet

Grounding to prevent electric

shock

Do not handle the product

with wet hands

Do not pull or touch the power plug with

wet hands.

Do not bend the wire and do not allow the

wire to be pinched or crushed by heavy

objects.

If a power plug is broken or a plug is cut or

worn, do not use it.

Do not overload an electrical outlet.

WARNING

Failure to follow these instructions could result in re, electric shock, other

injuries, or property damage.

Failure to follow these instructions could result in re, electric shock,

other injuries, or property damage.

(Turn off the power using the power button)

(May cause damage or injury)

(Potential risk of re or unit malfunction)

(Potential risk of re or property damage)

(Potential risk of electric shock or damage)

(Potential risk of malfunction, electric shock,

or re. When the product needs to be repaired,

please contact your reseller)

Dealer

Do not unplug the power cable to turn off

the product.

Do not install the product on an unstable

or inclined surface.

If the product needs to be repaired,

please contact your reseller.

Avoid excessive shock or drops.

Keep product away from the water and

other material.

Do not disassemble, repair or modify the

product.

CAUTION

2. Unpacking

Printer Battery

Serial Cable

Roll Paper

USB Cable

Charger

CD Quick Manual

Battery Cradle

(Charging Cradle) Leather Case Shoulder Strip

CarAdapter

Optional

Standard

3. Product Overview

Paper Feed

Button

Power

Switch

DC Power

Battery

SERIAL

USB

Open Button

Front

Rear

Button

Name

function

Power

button

This button is used to turn the printer on and off.

When the printer is off,press this button for approximately 3 seconds

and the printer will power on.When you press this button while the

printer is powered on, the printer will turn off.

Paper

Feed

Button

This button can be used to manually feed the paper.

Additionally, this button is also used to initiate self-tests and

Hexadecimal Dumping.

1. Refer to the Self Test section of this manual for information

regarding self-tests.

2. Refer to the Note in Self Test section of this manual for information

regarding Hexadecimal Dumping.

Battery

Status

Lamp

1. If the Batt LED is lit, the battery is fully charged.

2. If you can hear a beeping sound and LED light is turned off,

the battery is at the lowest level.

3. If the battery is not charged at all, the printer turns off

automatically.

Error

Lamp If the red light is turned on, there is no paper or

the paper cover is open.

4. Usage and Installation

4-1 Control Panel Usage

1. Align battery hook as shown in the picture

2. Push the battery into the printer until it locks in place.

NOTE

As the battery is not charged at the time of your purchase, charge the

battery prior to using the printer

(Battery charger or Cradle can be used to charge)

CAUTION

Risk of explosion if the battery is replaced by an incorrect type.

Dispose of used batteries according to local regulations.

Hook

4-2 Battery Installation

The charging status LED

Status Charging Charging complete

Charging Lamp Red

Green

NOTE

1. If the charger provided by the manufacturer is not used, the printer can be damaged,

and the manufacturer is not liable for the consequential damage.

2. Before removing the battery, make sure that power is turned off.

3. The printer does not work when only connected to the charger.

4. The battery needs to be installed to operate the printer.

5. While charging, do not turn on the power.

6. Do not operate the printer while charging the battery.

7. Do not connect the charger while the printer is operating.

1. Make sure the printer is turned off.

2. After opening the DC JACK cover, connect the DC JACK to the printer.

3. Plug the power cord into the electrical outlet.

4-3 Battery Charging

Lamp

The charging status LED

Status Charging Charging complete

Charging Lamp Red

Green

NOTE

If the printer is not properly mounted on the charging cradle, the red lamp will blink.

Remove and reinsert the battery.

4-4 Charging Cradle

DC Jack

1. Place the printer into the charging cradle as shown above.

2. Connect the DC JACK to the charging cradle.

3. Plug the power cord into an electrical outlet.

4. Once the charging is completed, remove the printer from the charging cradle.

Optional

Lamp

10 11

Connect the car charger to the printer or battery cradle.

4-5 Car Charger Usage

Printer

Battery holder

Optional

NOTE

Only use cables included with the printer.

Input 12 ~ 24V

8.4V 0.8 ~ 1.2A

Output

1 2

Press the PUSH button to open

the paper cover

Pull a short length of paper out of the

printer and close the cover.

Insert the paper in the correct

direction. See the image above.

Tear off the additional paper using

tear bar.

4-6 Paper Installation

12 13

1 2

Open the leather case

Close the cover and press down on

the Velcro.

Place the printer into the leather case

4-7 Leather Case Usage

Optional

1 2

NOTE

Turn off the power by pressing the

power button for approximately

3 seconds.

The self-test will print.

While you are holding the FEED button,

press the power button.

4-8 Self Test

1. To print ASCII pattern additionally,

press the Feed button once more

2. After printing ASCII pattern, the

self test will be nished automatically.

3. If the Feed button is not pressed

to print ASCII pattern, self test will be

nished automatically after 3 seconds.

14 15

Upon initial installation or for troubleshooting, you can run the diagnostic test

to get information about:

Firmware version, emulation, codepage, sensor settings, interface settings, etc.

If no issues are found with the diagnostic test, examine other devices and software.

The diagnostic test is working independently of devices and software.

●

Motor protection from being overheated

To prevent the motor from overheating, stop the printer for at least 30 seconds

after continuously printing 1.5 meters.

Self-Test Printout Sample

If the interior of the printer is dusty, printing quality can lowered.

In such a case, follow the instructions below to clean up the printer.

NOTE

1. Make sure to turn the printer power off prior to cleaning.

2. Regarding printhead cleaning, as the printhead gets very hot during printing,

turn off the printer power and wait approximately 10 minutes before cleaning.

3. When cleaning the printhead, take care not to touch the heated portion of

the printhead. The printhead can be damaged by static electricity.

4. Take care not to allow the printhead to become scratched and /or damaged in any way.

1. Use an applicator swab moistened with an alcohol solution to clean the printhead

and remove any dust.

2. Once the cleaning is completed, wait a few minutes before inserting the paper roll into

the printer.

Preventing Overheating

To prevent the motor from overheating, continuous driving of the printer

should be 1.5 m or less in print length. Set the pause time for 30 seconds

or more after driving the printer.

4-9 Cleaning the Printer

16 17

5. Peripheral Connection

This product can communicate with other devices via Bluetooth, Wi-Fi, or

a communication cable.

5-3 Interface Cable Connection

1. Connect USB cable to the connector on the printer.

2. Connect the interface cable to the USB port of the device (PDA, PC, etc.).

NOTE

Only use cables included with the printer.

Serial

USB

1. The Printer can be connected to devices equipped with Bluetooth communication

capabilities (PDAs, PCs, etc.).

2. Use the Bluetooth connection function supported by the device to connect

to the printer.

5-1 Bluetooth Connection

NOTE

Please refer to the conguration manual for details.

NOTE

Please refer to the conguration manual for details.

5-2 Wi-Fi Connection

1. The Printer can be connected to devices equipped with Wi-Fi communication

capabilities (PDAs, PCs, etc.).

2. Use the Wi-Fi connection function supported by the device to connect to

the printer.

Optional

Otros manuales para LK-P41

Tabla de contenidos

Otros manuales de Impresora de SEWOO

SEWOO

SEWOO LK-P22 Manual de usuario

SEWOO

SEWOO LK-P31 Manual de usuario

SEWOO

SEWOO LK-P41 Instrucciones de instalación

SEWOO

SEWOO LK-P34 Manual de usuario

SEWOO

SEWOO LK-P25 Manual de usuario

SEWOO

SEWOO LK-P43 Manual de usuario

SEWOO

SEWOO SLK-TE21 Series Manual de usuario

SEWOO

SEWOO SLK-TE32 Series Manual de usuario

SEWOO

SEWOO SLK-TL100II Manual de usuario

SEWOO

SEWOO LK-P43 Manual de usuario

SEWOO

SEWOO LK-P20II Manual de usuario

SEWOO

SEWOO LK-P30B Manual de usuario

SEWOO

SEWOO LK-PXX Manual de usuario

SEWOO

SEWOO SLK-T213EB Series Manual de usuario

SEWOO

SEWOO SLK-T32EB Series Manual de usuario

SEWOO

SEWOO LK-P32 Manual de usuario

SEWOO

SEWOO LK-P30W Manual de usuario

SEWOO

SEWOO SLK-T12EB Manual de usuario

SEWOO

SEWOO SLK-TE12 Series Manual de usuario

SEWOO

SEWOO SLK-T21EB Series Manual de usuario

SEWOO

SEWOO LK-P400 Manual de usuario

SEWOO

SEWOO LK-P43B Manual de usuario

SEWOO

SEWOO LK-P22 Manual de usuario

SEWOO

SEWOO SLK-TL100 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario