SEWOO LK-P20II Manual de usuario
2-inch Label
Mobile Printer
Mobile PrinterMobile Printer
Mobile Printer
Technical Manual
Technical ManualTechnical Manual
Technical Manual
SEWOO TECH
SEWOO TECHSEWOO TECH
SEWOO TECH CO., LTD
CO., LTD CO., LTD
CO., LTD
www.miniprinter.com
www.miniprinter.comwww.miniprinter.com
www.miniprinter.com
Rev 1.0
2008.07.24
2
2-inch Label Technical Manual
TABLE OF CONTENTS
1. Programming Introduction 5
2. Printer Commands 6
A. Printer Commands
B. PRINT Command
C. FORM Command
D. JOURNAL Command
E. UNITS Command
F. Using Commend
6
7
7
7
8
9
3. TEXT 10
A. TEXT Command
B. FONT-GROUP(FG) Command
C. TEXT CONCATENATION Command
D. MULTILINE(ML) Command
E. COUNT Command
F. SETMAG Command
10
11
12
13
14
14
4. Linear Bar Codes 15
A. BARCODE Command
B. BARCODE-TEXT Command
15
16
5. Two-Dimensional Bar Codes 17
A. PDF417 (PORTABLE DATA FILE)
B. MAXICODE
17
18
6. Graphics 20
A. BOX Command
B. LINE Commands
C. INVERSE-LINE Commands
D. PATTERN Command
E. GRAPHICS Commands
F. PCX Commands
20
20
21
21
22
23
3
2-inch Label Technical Manual
7. Advanced Commands 24
A. CONTRAST Command
B. TONE Command
C. JUSTIFICATION Commands
D. PAGE-WIDTH Command
E. PACE Command
F. NO-PACE Command
G. WAIT Command
H. SPEED Command
I. SETSP Command
J. ON-OUT-OF-PAPER Command
K. ON-FEED Command
L. PREFEED Command
M. POSTFEED Command
N. COUNTRY/CODE PAGE Command
O. USING FORMAT FILES
P. BEEP Command
24
24
24
25
26
26
26
27
27
27
28
28
29
29
30
30
8. Line Print Mode 31
A. SETLP Command
B. SETLF Command
C. Moving With X and Y Coordinates
D. LMARGIN Command
E. SETBOLD Command
F. SETSP Command
G. PAGE-WIDTH Command
H. PAGE-HEIGHT Command
I. Special ASCII Characters
J. SETFF Command
K. SET-TOF Command
L. SETLP-TIMEOUT
31
31
31
32
32
32
33
33
33
33
34
34
4
2-inch Label Technical Manual
9. Advanced Utilities 35
A. VERSION Utility
B. CHECKSUM Utility
C. DEL Utility
D. DIR Utility
E. DEFINE-FILE(DF) Utility
F. TYPE Utility
G. BAUD Utility
H. TIMEOUT Utility
I. ON-LOW-BATTERY Command
J. LT Command
K. SET-TIME Utility
L. GET-TIME Utility
M. SET-DATE Utility
N. GET-DATE Utility
O. Printing a Time Stamp
P. Printing a Date Stamp
Q. PAPER-JAM Utility
35
35
35
35
36
36
36
37
37
37
38
38
38
39
39
39
40
10. Printer Escape Commands 41
A. SET AND READ CODE Command
B. STATUS/INFORMATION
C. POWER OFF Command
41
41
42
11. Configuration/Control Commands 43
A. Command Format
B. Commands/Parameters
43
43
5
2-inch Label Technical Manual
1. Programming introduction
This manual details the various commands in the CPCL language which allow the programmer to utilize
the built in text, graphics, bar code printing and communications capabilities. The following notation
conventions are used throughout this manual.
{
Required item
[]
Optional item
()
Abbreviated command
<>
Literal item
A space character is used to delimit each field in a command line.
Getting Printer Information
The printer can print a report containing information about the application resident in the printer memory.
This information can be printed by following these procedures.
1. Turn off the printer
2. While holding the FEED key down, turn the printer on.
3. When printing begins, release the FEED key.
The printing will contain information about printer model, ROM version, serial number, baud rate, USB, Bluetooth,
font extra information which has been saved in the printer. In addition, certain amount of ASII hex codes will be
printed to check the printing quality.
If you require to set for communication Diagnostic Mode, press FEED button again after printing information by
following the steps above. The printer then indicates received information with hexadecimal.
Label aker
As LaberMaker has similar interface as general graphic edit tool, you can design readily without specific expertise
for programming and print the data through LUKHAN Portable Printer. Moreover, you are able to save the label
image into your PC with LBL file format. Saved label file can be reopening and edited.
Apart from the function of designing, you can save the file by communicating with printer, reopen saved file or see
the state information of the printer.
6
2-inch Label Technical Manual
2. Printer commands
A label file always begins with the “!” character followed by an “x” offset parameter, “x” and “y” axis
resolutions, a label length and finally a quantity of labels to print. The line containing these parameters is
referred to as the Command Start Line.
A label file always begins with the Command Start Line and ends with the “PRINT” command. The
commands that build specific labels are placed between these two commands.
☞
☞☞
☞ NOTE:
NOTE: NOTE:
NOTE:
Every line in the command session must be terminated with both carriage-return and line –feed
characters. All printer Commands must be in uppercase character ONLY.
A. PRINTER Commands
Form
<!> {offset <200> <200> {height {qty
<!>
Session start
{offset
The value of label horizontal offset
<200>
Horizontal resolution
<200>
Vertical resolution
{height
Maximum value of Label Height
The Maximum height of the label is the numerical value deducted 1/16” (1.5mm) from the value which
is measured from first bar (or gap) to the next bar (or gab). (In dots: 12donts on 203 dpi).
The quantity of label. The maximum value is 1024
7
2-inch Label Technical Manual
B. Print command
The print command terminates and prints the file. This must always be the last command (except
when in Line Pint Mode). Upon execution of the Print command, the printer will exit from a control
session. Be sure to terminate this and all commands with both carriage-return and line-feed characters.
Format
Format
{command
Command & option
{command
PRINT
C. FOR Command
The Form command will execute a form feed after the label is printed and instructs the printer to feed
to top of form after printing.
Format
{command
Command & option
{command
FORM
D. JOURNAL Command
Be default, the printer will check for correct media alignment if it encounters the eye-sense mark
during a print cycle. If necessary, the Journal command can be used to disable this automatic
correction feature.
Format
{command
Command & option
{command
JOURNAL
8
2-inch Label Technical Manual
E. UNITS Command
The Units commands are used to specify a measurement system for all subsequent command fields
in a control session. Coordinates, widths, and heights for all control commands can be entered with
precision for four decimal places. The printer measurement system will default to dots until a units
command is issued.
Format
{command
Command & option
IN-INCHES Measurement in inches.
IN-CENTIMETERS Measurement in centimeters
IN-MILLIMETER Measurement in millimeters.
{command
IN-DOTS Measurement in dots
9
2-inch Label Technical Manual
F. Using Comments
Comments can be added between the first line of a command start line and the print command.
A comment is placed in the file by starting a line with the ‘;’ character in the first column. Any
remaining text to the end of the line will be ignored. Comments are illegal between the CONCAT and
ENDCONCAT commands.
10
2-inch Label Technical Manual
3. TEXT
A. TEXT Commands
The TEXT command is used to place text on a label. This command and its variants control the
specific font number and size used, the location of the text on the label.
Format
{command {font {size {x {y {data
Command & option
TEXT (or T) Prints text horizontally
VTEXT (or VT) Prints text (vertically) rotated 90degrees counterclockwise
TEXT90 (or T90) Same as VTEXT above.
TEXT180 (or T180)
Prints text (upside down) rotated 180 degrees
counterclockwise
{command
TEXT270 (or T270)
Prints text (vertically) rotated 270 degrees
counterclockwise
{font
font의 Name/number
{size
font의 size
{x
Horizontal starting position
{y
Vertical starting position
{data
The text to be printed
Otros manuales para LK-P20II
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora de SEWOO
SEWOO
SEWOO SLK-TL32X Series Manual de usuario
SEWOO
SEWOO LK-P21 Manual de usuario
SEWOO
SEWOO LK-P12W Manual de usuario
SEWOO
SEWOO LK-P25 Manual de usuario
SEWOO
SEWOO LUKHAN LK-P21B Manual de usuario
SEWOO
SEWOO SLK-TL12X Series Manual de usuario
SEWOO
SEWOO LK-P31 Manual de usuario
SEWOO
SEWOO LK-P20W Manual de usuario
SEWOO
SEWOO SLK-T21EB Series Manual de usuario
SEWOO
SEWOO LK-T210 Manual de usuario
SEWOO
SEWOO SLK-T213EB Series Manual de usuario
SEWOO
SEWOO LUKHAN LK-P21B Manual de usuario
SEWOO
SEWOO SLK-TL100 Manual de usuario
SEWOO
SEWOO LK-P SERIES Hoja de instrucciones
SEWOO
SEWOO LK-P43W Manual de usuario
SEWOO
SEWOO LK-P30W Manual de usuario
SEWOO
SEWOO LK-P400 Manual de usuario
SEWOO
SEWOO LK-P43II Manual de usuario
SEWOO
SEWOO SLK-TL122 Manual de usuario
SEWOO
SEWOO SLK-TE21X Series Manual de usuario
