SeeMeCNC Rostock MAX v2 Manual de usuario

SeeMeCNC Guides

Rostock MAX v2 RTP User Guide

This How-To will get you started with your new Factory Assembled Rostock Max v2 3D Printer

from SeeMeCNC. It will cover: Unpackaging and Setup, Software Install, Setup, and How to

Operate your new 3D Printer, and Getting Connected.

Written By: JJ Johnson

Rostock MAX v2 RTP User Guide

Step 1 — Unpackaging and Setup

Your machine was fully assembled, calibrated and printed successfully before it left our factory.

We have done some things to make sure the machine does not get damaged while shipping the

printer. Please complete the following steps



Carefully remove all shrink wrap from the printer. Be careful not to cut the machine if you are using

a knife.



The arms have been inverted to prevent the hot end nozzle from striking the glass print surface

during shipping. To invert the arms from shipping position to printing position, place your hand on

ONE of the carriages and slowly move this carriage upward toward the top of the printer.



Next select one of the two remaining carriages and repeat.

Do the same operation with the final carriage.

Remove the BLUE calibration print from the print bed. (we leave that on there for you to see that

your printer has been calibrated and printed on and is ready for printing)



Rostock MAX v2 RTP User Guide

Step 2 — Unpackaging and Setup Continued

The spool holder has been removed from the machine and you will need to reinstall it. Locate the

spool holder and insert the 3 nylon lock nuts as shown in the second image.



Finally, position the spool holder on the top of the machine as shown in the third image. Use the (3)

6-32 x 1” machine screws to secure the spool holder to the top plate.



Step 3 — Unpackaging and Setup Continued

Install the spool holder arms as

shown in the image.



Rostock MAX v2 RTP User Guide

Step 4 — Unpackaging and Setup Continued

Install the AC power cord

Install the USB cable (Note: the front left piece of acrylic has been removed in the image to make

the location of the USB port more easily recognized. You can easily gain access to this location by

removing the front LCD Controller Module. This module is fastened to the machine with (2) nylon

thumb screws.)



Rostock MAX v2 RTP User Guide

Step 5 — Software Install, Setup, and How to Operate your new 3D Printer

Download: Rostock Max v2 User Manual

Familiarize yourself with the READ ME FIRST section on page 2

Perform the driver installation as instructed on pages 5-6

YOU DO NOT NEED TO PERFORM THE STEPS ON PAGES 7-12. THE PRINTER'S FIRMWARE

IS ALREADY LOADED ONTO THE RAMBO BOARD.



Familiarize yourself with the LCD and Front Panel Controls on pages 13-15

Install and configure MatterControl as directed on pages 17-22

YOU DO NOT NEED TO PERFORM THE INITIAL FUNCTION TESTS ON PAGES 23-35. YOUR

PRINTER IS ALREADY FULLY CONFIGURED AND CALIBRATED



Get some practice printing! Pages 36-42 in the manual will teach you how to print a fan shroud on

your new printer. This part is already installed on your printer, however this will be good practice

for learning how to operate the software and printer.



Rostock MAX v2 RTP User Guide

Step 6 — Software Operation

Read through the remainder of the

manual about:



MatterControl Basics: Slicing

(pages 53-62)



MatterControl Basics: Loading

and Printing Objects (pages 63 -

68)



Advanced MatterControl:

Configuration (pages 69 - 82)



Advanced MatterControl: Settings

- Filament (pages 83 - 86)



Advanced MatterControl: Settings

- Printer (pages 87 - 89)



Using the 3D and Layer Views

(pages 90 - 98)



A Strategy for Successful (and

Great!) Prints (pages 99 - 112)



Rostock MAX v2 RTP User Guide

This document was last generated on 2017-06-18 10:31:06 PM.

Step 7 — Getting Connected

Join our community of 3D Printing enthusiasts by visiting www.forum.seemecnc.com

Should you need any customer support, please visit SeeMeCNC and submit a support ticket.

Chat with live technicians Monday - Friday 8am - 4pm EST.

Rostock MAX v2 RTP User Guide

Otros manuales para Rostock MAX v2

Tabla de contenidos

Otros manuales de Impresora 3D de SeeMeCNC

SeeMeCNC

SeeMeCNC Artemis Manual de usuario

SeeMeCNC

SeeMeCNC Artemis 300 Manual de usuario

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manual de usuario

SeeMeCNC

SeeMeCNC Rostock Max Manual de usuario

SeeMeCNC

SeeMeCNC DropLit Manual de usuario

SeeMeCNC

SeeMeCNC rostock max v2.0 Manual de usuario

SeeMeCNC

SeeMeCNC orion delta Manual de usuario

SeeMeCNC

SeeMeCNC ERIS DELTA Manual de usuario

SeeMeCNC

SeeMeCNC Delta Manual de usuario

SeeMeCNC

SeeMeCNC orion delta Manual de usuario

SeeMeCNC

SeeMeCNC Rostock Max v3 Manual de usuario

SeeMeCNC

SeeMeCNC Rostock Max v3 Manual de usuario

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manual de usuario

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manual de usuario

SeeMeCNC

SeeMeCNC orion delta Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario