Securitytronix ST-WD600PTZMINI Manual de usuario

v2.2 7/28/11

INSTALLATION MANUAL

ST-WD600PTZMINI

Vandalproof Intelligent Dome PTZ

Color Camera

v2.2 7/28/11

PACKAGE CONTENTS

This package contains:

One ST-WD600PTZMINI vandalproof intelligent dome color camera

One installation manual

Note: The ST-WD600PTZMINI requires a minimum 12VDC 500mA power supply such as the

ST-PS12VDC1A or ST-PS12VDC2A.

PRODUCT DESCRIPTION

The ST-WD600PTZMINI is a professional grade IP66-rated outdoor dome color camera with pan,

tilt and zoom (PTZ) capability of 600TVL of resolution. The camera’s full digital design allows the

saving of all settings in non-volatile memory. The camera features include a 5mm –15mm

varifocal lens.

SPECIFICATIONS

ST-WD600PTZMINI

Specifications (Typical)

1. Image Sensor

1/3” SONY Super HAD CCD II

2. Resolution

600TVL

3. Lens

5mm –15mm auto focus lens

4. Effective Picture Elements

811x508

5. Minimum Illumination

0.001 Lux

6. Scanning System

2:1 interface

7. Video Output

1.0VP-P, 75Ω

8. Signal to Noise Ratio

>48dB

9. Synchronous System

Internal, Negative synch

10. Auto Electronic Shutter

1/60s ~ 1/100,000s

11. Gama Correction

0.45

12. Auto Gain Control

Auto

13. Power

DC12V 500mA

14. Operating Relative Humidity

95% maximum

15. Operating Temperature

14°F –113°F

16. Dimensions

4.8”x7”

17. Weight

3.3 lbs

v2.2 7/28/11

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this

unit. No user serviceable parts are inside.

CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than

specified power source.

1. UNPACKING and HANDLING

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the container before discarding packing material

2. MECHANICAL INSPECTION

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is

clean, and no connectors are broken, damaged, or loose. If equipment appears to be

damaged or defective please contact your distributor or Securitytronix at 1-610-429-1511 for

assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient

space between the camera’s power supply and video line and any high voltage

equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera

towards the sun or strong light.

c. Do not install the camera in an environment where the temperature is above 113°F.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Do not mount the camera near a radiator or heater.

f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe

gently with a mild detergent. Never use strong or abrasive detergents.

g. A minimum 12VDC 500mA power supply must be used. AC power cannot be applied.

Using an AC or other incorrect power supply will damage the camera.

h. Only qualified installers are allowed to install, test and disassemble the camera.

i. The camera is a low voltage product. If installed outdoors proper safety and lightening

grounding are required.

This symbol is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions.

This symbol is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electrical shock.

v2.2 7/28/11

4. WIRING CONNECTIONS

a. Connect the power supply’s DC plug to the camera’s power outlet.

b. Connect the camera to the monitor with a 75Ωcoaxial video cable.

c. Connect unshielded twisted pair (UTP) control cable between the camera’s RS485

port and the PTZ controller. Be sure wire polarities are the same at each connection.

The camera’s violet wire (A) is + positive and the white wire (B) is –negative.

d. Connect power supply’s AC plug to a suitable AC power outlet.

e. Adjust the lens direction according to the required surveillance area and environment.

v2.2 7/28/11

5. SETTING CAMERA ADDRESS, PROTOCOL and BAUD RATE USING DIP-SWITCHES

Camera address, protocol and baud rate can be set using the camera’s OSD menus and a

PTZ controller connected to the camera or using the camera’s onboard DIP-switches. To use

the camera’s DIP-switches, open the camera’s top cover. The switches are mounted on the

camera’s printed circuit board. There are 10 DIP-switches:

Switches 1 through 6 are used to set the camera address.

Switches 7 and 8 are used to set the camera baud rate.

Switch 9 is used to set the camera protocol.

Switch 0 is used to set RS485 terminal resistance.

DIP-switch settings are 1 = ON, 0 = OFF.

a. Setting Camera Address: DIP-Switches 1, 2, 3, 4, 5, 6

Camera No.

DIP-Switch Setting

Camera No.

DIP-Switch Setting

1 0 0 0 0 0

1 0 0 0 1 0

0 1 0 0 0 0

0 1 0 0 1 0

1 1 0 0 0 0

1 1 0 0 1 0

0 0 1 0 0 0

0 0 1 0 1 0

1 0 1 0 0 0

1 0 1 0 1 0

0 1 1 0 0 0

0 1 1 0 1 0

1 1 1 0 0 0

1 1 1 0 1 0

0 0 0 1 0 0

0 0 0 1 1 0

1 0 0 1 0 0

1 0 0 1 1 0

0 1 0 1 0 0

0 1 0 1 1 0

1 1 0 1 0 0

1 1 0 1 1 0

0 0 1 1 0 0

0 0 1 1 1 0

1 0 1 1 0 0

1 0 1 1 1 0

0 1 1 1 0 0

0 1 1 1 1 0

1 1 1 1 0 0

1 1 1 1 1 0

0 0 0 0 1 0

0 0 0 0 0 1

b. Setting Camera Baud Rate: DIP-Switches 7, 8

Baud Rate

Switch 7 8

1200bps

1 0

2400bps

0 0

4800bps

1 1

9600bps

0 1

c. Setting Camera Protocol: DIP-Switch 9

Protocol

Switch 9

PELCO-P

PELCO-D

d. Setting RS485 Terminal Resistance: DIP-Switch 0

RS485 Resistance

Switch 0

Connect to 120ΩResistor

No Connection to 120ΩResistor

v2.2 7/28/11

6. SETTINGS USING CAMERA’s ON SCREEN DISPLAY MENU

v2.2 7/28/11

7. FUNCTIONS

The camera uses preset commands to achieve a number of functions. CLEAR / SET / GOTO

and the preset number to perform these functions.

Set Preset Point Numbers:

Preset No.

Function

1 –32

Set Preset Point

Set Left Limited Point

Set Right Limited Point

Set Home Point

Set Home Point Wait Time to 64

Set Home Point Wait Time to 128

Set Home Point Wait Time 192

Set Home Point Wait time to 255

Enable auto return to Home Point

Disable auto return to Home Point

Set Left Limited Point

Set Right Limited Point

Reset Original Point

240

Clean Setup

241

Initialize System

242

Start PATTERN Setup

243

End PATTERN Setup

247

Start PATTERN

248

Stop PATTERN

Clear Preset Point Numbers:

Preset No.

Function

1 –32

Clear Preset Point

Clear Left Limited Point

Clear Right Limited Point

Clear Home Point

Clear Left Limited Point

Clear Right Limited Point

GoTo Preset Point Number:

Preset No.

Function

1 –32

GoTo Preset Point

GoTo Pan Zero Point

GoTo Home Point

GoTo Left Limited Point

GoTo Right Limited Point

Start Auto Scan

v2.2 7/28/11

To Set and Run a Pattern:

a. Input SET preset 242 to begin pattern learning.

b. Send GOTO preset command so the camera will recognize this point as a pattern

point. For example, if the camera is to tour at point 1, 3, and 6 input GOTO preset

point 1, GOTO preset point 3 and GOTO preset point 1.

c. Input SET preset 243 to end pattern learning.

d. Input SET preset 247 to start pattern tour.

e. Input SET preset 248 to stop pattern tour.

8. TROUBLESHOOTING

a. No picture after applying power –(i) check all plugs and cables are securely

connected to the proper connectors; (ii) ensure your power supply is providing the

correct voltage and current.

b. The picture has ripples –(i) check to see if the power supply is experiencing AC ripple,

if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if

other peripheral equipment is causing ripple and if so make the necessary

adjustments.

c. The picture background continuously changes color –a fluorescent lamp’s magnetic

field may cause color roll, therefore, reduce the number of fluorescent lamps or

increase the distance between the camera and the lamps.

d. The picture appears smeared –(i) the power supply voltage level may be unstable,

therefore, try another power supply; (ii) ensure the cables are correctly connected

and/or the cables are of the correct impedance.

e. Other interference may require a Securitytronix ground loop isolation filter.

f. Power is on, but the controller does not work –(i) check to make sure the DIP

switches for address and communications baud rate are properly set, (ii) check to

ensure the RS485 connections at the camera and the PTZ Controller have the same

polarity, (iii) check the integrity and continuity of the unshielded twisted pair (UTP)

control cable.

g. Additional troubleshooting assistance can be found on-line at www.securitytronix.com

in addition to support from Securitytronix sales engineers at 1-610-429-1511.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Securitytronix

Securitytronix

Securitytronix ST-PTZMINI-IR10XTA Manual de usuario

Securitytronix

Securitytronix ST-BTWD600IR2812 B Manual de usuario

Securitytronix

Securitytronix ST-D600IRVP2812 Manual de usuario

Securitytronix

Securitytronix ST-BT6003.6-W2 Manual de usuario

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2PTZ Manual de usuario

Securitytronix

Securitytronix ST-IP2PTZ Manual del operador

Securitytronix

Securitytronix ST-BT540IR50VFDV-B Manual de usuario

Securitytronix

Securitytronix ST-D600IR2812-HB Manual de usuario

Securitytronix

Securitytronix ST-D540IRVP2812 Manual de usuario

Securitytronix

Securitytronix ST-D700IR2812-B/W Manual de usuario

Securitytronix

Securitytronix ST-BTLI540IR20 Manual de usuario

Securitytronix

Securitytronix ST-PTZ650FM-23X Manual de usuario

Securitytronix

Securitytronix ST-IP4FWD Manual de usuario

Securitytronix

Securitytronix ST-PTZ480-22 Manual de usuario

Securitytronix

Securitytronix ST-DLI420IR6-B Manual de usuario

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2FD Manual de usuario

Securitytronix

Securitytronix ST-D600DNVP2812 Manual de usuario

Securitytronix

Securitytronix ST-IP-BT3.6-1 Manual de usuario

Securitytronix

Securitytronix ST-D4203.6B Manual de usuario

Securitytronix

Securitytronix ST-DLI540IRVP-B Manual de usuario

Securitytronix

Securitytronix ST-HD-BT2812M-2MP Manual de usuario

Securitytronix

Securitytronix ST-IP2VFB Manual de usuario

Securitytronix

Securitytronix ST-CVTMD420-WPIR-W Manual de usuario

Securitytronix

Securitytronix ST-BT540IR30VF Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario