Securam ProLogic B22 Manual de usuario
ProLogic B22 Operation Instructions
Document No: EC-1701A-B22-190502
Version No: V1.0
1.0 System Installation
1.1 System Components
1.2 Pairing the EntryPad with the Lock
1.3 Lock and EntryPad Installation
1.4 Installing Battery
1.5 Test Lock Operation
2.0 Lock Operation
2.1 Opening the Lock (Static Codes)
3.0 Set Date and Time
3.1 Set Clock Time
4.0 Code Management
4.1 Change Code
4.2 Enroll Manager 2
4.3 Enroll New User
4.4 Delete One User
4.5 Delete All Users
4.6 Delete Phone
5.0 Smartphone Management
5.1 Pair Phone
5.2 Delete Phone
6.0 System Identification
6.1 System Info
7.0 Lock Settings
7.1 Factory Reset (Firmware)
7.2 Show Audit Trail
7.3 Enable/Disable Vibration Sensor
7.4 Set Vibration Sensitivity
7.5 Set Battery Efficiency
8.0 Data Management
8.1 Encryption Key Set
9.0 Recovering the System –Reset to Default
9.1 Recovery Code Set
9.2 Recover System
9.3 Mechanical Reset
10.0 Shortcut Operations
10.1 Add User
10.2 Delete User
11.0 Menus
12.0 Specification
13.0 Precaution
14.0 Certification
15.0 Packing List
16.0 FCC Warning
ProLogic B22 Operation Instructions
2
1.0 System Installation
1.1 System Components
The system consists of (1) EntryPad –Part # EC-1701A-B22 plus (1) Lock body as follows:
SwingBolt –Part # EL-0601
SwingBolt with Status–Part # EL-0601-S
DeadBolt –Part # EL-0701
SpringBolt –Part #EL-0801
1.2 Pairing the EntryPad and the Lock
SecuRam safe lock systems can operate in two different modes depending upon the type of EntryPad
being used with the lock body. The ProLogic B22 is a digital lock system and therefore the lock must also
be programmed in digital mode. Both modes follow the same steps to reset / set which is done by
following the steps detailed below:
Step 1: Ensure the battery is connected to the Entry Pad.
Step 2: Ensure the lock cable is disconnected from the lock body.
Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).
Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate
any latent energy in the lock.
Step 5: Now depress the reset button and hold.
Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.
Step 7: Continue to hold down the reset button for 5 seconds and then release.
Step 8: Verify that the pairing is complete by opening the lock with the default code
111111.
Step 9: Press any button on the EntryPad to initiate a lock communication test. The EntryPad
will display the following information:
Followed by:
Enter a valid code to test the lock.
The Default codes are as follows:
Super Code (ID00) is 111111
Manager Code (ID01) is 123456
ProLogic B22 Operation Instructions
3
*Note: In many cases, the Super Code (ID00) is changed from default and maintained by the
safe manufacturer as a reset code for your security.
If you have difficulty resetting the lock, please call SecuRam Tech Support at (805) 988-8088 or email
techsupport@securamsys.com.
1.3 Lock and EntryPad Installation
Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.
Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle
hole.
Now insert the lock cable (attached to the EntryPad) through the spindle hole.
On the backside of the safe door, you will see the lock mounting plate and the predrilled lock
mounting holes.
Connect the lock cable to the lock body and position the lock body appropriately on the lock
mounting plate.
Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This
channel is provided to protect the lock cable from damage or crimping during installation.
Using the provided lock bolts, secure the lock body to the mounting plate.
Note: it is very important to ensure that there is an adequate gap between the lock bolt and the bolt
work. This gap must be 0.125”.
1.4 Installing the Battery –SureLock Battery Compartment (removable battery compartment)
Locate the SureLock Battery Compartment at the 5 o’clock position of the EntryPad. See Fig. 3.
Release the latch of the battery compartment, by pulling lever downward. See Fig 4.
Pull out the battery compartment from the bottom of the EntryPad. See Fig 5.
Install a new 9V alkaline battery (Duracell or Energizer brands are recommended) into the
compartment. The battery compartment will only receive the battery when the positive and
negative terminals are oriented correctly. See Fig. 6
Put the battery compartment back into the EntryPad. Push the latch of the battery
compartment up until it snaps closed. See Fig. 3
ProLogic B22 Operation Instructions
4
1.5 Testing the Lock Operation
The ProLogic B22 comes with two factory default codes:
•Super Code (ID00) is 111111
•Manager Code (ID01) is 123456
Enter one of the valid codes to verify the communication between the lock and EntryPad. The lock will
open.
2.0 Lock Operation
Upon initial power up, the LCD screen starts a communications test as shown below:
Model Number
Software Version Number
No. of Users/ No. Users Programmed
Lock Status
After this initial power up, it will check to ensure that the system is communicating correctly. The
display will read “Link with Lock OK”.
If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the Entrypad and
the Lock”
2.1 Opening the Lock
The safe lock system has two default codes installed as follows:
•Super Code (ID00) 1-1-1-1-1-1
•Manager Code (ID01) 1-2-3-4-5-6
Step 1: Enter a valid code, then press the Menu/OK button. The display will read “Manager or
[Name] Verified” and the Lock will open.
The display will read:
The lock will relock after 6 seconds.
All codes for (ID 00 –ID 03) work in this manner.
ProLogic B22 Operation Instructions
5
Note: with the B22 you have the opportunity to mask your code, in case someone is watching you
enter your code. On the EntryPad you can enter up to 9 digits –your 6 digit code plus up to 3
additional digits to mask your code.
For example, if your code is 1-2-3-4-5-6,
Enter 1-2-3-4-5-6 and Press Menu/OK button to open
Enter 3-4-1-2-3-4-5-6-7, where the 2 masking digits before your code (3-4) and the single
masking digit after your code (7) are concealing or masking your actual code.
If you enter less than 9 digits, you must always press the Menu/OK button to send the code to
the lock.
Note: the additional 3 masking digits can be added before and/or after your code.
3.0 Set Date and Time
3.1 Set Clock Time
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: Scroll “▼” to the menu selection “Set Time” and Press OK
Step 5: Each of the elements of the date and time will flash when it is available to be set. Use the
“▼”or “▲” to scroll to the correct value and Press OK to move to the next element.
4.0 Code Management
The ProLogic B22 comes with two default codes:
•Super Code (ID00) is 111111
•Manager Code (ID01) is 123456
It is strongly recommended that both these default codes are changed before the lock system is put into
service.
ProLogic B22 Operation Instructions
6
4.1 Change Code
The B22 has 2 codes by default:
Super Code: 1 1 1 1 1 1
Manager Code: 1 2 3 4 5 6
Note: The default codes must be changed before usage; otherwise you cannot add new users or pair the
lock to the APP.
Please follow the steps below to change the code:
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: Scroll “▼” to the menu selection “Change My Code” and Press Menu/OK
Step 5: Enter the new 6 digit code. Note: Code cannot be set to 1 1 1 1 1 1 or 1 2 3 4 5 6
Step 6: Repeat the new 6 digit code.
The New Code has now been saved and is available for use.
4.2 Enroll Manager 2
The ProLogic B22 can add a second Manager and one User, in addition to the default codes.
ProLogic B22 Operation Instructions
7
Note: Manager Codes have full access to the programming menu. The User Code only has access to the
change code menu option, and cannot modify any lock settings.
Step 1: Press the Menu/OK button.
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 5: Next the screen will show “Enroll Manager2”. Press Menu/OK
Note - Manager2 must be enrolled before you can enroll the user code (ID03)
Step 6: Now enter a 6 digit code
Step 7: Repeat new 6 digit code
Step 8: System will verify that code has been saved.
The new code is now enrolled and available to be used to open the lock.
4.3 Enroll New User
ProLogic B22 Operation Instructions
8
After Manager 2 User has been added, you can add a User.
Step1: Press the Menu/OK button.
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 5: Next the screen will show “Enroll New User”. Press Menu/OK
Step 6: Now enter a 6 digit code
Step 7: Repeat new 6 digit code
Step 8: System will verify that code has been saved.
The new code is now enrolled and available to be used to open the lock.
4.4 Delete One User
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
ProLogic B22 Operation Instructions
9
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: After entering a valid Super or Manager code, the screen will show “Users”.
Press Menu/OK.
Step 5: Scroll “▼”or “▲” to the menu selection “Delete One User” and Press Menu/OK
Step 6: Press the "Menu/OK" button first, then select the user to be deleted through the "▼" or
"▲" button, and finally press the "Menu/OK" button to prompt the screen:
Step 7: Press Menu/OK
This User Code is now deleted from the system.
4.5 Delete All Users
This feature is used to delete all users from the system. Upon executing this command, all users will be
deleted and Manager Code will be reset to default: Manager Code (ID01) 123456
Note: Super Code will not be changed to default, only recover system operation can do this.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
ProLogic B22 Operation Instructions
10
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Step 4: After entering a valid Super or Manager code, the screen will show “Users”.
Press Menu/OK.
Step 4: Scroll “▼”or “▲” to the menu selection “Delete All Users” and Press Menu/OK
Step 5: Press the "Menu/OK" to confirm
Step1: Press the Menu/OK button
Now all users are deleted.
5.0 Smartphone Management
The ProLogic B22 uses a smartphone to allow for remote management and control. Download the
SECURAM app on the App Store for iPhones or on the Google Play Store for Android.
5.1 Pair Phone
This feature is used to pair a smartphone to the system. This option will only appear after the default
code has been changed.
To begin, please download SECURAM Smart Home APP.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to enter a code, enter a valid Super or Manager Code, and
press Menu/OK.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cerrar de Securam
Securam
Securam SafeLogic Basic Series Manual de usuario
Securam
Securam SafeLogic Xtreme Manual de usuario
Securam
Securam SCANLOGIC FPC-1808-II-MB Manual de usuario
Securam
Securam ScanLogic B22 Manual de usuario
Securam
Securam SafeLogic Xtreme Manual del propietario
Securam
Securam ProLogic L02-C Manual de usuario
Securam
Securam ProLogic B01 Manual de usuario
Securam
Securam D Series Manual de usuario
Securam
Securam ProLogic L22 Manual de usuario
Securam
Securam FPC-0601A-D22 Manual de usuario
Securam
Securam EM-1701A-R Manual de usuario
Securam
Securam SH-WB01 Manual de usuario
Securam
Securam ScanLogic D66 Manual de usuario
Securam
Securam ScanLogic Optical Manual de instalación
Securam
Securam ECSL-601 Manual de usuario
Securam
Securam ProLogic L22 Manual de usuario
Securam
Securam SH-TB01 Manual de usuario
Securam
Securam SafeLogic Basic Manual de usuario
Securam
Securam MANAGER Series Manual de usuario
Securam
Securam ProLogic L01 Manual de usuario
