Sauter TC 1250-0.1F Manual de usuario

Sauter GmbH

Ziegelei 1

D-72336 Balingen

e-mail: info@kern-sohn.com

Phone : +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.sauter.eu

Instruction Manual Digital Coating

Thickness Gauge

SAUTER TC

Version 2.0

04/2020

TC-BA-e-2020

PROFESSIONAL MEASURING

2 TC-BA-e-2020

SAUTER TC

V. 2.0 04/2020

Instruction Manual Digital Coating Thickness

Gauge

Thank you for purchasing a digital coating thickness gauge from SAUTER. We hope

you will be very satisfied with the high quality of this measuring device and its extensive

functionality. For any questions, wishes and suggestions please do not hesitate to

Table of contents:

1. Introduction.................................................................................................... 3

1.1 General description.................................................................................................................. 3

2. Functions........................................................................................................ 3

3. Technical data................................................................................................ 3

4. Description of the control panel................................................................... 5

5. Measuring procedure .................................................................................... 5

6. Zero adjustment............................................................................................. 6

7. Battery replacement ...................................................................................... 6

8. Adjusting foils................................................................................................ 7

9. General notes................................................................................................. 7

10. Restore factory settings................................................................................ 7

11. Notes............................................................................................................... 8

TC-BA-e-2020 3

1. Introduction

1.1 General description

This coating thickness gauge is small, light and handy. Although it has complex and

advanced equipment, it is convenient and easy to use.

Its robustness allows it to be used for many years, provided that all instructions in this

manual are carefully followed.

Therefore please keep them always within reach!

Note: It is strongly recommended to adjust the new meter before first use, as

described in chapter 6. This will result in a higher measurement accuracy from

the beginning.

2. Functions

"This device complies with the ISO- Norm 2360 as well as the DIN-Norm, ASTM and

BS. This means that it can be used both under laboratory conditions and under rough

environmental conditions "in the field".

"The F" probe measures the thickness of non-magnetic layers, e.g. paint, plastic,

enamelled porcelain, copper, zinc, aluminium, chrome, lacquer layers etc.

These layers should be on magnetic materials such as steel, iron, nickel, etc. This

probe is often used to measure the thickness of galvanized layers, lacquer layers,

enamelled porcelain layers, phosphorescent layers, copper plates, aluminium plates,

alloys, paper, etc.

"The N- probe measures the thickness of non-magnetic layers on non-magnetic

metals.

It is used to measure anodizations, lacquer layers, glazes, colours, enamel, plastic

layers, powder coating etc. These should be on non-magnetic substrates such as

aluminium, sheet metal, non-magnetic stainless steel and others.

"The FN measuring probe is a combination of both probes and is therefore defined for

both areas of application

"Automatic recognition of the carrier material

"Manual or automatic switch-off to conserve battery power.

"Metric/ imperic conversion of the measured values of µm/mil

"Two measuring modes: - single and continuous (S= single/ C= continuous)

"Wide measuring range and high resolution

" Can be connected to a PC for data transfer via RS 232 interface

Cable and software are available as optional accessories (ATC-01).

3. Technical data

TC 1250-0.1F

TC 1250-0.1FN

TC 1250-0.1N

Display

4 digits, 10mm LCD display with backlight

Measuring range

0 to 1250 μm / 0 to 50 mil (standard)

4 TC-BA-e-2020

Resolution

0,1 µm (0 to 99,9 µm), 1 µm (over 100)

Measurement

uncertainty

3 % of the measured value or Min ± 2,5 µm.

Applies within the tolerance band of ± 100 µm

around the typical measuring range if a two-point

calibration was also performed within this

tolerance band

off-set accuracy

1 % of the measured value or min. 1,0 μm

Applies within ± 50 μm around the offset Accur

Point

PC connection

RS-232 interface

Power supply

4x1.5 AAA batteries (UM-4)

Ambient

temperature

0°C to 50°C

Air humidity

≤80%

Dimensions

126 x 65 x 27mm

Weight

Ca 81g (without batteries)

Scope of delivery

Carrying case, operating instructions

Depending on the type:

1. built-in measuring probe F: TC 1250-0.1 F, with

F/N key

2. built-in measuring probe N: TC 1250-0.1 N, with

F/N key

3. built-in measuring probe FN: TC 1250-0.1 FN,

without F/N u.S/C key

- Spacer foils, for each model

- Zero plate (aluminium) for model N

- Zero plate (iron) for model F

- 2 zero plates (aluminium and iron) for model FN

(combination unit)

Optional accessories: Software and cable RS-

232C: ATC-01

Attention: All accuracy specifications apply after adjustment!

TC-BA-e-2020 5

4. Description of the control panel

Model TC-F and TC-N Model TC-FN (Combi Model)

4-1 Measuring probe: F, N, or FN

4-2 Display

4-3 Zero key

4-4 Plus button

4-5 Minus key

4-6 On and Off button (multifunctional)

4-7 µm/ mil Changeover key (shortcut key)

4-8 Battery compartment / cover

4-9 S/C measuring mode button (single/continuous)

4-10 Connector for RS-232C connection

4-11 F/ NF- key

5. Measuring procedure

a) Switch on by pressing the on/off button 4-6. '0' appears on the display 4-2.

The TC 1250-0.1FN meter recognizes the setting of the last measurement itself by the

symbol 'Fe' (= F) for ferrous metals or 'NFe' (= N) for non-ferrous metals shown on the

display. It switches to the automatic measuring mode, which also correctly recognizes

and assigns the zero plate or any other substrate itself.

b) Place the measuring probe 4-1 on the layer to be measured. The layer thickness

can now be read on the display. The reading result can be corrected by pressing the

plus key 4-4 or the minus key 4-5. For this purpose, the measuring probe should not

be in close proximity to the layer to be measured or the zero plate.

c) To take the next measurement, simply raise the measuring probe 4-1 by more than

1cm, the display will show "0" again and step b) will be repeated.

4-10

4-2

4-5

4-3

4-4

4-1

4-4

4-5

4-6

4-8

4-9

4-8

4-7

4-10

4-2

4-11

6 TC-BA-e-2020

d) In case of possible inaccuracies in the measurement result, it is recommended to

adjust the measuring instrument before measurement, as described in chapter 6.

e) On the one hand, the device can be switched off with the on/off button 4-6.

Otherwise, it switches itself off 80 seconds after the last key is pressed.

f) The measuring unit can be displayed in µm or mil. The changeover is made as

follows:

- By pressing the changeover key 4-7 or

- the on/off key 4-6 is pressed and held until 'UNIT' is shown on the display and then

the zero key 4-3 is pressed. The measuring unit changes over to the other one when

the on/off key is released again.

This process takes a total of 7 seconds (from pressing the zero or on/off button).

g) To change to the measuring mode from 'simple' to 'continuous' or vice versa, the

zero or on/off key 4-6 must be pressed and held down until 'SC' appears in the display.

Then the zero key 4-3 ispressed. The symbol ((-)) stands for the continuous measuring

mode and 'S' for the simple measuring mode. This process takes 9 seconds (from

pressing the on/off button).

6. Zero adjustment

a) The zero adjustment for 'Fe' (=F) and 'NFe' (=N) should be done separately. The

iron zero plate is taken when 'Fe' is read on the display, while the aluminium zero plate

is taken when 'NFe' is read.

The measuring probe 4-1 is now carefully placed on the zero plate. The zero/on/off key

4-6 is pressed and '0' is shown in the display without lifting the probe.

Attention: The zero adjustment is useless if the measuring probe is not directly

on the zero plate or another, uncoated carrier material.

b) A suitable adjustment foil, which corresponds approximately to the measuring range,

must be selected.

appropriate uncoated substrate for the forthcoming tests.

d) Carefully press the measuring probe 4-1 in the middle of the standard foil and then

lift it off again. The reading on the display corresponds to the measured value of the

layer thickness.

This reading can be corrected by pressing the plus key 4-4 or the minus key 4-5. This

should be done if the probe is not in the nearer vicinity of the zero plate or the

corresponding carrier material.

e) The procedure described in d) should be repeated until the result is correct.

7. Battery replacement

TC-BA-e-2020 7

a) When the battery symbol ``+/-`` appears on the display, the batteries should be

replaced.

b) The battery cover 4-8 is removed from the meter and the batteries are removed.

c) The batteries (4x1.5 V AAA/UM-4) are inserted by observing the polarity when

inserting them.

d) If the device is not used for a longer period of time, the batteries should be removed.

8. Adjusting foils

This instrument includes an adjustment foil set with different foils and measuring

ranges, but always covers the measuring range from 20 to 2000µm. These are also

available as optional accessories, article ATB-US07

9. General notes

a) The measuring instrument should always be adjusted on the base material used for

the actual measurement, if possible, instead of on the supplied zero plate F made of

steel or N made of aluminium. This makes the measuring accuracy more accurate from

the outset.

b) The measuring probe may wear out. The lifetime of it usually depends onthe number

of measurements and the roughness of the layer to be measured. The replacement of

a measuring probe should only be carried out by qualified personnel

can be carried out.

10.Restore factory settings

a) It is recommended that the factory settings be performed in the following cases:

- no more measurements can be made at all

- the measuring accuracy is impaired due to drastic changes in the environment in

which the measuring instrument is used

- After replacing the measuring probe

(b) Procedure:

The factory settings include both the settings for "Fe" (F) and for "NFe" (N).

Please note which symbol is shown on the display.

Only one setting at a time can be made, as follows:

- Press the on/off button 4-6 and do not release it until the display shows "CAL". It

takes about 5 seconds from the start of this button operation until CAL is displayed.

The measuring probe 4-1 is carefully pressed onto the corresponding carrier material.

Then the zero key is pressed, which is accompanied by a beep.

When NF:H appears on the display, the measuring probe 4-1 is raised by more than 5

cm.

Then the zero button is pressed again and the meter returns to the measuring mode.

The factory settings are now complete.

Note: This process should always be completed within the following 6 seconds.

Otherwise, it will be automatically interrupted by the unit and the reset will be invalid.

8 TC-BA-e-2020

11.Notes

With the LN function, the linearization of the measuring instrument specified by the

calibration can be changed. However, it is strongly recommended not to make any

changes to the LN value, as this change will lead to deviating measurement results.

Any change in the Ln value can significantly affect the measuring accuracy. This

value should only be set by qualified personnel.

In general, the larger the Ln value, the smaller the reading result for the same layer

thickness. A small change of the Ln- value causes a large change in the reading

result in the upper measuring range (at 500µm/ 20mil).

Thus the Ln value is to be corrected:

Pressing the on/off button: It takes about 11 seconds from the beginning of pressing

the on/off button.

Its value can be changed by pressing the Plus or Minus key after 'LN' appears in the

display and releasing the On/Off key. The value is stored and then the zero key is

pressed.

A: The reading result in the lower area is corrected by pressing the Plus or Minus key.

B: The Ln value is increased if the reading result is correct in the lower range (e.g.

51µm) but too large in the upper range (e.g. 432µm).

In contrast, the Ln value is reduced if the reading result is correct in the lower range

(e.g. 51µm) but too small in the upper range (e.g. 432µm).

C: This procedure of A. and B. is repeated until the reading result is satisfactory in its

accuracy for each distance foil.

Note:

To view the CE declaration, please click on the following link:

https://www.kern-sohn.com/shop/de/DOWNLOADS/

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de sauter

sauter

sauter TB Series Manual de usuario

sauter

sauter FK Series Manual de usuario

sauter

sauter TB Manual de usuario

sauter

sauter SW 1000 Manual de usuario

sauter

sauter FC Manual de usuario

sauter

sauter CD P2 Manual de instrucciones

sauter

sauter FT 1K Manual de usuario

sauter

sauter CP P1 Manual de usuario

sauter

sauter TC 1250-0.1 F Manual de usuario

sauter

sauter TPE-N Manual de usuario

sauter

sauter SW 1000 Manual de usuario

sauter

sauter CP P9 Manual de usuario

sauter

sauter SW 1000 Manual de usuario

sauter

sauter SAUTER TE SERIES Manual de usuario

sauter

sauter TB-US Manual de usuario

sauter

sauter TVP Manual de usuario

sauter

sauter TU 80-0.01US Manual de usuario

sauter

sauter FK 10 Manual de usuario

sauter

sauter modu840 Manual de usuario

sauter

sauter FA Manual de usuario

sauter

sauter SN Manual de usuario

sauter

sauter TE 1250-0.1F Manual de usuario

sauter

sauter TN-EE Manual de usuario

sauter

sauter TU-US Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

sauter TC 1250-0.1F Manual de usuario

Manuales populares de Instrumento de medición de otras marcas