Sartorius M3P Manual de usuario

Sartorius

M3P, M3P-000V001

Electronic Microbalances

Installation and Operating Instructions

M3P

1 Weighing pan 11 Menu access switch

(for the balance operating program)

2 Pan support 12 Tare control

3 Interior draft shield 13 CAL key

4 Interface 14 Weight display

5 Power receptacle 15 Manufacturer’s label

6 Level indicator 16 Spacer

7 Leveling foot 17 Perforated filter pan holder

(for large filter weighing pan)

8 ON/OFF key 18 Filter pan holder (for small filter weighing pan)

9 Print key 19 Small filter weighing pan

10 Range expansion key 20 Large filter weighing pan

M3P-000V001

Filter-Microbalance

1 Weighing pan 11 Menu access switch

(for the balance operating program)

2 Pan support 12 Tare control

3 Interior draft shield 13 CAL key

4 Interface 14 Weight display

5 Power receptacle 15 Manufacturer’s label

6 Level indicator 16 Spacer

7 Leveling foot 17 Perforated filter pan holder

(for large filter weighing pan)

8 ON/OFF key 18 Filter pan holder (for small filter weighing pan)

9 Print key 19 Small filter weighing pan

10 Range expansion key 20 Large filter weighing pan

Contents

Page

About the Product (Warranty) 5

Storage and Shipping Conditions 6

Equipment Supplied 7

Installation Instructions

Ambient Conditions 8

Connecting Electronic Devices (Peripherals) 8

Startup

Preparing the M3P for Operation 9

Preparing the M3P-OOOV001 Filter

Microbalance for Operation 9

Connecting the Balance to Line Power 10

Voltage Selection 11

Safety Precautions 11

Leveling the Balance using the Level Indicator 11

How to Operate the Balance

General Directions for Working with the Balance 12

Weight Display 13

Turning the Balance On and Off 13

Self-Test, Weighing 14

Weighing Filters on the M3P-000V001 14

Taring, Weighing with a Tare Container 15

Below-Balance Weighing 16

Auto Zero 16

Calibration 17

Internal Calibration 17

External Calibration 18

Balance Operating Program 19

Reading a Program Menu Code (List Mode) 19

Changing a Program Menu Code (Change Mode) 19

List of the Programmable Menu Code Settings 21

Troubleshooting Guide 22

Transporting the Balance

Transport Arrestment 23

Care and Maintenance

Cleaning 24

Safety Inspection 24

Accessories (Options) 25

Interface 26

Interfacing Devices with the Balance (RS Interface) 26

Specifications

Model M3P 27

Model M3P-000V001 28

About the Product (Warranty)

With this Sartorius Balance you have acquired a high-quality

electronic weighing Instrument that will ease your daily work-

load.

Please read these Installation and operating instructions care-

fully before operating your new balance.

Pursuant to the German Directive for the Implementation

of Regulations for Prevention of Accidents "Elektrische

Anlagen und Betriebsmittel (VBG 4)" [Electrical Installa-

tions and Equipment] of April 1986, it is hereby certified

that the equipment delivered, "Electronic Microbalance,

model M 3 P," is manufactured and tested in compliance

with the following DIN/VDE regulations

DIN IEC 348/VDE 0411 Safety requirements for elec-

tronic measuring apparatus DIN

IEC 380/VDE 0806 Safety of

electrically energized Office ma-

chines

DIN IEC 601/VDE 0750 Safety of medical electrical

equipment

and Article 10 of the Low Voltage Directive (73/23/EEC)

issued on February 19, 1973 by the European Commu-

nity. When you use electrical equipment in installations

and under ambient conditions requiring higher safety

Standards, you must comply with the provisions as speci-

fied in the applicable regulations for installation in your

country.

Do not miss out on the benefits of our full warranty.

Please complete the warranty card, indicating the date of Instal-

lation, and return the card to your Sartorius dealer.

Storage and Shipping Conditions

Allowable storage temperature range: -40°C...+70°C

-40°F... 158°F

The packaging of the balance has been designed to ensure that

the balance will not be damaged even if it is dropped from a

height of 80 cm (about 32 inches).

After unpacking the balance, please check it immediately for

any visible damage as a result of rough handling during ship-

ment. If this is the case, proceed as directed in the section enti-

tled "Safety Inspection."

Save all parts of the packaging and the box for shipping

your balance to prevent any damage during transportation.

In addition, please disconnect all connecting cables (e.g.

the plug on the power supply) to avoid damaging them.

Do not expose the balance unnecessarily to extreme tempera-

tures, moisture, shocks, blows or vibrations.

Equipment Supplied

M3P M3P-000V001

— balance

— kit of Standard

accessories

— portable

power supply

— dust cover

— Balance

— kit of Standard

accessories

— portable

power supply

— dust cover

— spacer

— 3 small filter weighing pans

(for filter diameters up

to70 mm or~ 2.8 in.)

— 3 large filter weighing pans

(for filter diameters from

70-100 mm or ~ 2.8-3.9 in.)

The M3P kit of Standard accessories contains the following:

1 weighing pan

1 pan support

1 interior draft shield

1 hanger for below-balance weighing

1 brush

1 pair of forceps

1 piece of lint-free cloth

The M3P-000V001 kit of Standard accessories contains the

following:

1 inferior draft shield

1 filter pan holder (for the small filter weighing pan)

1 perforated filter pan holder (for the large filter weighing pan)

1 standard-size weighing pan (22 mm Ø = ~ 1")

1 pan support (for standard-size weighing pan)

1 hanger for below-balance weighing

1 brush

1 pair of forceps

1 piece of lint-free cloth

Installation Instructions

Ambient Conditions

Microbalances are highly precise and very sensitive measuring

Instruments. Therefore, please choose a suitable place to set

up your balance. lt should not be exposed to the following:

- Heat radiation

- Aggressive/corrosive substances

- Vibrations

- Drafts

Use a balance table or a wall console (see "Accessories") to set

up your balance.

lf you wish to move your balance to another location,

please follow the directions on page 23 under "Transport-

ing the Balance."

Do not expose the balance to extreme moisture over long peri-

ods. Moisture in the air can condense on the surfaces of the

balance whenever a cold balance is brought to a substantially

warmer place.

lf you need to transfer the balance to a warmer area, make sure

to condition it for a few hours at room temperature. The best

way to prevent moisture condensation is to leave the balance

connected to line power. The components used in the balance

are rated to at least class KSF according to DIN 40040.

Your Sartorius Balance will provide accurate readouts even

when it is exposed to unfavorable ambient conditions.

You can adapt the balance to your requirements simply by

changing the menu code settings in the balance operating pro-

gram.

For this purpose, read pages 19 through 21

Connecting Electronic Devices (Peripherals)

Turn off the balance by pressing the ON/OFF key (8)

(STANDBY state), and wait until the weighing system of the

balance has been arrested automatically for transportation (see

also "Transporting the Balance" on page 23). Unplug the power

supply before you connect or disconnect devices to or from the

interface ports.

To reduce distortion of the weight readouts caused by ambient

conditions (turbulence within the weighing chamber, for exam-

ple), balance-generated data should be allowed to stabilize for

about 10 seconds before they are transmitted to an online

printer or other peripheral device.

Startup

Preparing the M3P for Operation

Remove the rubber band from the doors of the weighing cham-

ber. Place the interior draft shield (3) in the weighing chamber.

Use forceps to position the pan support (2) on the draft shield,

and place the weighing pan (1) on the pan support.

Preparing the M3P-OOOV001 Filter Microbalance for Opera-

tion

For weighing filters with diameters ranging up to 70 mm

(~ 2.8 in.):

— Slightly lift the cover of the weighing chamber and turn it

to the left or to the right

— Place the spacer (16) and the interior draft shield (3) in

the weighing chamber

— Use forceps to position the filter pan holder (non-

perforated) (18) and the small pan (19) for filter diameters

up to 70 mm (~ 2.8 in.)

Weighing filters with diameters ranging from 70 to 100 mm

(~ 2.8-3.9 in.):

— Slightly lift the cover of the weighing chamber and turn it

to the left or to the right

— Place interior draft shield (3) in the weighing chamber

— Use forceps to position the perforated filter pan holder

(17) and the large filter weighing pan (20)

Weighing with the standard-size weighing pan

(22 mm Ø = ~ 1" Ø):

— Slightly lift the cover of the weighing chamber and turn it

to the left or to the right

— Place the spacer (16) and the inferior draft shield (3) in

the weighing chamber

— Use forceps to position the pan support (2) and the stan-

dard-size weighing pan (1)

Connecting the Balance to Line Power

The balance is energized by a portable power supply. Make

sure that the voltage rating printed on this unit is identical to

your local line voltage rating.

lf the voltage rating specified on the power supply or the plug

design does not match the rating or Standard you use, please

contact your Sartorius dealer.

Important Note

Only use original Sartorius power supplies identified by the Sar-

torius label. Use of power supplies made by other manufactur-

ers, even if these power supplies have a registered approval

rating from a national testing laboratory, requires the consent of

a certified Sartorius technician.

Plug the cord of the power supply into the power receptacle of

the balance. Secure the connection by tightening the knurled

collar.

Now plug the power supply into a wall outlet.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Sartorius

Sartorius

Sartorius PMA.Power Series Manual de usuario

Sartorius

Sartorius G 150 D Manual de usuario

Sartorius

Sartorius Cubis MCA Series Manual de usuario

Sartorius

Sartorius ME415S Manual de usuario

Sartorius

Sartorius IS16EDE-H Manual de usuario

Sartorius

Sartorius Extend Series Manual de usuario

Sartorius

Sartorius SECURA1102-1NUS Manual de usuario

Sartorius

Sartorius secura series Guía del usuario

Sartorius

Sartorius IB 31 Manual de usuario

Sartorius

Sartorius Cubis MCA Series Manual de usuario

Sartorius

Sartorius FB Manual de usuario

Sartorius

Sartorius Signum 1 Manual de usuario

Sartorius

Sartorius Entris II Advanced Line BCA623-1S Manual de usuario

Sartorius

Sartorius PMA 35D Manual de usuario

Sartorius

Sartorius Master series Manual de usuario

Sartorius

Sartorius 1401 MP8 Manual de usuario

Sartorius

Sartorius BP 301S Manual de usuario

Sartorius

Sartorius BL310 Manual de usuario

Sartorius

Sartorius PMA.Evolution Manual de usuario

Sartorius

Sartorius Entris II BCA Advanced Series Manual de usuario

Sartorius

Sartorius IS 300 IGG-H Manual de usuario

Sartorius

Sartorius Basiclite Manual de usuario

Sartorius

Sartorius Secura Manual de usuario

Sartorius

Sartorius 1802 Guía del usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario