Salus RT310 Manual de usuario

Installation Manual

Model: RT310

Product Compliance .................................................................................................... 3

Safety Information ........................................................................................................ 3

Box Content ...................................................................................................................... 3

Introduction ...................................................................................................................... 4

Features ............................................................................................................................... 5

Installation ......................................................................................................................... 5

Button functions and keys ....................................................................................... 7

Installer Mode .................................................................................................................. 8

Operations ......................................................................................................................... 9

Other functions .............................................................................................................. 11

Factory reset ..................................................................................................................... 12

Technical info ................................................................................................................... 12

Warranty .............................................................................................................................. 13

02 RT310 Installation Manual

Contents

Product Compliance

Safety Information

This product complies with the essential requirements and other relevant provisions of the following

EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of

Conformity is available at the following internet address: www.saluslegal.com.

Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry.

Thisproductmust be installed by a competent person and inaccordancewithallthe EU and national regulations.

Always isolate the AC Mains supply before installing or working on any components that

require 230 VAC 50Hz supply.

Box content

The box includes the RT310 thermostat, 2 AA batteries a set of screws and the Quick Guide installation manual.

RT310 thermostat 2X screws and plugs

2xAA batteries Quick Guide Installation

RT310 Installation Manual 03

Introduction

A room thermostat simply switches the heating system on and off as necessary. It works by sensing the air

temperature, switching on the heating when the air temperature falls below the thermostat setting, and

switching it off once this set temperature has been reached.

Turning a room thermostat to a higher setting will not make the room heat up any faster. How quickly the room

heats up depends on the design of the heating system, for example, the size of boiler and radiators. Neither

does the setting affect how quickly the room cools down. Turning a room thermostat to a lower setting will

result in the room being controlled at a lower temperature, and saves energy.

The heating system will not work if a time switch or programmer has switched it off.

The way to set and use your room thermostat is to find the lowest temperature setting that you are comfortable

with, and then leave it alone to do its job. The best way to do this is to set the room thermostat to a low

temperature – say 18⁰C – and then turn it up by one degree each day until you are comfortable with the

temperature.

You won’t have to adjust the thermostat further. Any adjustment above this setting will waste energy and cost

you more money.

If your heating system is a boiler with radiators, there will usually be only one room thermostat to control the

whole house. But you can have different temperatures in individual rooms by installing thermostatic radiator

valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose a temperature that is reasonable

for the whole house. If you do have TRVs, you can choose a slightly higher setting to make sure that even the

coldest room is comfortable, then prevent any overheating in other rooms by adjusting the TRVs.

Room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains

or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from

working properly.

04 RT310 Installation Manual

The RT310from SALUS Controls is a stylish and accurate

digital thermostat with an easy to read Liquid Crystal Display

(LCD).

Features

• Frost protection(selectable)

• Low-Battery Warning

• Low-Battery Detection

• Modern Casing

• Sleep Mode

• User Friendly

Features

Installation

The ideal position to locate the RT310 thermostat

is about 1.5m above ﬂoor level, in a location where

the thermostat is accessible, reasonably lit and free

from extremes of temperature and draughts. Do not

mount the thermostat on an outside wall, above a

radiator or in a location where it may be subjected

to direct sunlight. The electrical connections to

the RT310 are made to the supplied industry

standard backplate. This simpliﬁes installation, as

no connections are made to the controller itself.

Connection details are shown below - no Earth

connection is required for the correct and safe

operation of the RT310, but a parking terminal is

provided to connect an Earth wire if one is present.

RT310 front Backplate

Wiring conﬁguration

123

COM NO

TERMINAL DESCRIPTION

1 (COM) Common Terminal

2 (NC) Switched Live OFF

3 (NO) Switched Live ON

Terminal description

RT310 Installation Manual 05

Wall mounting

Fit the front housing.

Press lightly

Note: You can also use a ﬂush mount housing and a German and UK wall box to mount the thermostat directly

into the wall. The standard wall box has a diameter max 60mm and depth from 41-46 mm. The cable entry on

the backplate must allow a cable with 5*1,5 mm

The DIP switches are found on the rear of your thermostat and can be used to change the span (temperature

accuracy) of your thermostat from the default +/-0.5°C to +/-0.25°C. This may cause your boiler to operate more

frequently. The DIP switches are located on the back of the thermostat. ON +/-0.25°C, OFF +/-0.5°C.

The span is the accuracy with which the thermostat operates when displaying your temperature. You can

increase the accuracy by setting the span to +/-0.25°C, meaning that your thermostat will be sensitive to a

quarter of a degree temperature change and will activate/deactivate the boiler.

DIP switch settings

+/-0.25

+/-0.5

Fix the backplate

to the wall

Align the front housing at

the top edge.

60mm

46mm

06 RT310 Installation Manual

RESET

Key Function

Turn on the LCD backlight

Turn On/Off the Frost Mode

Increase button

Decrease button

Press once to return factory settings

Press for 3 seconds all the buttons to enter Installer

Mode

There are few user controls for the RT310, making this thermostat very easy to operate. These controls are

shown below, along with a description of each of their functions. The temperature displayed on the LCD is the

current room temperature. All the LCD icons with a description are shown below.

Thermostat RT310

Thermostat RT310 LCD Icon Meaning

Thermostat is calling for heat

Thermostat is in Frost Protect Mode

Low Battery Warning Indicator

Current Temperature/Set Point Temperature

Button functions and keys

RT310 Installation Manual 07

RESET

Select increment. Press

Installer Mode

Press and hold and and keys to enter installation setting.

The first setting is temperature display resolution selection - d01. Press to enter the existing setting. The

setting will start flashing. Press or to change temperature display resolution, wait for 10 seconds to

confirm, then enter d02 (if you didn’t press to save your selection, the change will be confirmed after 10

seconds and the thermostat will return to normal mode). d02 is to set temperature offset, press or to

increase/decrease offset.

To exit Installer Mode don’t press any key for 10 seconds, or press

See the table below.

RESET

Press the three buttons

together for 3 seconds.

3 Sec 3 Sec

3 Sec

dxx Function Parameter Description Default

value

d01 Temperature display

increments

0.1°C or

0.5°C

Select the temperature display

increments

0.5°C

d02 Temperature oﬀset +/-3.0°C Calibrate your thermostat tempera-

ture

0.0°C

d03 Frost setpoint temperature 5.0°C-17.0°C Set the Frost Point temperature 5.0°C

Enter ﬁrst d01 setting. Press

Continue adjusting the d02 and d03 following the same steps as above.

Once you have ﬁnished setting up all the parameters, press to exit

to home screen, or don’t press any button for 10 seconds and it will

exit automatically.

TESTING/PAIRING

08 RT310 Installation Manual

TESTING/PAIRING

Setpoint temperature

Operations

Initial Power UP

After power up, the thermostat is reset. During system reset, all LCD icons are displayed for 2 seconds and

the keys are locked. After that, all keys are unlocked and the thermostat is initialized. Then software version is

shown. The typical reset display is shown below.

The following table shows the settings of the RT310 digital thermostat after RESET button is pressed:

Function Status after Reset

Operation Mode Normal mode

Room Temperature 22.0°C, to be renewed within 5 seconds

Setpoint Temperature 20.0°C

°C indicator On

Frost Protection indicator Off

Heat indicator Off

Low-Battery Warning indicator Off, to be renewed within 5 seconds

Output Relay Off

Reviewing Setpoint Temperature

Press or to review Setpoint temperature. The flame icon won’t be turned on.

When operating in Frost protection mode, the LCD will show frost setpoint with the Frost Protection

indicator displayed.

Press Backlight or wait 2 seconds without keys pressed to return to normal operation, room temperature will

be displayed.

TESTING/PAIRING

Actual room temperature

RT310 Installation Manual 09

TESTING/PAIRING

By changing the Setpoint temperature, you are permanently altering your temperature. You can change the

set point temperature very easily while you are reviewing the set point temperature. Press the UP or DOWN

keys repeatedly to change the temperature setting. The set point temperature will ﬂash to indicate that it can

be changed: the temperature will be changed in 0.5°C steps per key press.

The RT310 will return to Normal mode if no keys are pressed for more than 2 seconds. Once the new Setpoint

is implemented, the change is permanently overridden until a new Setpoint is set again. Setpoint temperature

cannot be changed if Frost Protection mode is enabled.

TESTING/PAIRINGTESTING/PAIRING

Actual room temperature Setpoint temperature 2 seconds timeout Actual room temperature

Frost Protection

Press FROST button to activate Frost Protection.

The Setpoint temperature is automatically set to frost setpoint to prevent pipes from freezing. If the room

temperature is lower than the frost setpoint, frost protection will be enabled. When Frost Protection is enabled,

the user should not be able to press or adjust frost Setpoint temperature, this feature being accessible only in

installationmode.Pleaserefertopage 7 on moreinformation on Installer Mode. PressFROSTbutton again

to de-activate Frost Protection.

TESTING/PAIRINGTESTING/PAIRING

Actual room temperature Frost Mode activated

TESTING/PAIRINGTESTING/PAIRING

Actual room temperature Frost Mode deactivated

Frost Protection ON Frost Protection OFF

Note: The setpoint frost temperature can be reviewed by pressing the Up button once, but can only be

changed in Installer Mode. For more information about entering Installer Mode, please refer to page 7

TESTING/PAIRING

Frost Mode activated Frost setpoint temperature

Adjusting Setpoint Temperature

10 RT310 Installation Manual

Otros manuales para RT310

Tabla de contenidos

Otros manuales de Termostato de Salus

Salus

Salus OPTIMA ZigBee Manual de usuario

Salus

Salus ERT20 Manual de servicio

Salus

Salus VS35W Manual de usuario

Salus

Salus RT 10 Manual de usuario

Salus

Salus HTRS-RF (30) Manual de usuario

Salus

Salus CT100 Manual de usuario

Salus

Salus ST921WF Manual de usuario

Salus

Salus RT500ROF Manual de usuario

Salus

Salus Thermo 091 Manual de usuario

Salus

Salus 091FLRF Manual de usuario

Salus

Salus DT300 Manual de usuario

Salus

Salus FT100 Manual de usuario

Salus

Salus DIGITAL PROGRAMMABLE THERMOSTAT Manual de usuario

Salus

Salus ST320 Manual de usuario

Salus

Salus RT100 Manual de usuario

Salus

Salus Thermo 091 Manual de usuario

Salus

Salus TS600 Manual de usuario

Salus

Salus 091FLRF Manual de usuario

Salus

Salus 091FLRF Manual de usuario

Salus

Salus RT510RF Manual de usuario

Salus

Salus ST101ZB Manual de usuario

Salus

Salus Rogers Smart Thermostat 7 Series Manual de usuario

Salus

Salus ERT30 Manual de usuario

Salus

Salus ST620VBC Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario