Ruijie RG-AP520 Series Manual de instalación y funcionamiento

RG-AP520 Series Access Point

Hardware Installation and Reference Guide V1.0

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

, , , ,

, ,

, , ,

, , are registered trademarks of Ruijie

Networks. Counterfeit is strictly prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: http://www.ruijienetworks.com/

Service Email: [email protected]

Technical Support: http://www.ruijienetworks.com/service.aspx

Technical Support Hotline: +86-4008-111-000

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or

cause data loss.

Chapter 1 Product Overview

RG-AP520 is a wireless LAN access point (AP) designed by Ruijie Networks for demanding indoor deployments. It can

serve as a Fit AP and operate in conjunction with a unified wired/wireless switch or a wireless controller; or it can serve as

a standalone Fat AP and provide wireless access for mobile clients.

Technical Specifications

Table 1-1 Technical Specifications of RG-AP520

Hardware Specifications

Radio

2.4GHz: 2 x 2MIMO

5GHz: 2 x 2MIMO

Transmission

Protocol

2.4GHz: 802.11b/g/n

5GHz: 802.11a/n/ac

Operating Bands

802.11b/g/n: 2.4 GHz to 2.4835 GHz

802.11a/n/ac: 5.15 GHz to 5.35 GHz, 5.47 GHz to 5.725 GHz, 5.725 GHz to 5.85GHz

(Depending on which country the AP is installed)

Antenna

Built-in omnidirectional, antenna gain: 3dBi

Spatial Streams

Access Rates

2.4GHz: up to 300Mbp

5GHz: up to 867Mbps

Total: up to 1.167Gbp

Modulation

OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and [email protected]/11Mbps

MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM and 256QAM

Receive Sensitivity

802.11b: -99 dBm (1 Mbps), -93 dBm (5.5 Mbps) , -90 dBm (11 Mbps)

802.11a/g: -93 dBm (6 Mbps), -85 dBm (24 Mbps), -82 dBm (36 Mbps), -77 dBm (54 Mbps)

802.11n: -92 dBm@MCS0, -74 dBm@MCS7, -92 dBm@MCS8, -73dBm@MCS15

802.11ac HT20: -90dBm (MCS0) , -65dBm (MCS8)

802.11ac HT40: -85dBm (MCS0) , -60dBm (MCS9)

802.11ac HT80: -82dBm (MCS0) , -58dBm (MCS9)

Maximum Transmit

Power

27 dBm

(Depending on the country of use, laws and regulations)

Transmit Power

Adjustment

1 dBm

Physical

Dimensions

(W x D x H)

194 mm x194 mm x 37 mm

Weight

0.2 kg

Service Ports

One 10/100/1000BASE-T Ethernet port (PoE-capable)

Management Ports

One RJ45 Console port

LED

1 LED (red, green, blue, orange, and flashing modes, breathing flashing mode for smart device

access, and the indicator can be switched off to silent mode)

Power Supply

Adapter: DC 12V (optional)

PoE: IEEE 802.3af/802.3at-compliant (compatible).

Power Consumption

Maximum: 12.95W

Temperature

Operating: -10 to 55℃(14 to 131 ℉)

Storage: -40 to 70℃(-40 to 158 ℉)

Humidity

Operating: 5% to 95% (non-condensing)

Storage: 5% to 95% (non-condensing)

Installation

Ceiling/wall mount

IP Rating

IP41

Safety Standards

GB4943

IEC 60950-1

EMC Standards

GB9254

EN301 489

EN50155

EN50121

Vibration Standards

IEC61373

Radio

China Radio Transmission Equipment Type Approval Certificate

EN300 328

EN301 893

MTBF

>400,000H

Software Functions

Security

Data encryption

WPA(TKIP), WPA2 (AES), WPA-PSK, WEP

(64 or 128 bits), and WAPI (hardware)

Frame Filtering

White list

Static blacklist

Dynamic blacklist

Rogue AP detection and countermeasure

Support

Dynamic ACL assignment

Support

RADIUS

Support

CPU Protection Policy (CPP)

Support

User isolation

Support

Network Foundation Protection Policy (NFPP)

Support

Routing

IPv4 address

Static IP address or DHCP reservation

IPv6 CAPWAP tunnel

Support

ICMPv6

Support

IPv6 address

Manual or automatic configuration

IPv6 tunnel

Manual or automatic configuration

ISATAP

Support

Multicast

Multicast to unicast conversion

Management and

Maintenance

Network management

SNMP v1/v2C/v3, Telnet, SSH, TFTP, and

FTP and Web management

Fault detection and alarm

Support

Statistics and logs

Support

FAT/FIT switching

Support

Maximum stations per AP

128 (The actual number of users depends on

environmental factors.)

The recommended number of stations per AP

Virtual AP

A maximum of 32 SSIDs

SSID hiding

Support

Configuring the authentication mode,

encryption mechanism, and VLAN attributes

for each SSID

Support

WDS (bridge mode)

Support

Remote Intelligent Perception Technology

(RIPT)

Support

Fair scheduling

Support

Intelligent identification of smart device

Support

Intelligent load balancing based on the number

of users or traffic

Support

STA control

SSID/radio-based

Bandwidth control

STA/SSID/AP-based speed control

5G band select

Support

The weight refers to the weight of host and bracket.

Product Image

The AP provides 5 ports, including 2 internal RF antenna ports, 1 Ethernet ports (PoE-capable), 1 Console port, and 1

power port for external power supply.

Figure 1-1 Top Panel of RG-AP520

LED Indicators

Fit AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

Initialization in progress

Solid green

N/A

Initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

Blinking blue

3Hz

Initialization is complete, and the AP is establishing a CAPWAP connection

with an AC.

Blinking orange

3Hz

Firmware upgrade in progress. Do not power off.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Breathing blue

16 breaths/min

Normal operation, at least one wireless client is associated with the AP.

Solid red

N/A

Warnings(defined by software)

Double blinking

red

3Hz (on and off for

2 cycles

alternately)

Locate AP.

Fat AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

Initialization in progress

Solid green

N/A

Initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

Blinking orange

3Hz

Firmware upgrade in progress. Do not power off.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Breathing blue

16 breaths/min

Normal operation, at least one wireless client is associated with the AP.

Solid red

N/A

Warnings(defined by software)

Double blinking

red

3Hz (on and off for

2 cycles

alternately)

Locate AP.

Power Sources

The AP can be powered either with a power adapter or through Power over Ethernet (PoE).

The AP requires Ruijie power adapters (If needed, you can buy them from Ruijie).

To use a PoE device, make sure it supports the IEEE 802.3af/at PoE standard.

Cooling Solution

The AP adopts fanless design.

Leave sufficient space at the surrounding of the AP when place the AP to permit airflow for proper ventilation.

Chapter 2 Preparing for Installation

To prevent device damage and bodily injury, please read carefully the safety recommendations described in

this chapter.

The recommendations do not cover all possible hazardous situations.

Installation

The AP must be installed indoors. To ensure its normal operation, the installation site must meet the following

requirements.

Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling

system.

Make sure the site is sturdy enough to support the AP and its accessories.

Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.

Do not expose the AP to high temperature, dusts, or harmful gases.

Do not install the AP in an inflammable or explosive environment.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the seaside and do not face it toward the wind from the sea.

The installation site should be free from water flooding, seepage, dripping, or condensation.

The installation site shall be selected according to network planning and features of communications equipment, and

considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.

Please follow the correct method described in the installation guide to install and remove the device.

Movement

Avoid moving the device frequently.

Turn off all power supplies and unplug all power cables before you remove the device.

EMI

Please observe local regulations and specifications when performing electrical operations. Relevant operators must

be qualified.

Please carefully check for any potential danger in the working area, for example, damp/wet ground or floor.

Find out the location of the emergency power supply switch in the room before installation. First cut off the power

supply in case of an accident.

Be sure to make a careful check before you shut down the power supply.

Do not place the device in a damp/wet location. Do not let any liquid enter the chassis

Keep the AP far away from the grounding or lightning protection devices of power equipment.

Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus

causing severe even fatal damages to human bodies and device.

Direct or indirect touch through a wet object on high voltage and power line can bring a fatal danger.

Ventilation

For proper ventilation, leave sufficient space around the AP.

Temperature and Humidity

To ensure normal operation and service life of the device, maintain appropriate temperature and humidity levels in your

equipment room. See Table 2-1. Improper room temperature and humidity can cause damages to the device.

High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage, and

sometimes may lead to change of mechanical properties of materials and corrosion of metal parts.

Low relative humidity may dry and shrink insulation sheets and cause static electricity that can damage the circuitry

inside the device.

High temperature greatly reduces reliability of the device and shortens its service life.

Table 2-1 Required Temperature and Humidity for the RG-AP520

Temperature

Relative Humidity

-10 to 55 ºC

5% to 95%

Cleanness

Dust poses a serious threat to device operation. Dust that falls onto the surface of the device can be absorbed onto metal

contact points by static electricity, resulting in poor contact. Electrostatic absorption of dust occurs more easily when the

relative humidity is low, which may shorten the service life of the device and cause communication failures. Table 2-2

shows the maximum concentration and diameter of dust allowed in the equipment room.

Table 2-2

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Ruijie

Ruijie

Ruijie HA3515-DG Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee RG-RAP6262 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP820(AR) Manual de instalación y funcionamiento

Ruijie

Ruijie RG-MAP852-SF-S Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee RG-RAP1260 Manual de instalación y funcionamiento

Ruijie

Ruijie RG-EAP602 Series Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee RG-RAP6202(G) Manual de instalación y funcionamiento

Ruijie

Ruijie RG-RAP1200 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP840-I Series Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee Series Manual de usuario

Ruijie

Ruijie Reyee RG-RAP73HD Manual de usuario

Ruijie

Ruijie RG-AP680-A Manual de instalación y funcionamiento

Ruijie

Ruijie RG-SAP825-SP Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP880-AR Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP820-I Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP220 Series Manual de usuario

Ruijie

Ruijie RG-AM5528-SF Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee RG-RAP6262 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP130(L) Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP180 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP130(W2) V2 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-AP180-I Manual de instalación y funcionamiento

Ruijie

Ruijie AP850-AR Manual de instalación y funcionamiento

Ruijie

Ruijie RG-WLAN Series Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario