Rockwell Automation Allen-Bradley 150-E Manual de usuario

User Manual Original Instructions

Elevator Panel Solution

Bulletin 150-E

2Rockwell Automation Publication 150-UM009E-EN-P - August 2021

Elevator Panel Solution User Manual

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize

themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to

be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use

or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

These labels may also be on or inside the equipment to provide specific precautions.

The following icon may appear in the text of this document.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Identifies information that is useful and can help to make a process easier to do or easier to understand.

Rockwell Automation Publication 150-UM009E-EN-P - August 2021 3

Table of Contents

About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Summary of Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

European Communities (EC) Directive Compliance . . . . . . . . . . . . . . . . . 6

EMC Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Low Voltage Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

UL/CSA Elevator Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 1

Introduction Component Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Base Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Fault Contactor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Starter Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

For 6- or 12-Lead Wye-Delta Wound Motors . . . . . . . . . . . . . . . . . . . . . 9

For 3- or 9-Lead Closed Delta-Type Motors . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2

Installation and Wiring Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Motor Branch Protection and Disconnecting Means . . . . . . . . . . . . 12

Electrical Noise Suppression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power Factor Correction Capacitors (PFCCs) . . . . . . . . . . . . . . . . . . . 12

Terminal Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Typical Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chapter 3

Programming DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Motor FLA Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Motor Overload Trip Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Input and Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 4

Troubleshooting Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Diagnostics Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Renewal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4Rockwell Automation Publication 150-UM009E-EN-P - August 2021

Table of Contents

Chapter 5

Specifications Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Approximate Dimensions and Shipping Weights . . . . . . . . . . . . . . . . . . 28

Appendix A

History of Changes Approximate Dimensions and Shipping Weights . . . . . . . . . . . . . . . . . . 29

Rockwell Automation Publication 150-UM009E-EN-P - August 2021 5

Preface

About This Publication This publication provides detailed instructions that you need to select, install,

program, and troubleshoot Bulletin 150-E Elevator Controller Panels.

Summary of Changes This publication contains the following new or updated information. This list

includes substantive updates only and is not intended to reflect all changes.

This document has also been reformatted.

Additional Resources These documents contain additional information concerning related products

from Rockwell Automation.

You can view or download publications at rok.auto/literature.

Topic Page

Added Additional Resources section 5

Added European Communities (EC) Directive Compliance 6

Update for series change; fault contactors for Series C updated to Bulletin 100-E contactor

options, replacing Bulletins 100-C and 100-D devices 8,25

Resource Description

SMC-3, SMC Flex, and SMC-50 Smart Motor Controllers Technical Data,

publication 150-TD009 Provides specifications and application profiles for the SMC™ Smart Motor Controller

product line.

IEC Contactor Specifications, publication 100-TD013 Provides specifications for IEC contactors.

Industrial Components Preventive Maintenance, Enclosures, and Contact

Ratings Specifications, publication IC-TD002 Provides a quick reference tool for Allen-Bradley industrial automation controls and

assemblies.

Safety Guidelines for the Application, Installation, and Maintenance of

Solid-state Control, publication SGI-1.1

Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides

general guidelines for the application, installation, and maintenance of solid-state control in

the form of individual devices or packaged assemblies incorporating solid-state

components.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website, rok.auto/certifications. Provides declarations of conformity, certificates, and other certification details.

6Rockwell Automation Publication 150-UM009E-EN-P - August 2021

Preface

European Communities (EC)

Directive Compliance

If this product has the CE mark, then it is approved for installation within the

European Union. It has been designed and tested to meet the following

directives.

EMC Directive

This product is tested to meet the Council Directive 2014/30/EU

Electromagnetic Compatibility (EMC) by applying the following standards, in

whole or in part, documented in a technical construction file:

EN 60947-4-2 — Product Standard

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 2014/35/EU Low Voltage. This

equipment is classified as open equipment and must be mounted in an

enclosure during operation to provide safety protection.

UL/CSA Elevator Ratings

Bulletin 150-C Soft Starters are cULus Listed (Canadian Standards per UL 508

and CSA C22.2 No. 14) as solid-state motor controllers in File E96956. They are

also cULus Listed (CAN/CSA B44.1-96) as elevator controllers in UL File E96956.

Rockwell Automation Publication 150-UM009E-EN-P - August 2021 7

Chapter 1

Introduction

This manual provides and overview of the installation, set-up, and typical

operation of the Allen-Bradley® hydraulic elevator and escalator starter. This

solid- state starter solution is designed to operate 3-phase standard squirrel

cage induction motors and can be connected to a 6- or 12-lead Wye-Delta or

standard 3- or 9-lead motors. Through the use of line or inside-the-delta

control, the solid-state solution can provide ultimate control of the motor. The

advantages of a solid-state solution include the following:

• Provides smooth motor starting.

• Reduces current surges on weak electrical systems.

• Reduces starting torque of the motor, which helps to reduce mechanical

stress on system components.

• Helps meet both local and regional electrical codes when reduced voltage

starting is a requirement.

• Eliminates voltage and current spikes associated with traditional Wye-

Delta starters.

• Maximizes the life of the motor with reduced electrical strain.

• Reduces general system maintenance requirements for improved

uptime.

Component Overview The starter is made up of two components, the base controller and a fault

contactor.

Figure 1 - Bulletin 150-E Components

Base Controller

Fault Contactor

8Rockwell Automation Publication 150-UM009E-EN-P - August 2021

Chapter 1 Introduction

Base Controller

The base controller is a standard product that uses intelligent features to

provide advanced motor control and simple diagnostics. The base controller

consists of the elements necessary to control the motor. These elements

include:

• a main micro-processor

• current sensing

• built-in adjustable overload

• solid-state power modules, and

• electro-mechanical bypass contacts.

Through the use of simple DIP switch configuration, you can configure the

controller for a variety of modes. The default configuration uses the built-in

current sensing to limit current to the motor during startup. Once up to speed,

the base controller transitions to the run mode by transitioning to internal

bypass contactors and changing the state of the auxiliary contact. The internal

bypass contactor provides decreased heating during run and removes the

SCRs from the circuit.

Fault Contactor

The fault contactor is controlled through the fault contact of the controller.

When control power is applied to the controller, the normally open fault

contact closes and applies control power to the coil of the contactor. The fault

contact opens, removing power from the fault contactor, and thus disabling

the motor during any one of the following events:

• The power is removed from the controller.

• The motor has developed a problem including overloading due to one of

the following:

- Mechanical or electrical reasons

- Ground faults or

- Motor short circuits.

• The starter has detected an internal problem such as a shorted SCR or

overtemperature condition.

Function Overview The Bulletin 150-E elevator panel provides solution to both advanced motor

control and simple diagnostics. Table 1 and Table 2 provide a brief overview of

the basic product features.

150-E Series B devices use Bulletin 100-C or 100-D contactors. Series C devices use

Bulletin 100-E contactors. See Table 20 for more information.

Table 1 - Motor Control Features

Function Description

Current Limit

Using internal current sensors, the SMC™ controller regulates the current level that is applied to

the motor over the programmed period of time. This type of motor control produces a slow start

and ensures that the current does not exceed the programmed level. This is the standard

configuration of the device and aligns well with traditional applications.

Soft Start The voltage is ramped from an initial set point to full voltage over the programmed period of

time. This type of motor control produces a smooth start in less time than the current limit

setting. However, it does not restrict the current.

Soft Stop The voltage is ramped down from full voltage and applied to the motor over a programmed

period of time. The result is a smooth stop.

Rockwell Automation Publication 150-UM009E-EN-P - August 2021 9

Chapter 1 Introduction

Starter Selection For 6- or 12-Lead Wye-Delta Wound Motors

The following table lists the catalog numbers that can be used with 6 or 12 lead

Wye-Delta motors. For proper operation, the connection should be verified

during installation. Chapter 2 includes sample connection diagrams for

inside-the-delta connected motors.

For 3- or 9-Lead Closed Delta-Type Motors

The following table lists the catalog numbers that can be used with 3- or 9-lead

closed delta type motors. For proper operation, the connection should be

verified during installation. Chapter 2 includes sample connection diagrams

for line-connected motors.

Table 2 - Diagnostic Features

Function Description

Overload

Provides protection of the motor for over current conditions. This feature offers a user-

selectable setting called the trip class, which can be used to accommodate different

applications and motor types. When the motor draws more than the nominal value of current

for a period of time, the device faults on a motor overload fault.

Overtemperature A built-in self-monitoring method for detecting a SCR overtemperature condition. If the internal

temperature exceeds a design threshold, the device faults on a SCR Overtemp fault.

Phase Reversal You can select the phase relationship of the incoming power. If this phase relationship

changes, the device faults, indicating a problem.

Phase Loss/

Open Load When any one of the incoming 3 phases are lost, the controller faults, indicating a phase loss

condition has occurred.

Phase Imbalance When enabled, detects whether a phase imbalance condition exists and fault the unit. A phase

imbalance is defined as a 65% differential between the highest and lowest phase for more than

3seconds.

Shorted SCR Each time the SMC controller initiates a start, it checks to see if the SCRs are operating

correctly. If the controller is unable to properly turn on and off any one of the SCRs, the device

faults on a Shorted SCR fault.

Table 3 - Cat. Nos. For Use with 6- or 12-Lead Wye-Delta Motors

Hp at Nominal Ratings Overload Range(1)

(1) Motor FLA must fall within the specified range to operate correctly.

Control Voltage Cat. Nos.

200V 240V 480V 575V 120V 230V

10 10 20 30 10.9…32.9 150-E32NCE-FC 150-E32NCA-FC

15 15 30 40 17…51 150-E51NCE-FC 150-E51NCA-FC

20 20 40 60 21.3…64 150-E64NCE-FC 150-E64NCA-FC

20 25 50 60 24.7…74 150-E74NCE-FC 150-E74NCA-FC

30 40 75 100 34.7…104 150-E104NCE-FC 150-E104NCA-FC

40 50 100 150 49…147 150-E147NCE-FC 150-E147NCA-FC

75 75 150 200 59…234 150-E234NCE-FC 150-E234NCA-FC

Table 4 - Cat. Nos. For Use with 6 or 12 Lead Closed Delta-Type Motors

Hp at Nominal Ratings Overload Range(1)

(1) Motor FLA must fall within the specified range to operate correctly.

Control Voltage Cat. Nos.

200V 240V 480V 575V 120V 230V

5 5 10 15 6.3…19 150-E32NCE-FC 150-E32NCA-FC

7.5 10 20 25 10…30 150-E51NCE-FC 150-E51NCA-FC

10 10 25 30 12.3…37 150-E64NCE-FC 150-E64NCA-FC

10 15 30 40 14.3…43 150-E74NCE-FC 150-E74NCA-FC

15 20 40 50 20…60 150-E104NCE-FC 150-E104NCA-FC

25 30 60 75 28.3…85 150-E147NCE-FC 150-E147NCA-FC

40 50 100 125 34…135 150-E234NCE-FC 150-E234NCA-FC

Rockwell Automation Publication 150-UM009E-EN-P - August 2021 10

Chapter 2

Installation and Wiring

Unpacking Before installation, unpack the starter panel from its packaging and perform a

complete visual inspection of the panel. Inspect all components for damage

related to shipping and handling, including the controller, wiring, and fault

contactor. Claims for damage must be made to the carrier as soon as possible

after receipt of the shipment.

Mounting The small footprint of the starter panel makes it ideal for mounting in the

same space previously occupied by legacy solid-state starters and traditional

full-voltage starters. The starter panel does not have mounting requirements

beyond the basic footprint of the panel.

The product can incorporate a small cooling fan. There are no additional

cooling requirements for the product. However, it is good practice to leave at

least 6 inches (15.24 cm) of free space above and below the unit for ideal air

flow.

Dimensions Figure 2 - Panel Dimensions for 32, 51, and 64 A Elevator Panels

Note Information

This screw is intended to secure a prepared bonding conductor (example: a bonding conductor with a

crimped-on lug) or a suitable terminal for connection of an unprepared bonding conductor (example: a

bonding conductor with a stripped wire end). This screw is not intended for a direct field wiring

connection of an unprepared bonding conductor or equipment grounding conductor.

4.56

(115.7)

5.67

(144.0)

7.01

(178.0)

6.50

(165.1)

5.00

(127.0)

4x Ø 0.220 thru

(5.6)

CAT. XXXXXXXX SER. B

T6 T4 T5

(1)

Tabla de contenidos

Otros manuales de Controladores de Rockwell Automation

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix VP Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Manual del propietario

Rockwell Automation

Rockwell Automation Allen-Bradley G Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Dialog Plus 1503D Manual de usuario

Rockwell Automation

Rockwell Automation CompactLogix series Manual de usuario

Rockwell Automation

Rockwell Automation ARMORSTART Manual del propietario

Rockwell Automation

Rockwell Automation PowerFlex 700 Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Rockwell Automation

Rockwell Automation MicroLogix 1500 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 513 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 755 Guía rápida

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Manual de usuario

Rockwell Automation

Rockwell Automation MicroLogix 1000 Manual de usuario

Rockwell Automation

Rockwell Automation 1766-L32AWA Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 7000 Manual de instrucciones

Rockwell Automation

Rockwell Automation 1763-L16AWA Manual de usuario

Rockwell Automation

Rockwell Automation Micro830 Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Rockwell Automation

Rockwell Automation SLC 500 Thermocouple Manual de usuario

Rockwell Automation

Rockwell Automation SMC FLEX Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1769 CompactLogix Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley SMC Dialog Plus Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario