Rockwell Automation Allen-Bradley 513 Manual de usuario

Four holes for 3/8" (9.5mm)

dia. mounting screws

Disconnecting device

operating handle in

“OFF” position

Coupling latch

Locking attachment

(Shown in the locked position)

Hole for lock

Nut and lock washer

(Locking attachment removed for clarity)

T-Bolt

Installation Instructions

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

When it is desired to remove or replace the enclosure cover, the following recommended procedures should be observed.

Removing the enclosure cover:

Swing back locking attachment on the V-Band. Loosen nut on the T-Bolt of the V-Band to permit the coupling latch to be disengaged from the head of

the T-Bolt. Pull out coupling latch from the head of the T-Bolt. Spread V-Band and place over the enclosure base, thereby freeing the cover for removal.

Remove enclosure cover and place on a at stable surface with the opening up.

CAUTION: Avoid any damage to ange surfaces as this could aect enclosure’s suitability for use in hazardous atmospheres.

Replace the enclosure cover:

Before replacing enclosure cover, clean base and cover anges with a soft cloth. Looking at the cover front in the upright position (nameplate in

readable position), place operating handle in the downward or “OFF” position. Leave in “OFF” position for maximum safety. Align ribs inside the cover

with positioning channels on the mounting plates.

CAUTION: The upright position of the cover and base plus proper positioning channel alignment are very important. Failure to observe these directions may cause

over jamming and equipment damage.

Slide cover toward base until the positioning pins in the base nearly enter the holes in the cover. At this point, when a disconnecting means is provided,

the external operating handle should be lifted slightly so that the circuit breaker operating slide mechanism becomes engaged with the roller. Continue

sliding cover toward base until the base and cover anges meet. Install V-Band over the anged joint and slide the T-Bolt into the coupling latch with

the tightening nut to the right.

CAUTION: Tighten the 3/8" (9.5) x 16 T-Bolt nut securely to provide proper enclosure sealing. NOTE: As a minimum, the helical spring lock washer beneath the nut

must be fully compressed (65 lb-in/7.3 N•m). The maximum torque applied to the nut should not exceed 125 lb-in/14.1 N•m.

Press locking attachment over the bolt and nut, and insert lock (when used) into the hole in the locking attachment.

WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Keep free from contaminants.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or

damage, no attempts at repair should be made. The product should be returned to the manufacturer for repair. Do not dismantle the product.

4 6

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

3/4" (19 mm) - 14 N.P.T.

(Drain location)

3/4" (19 mm) - 14 N.P.T.

(Breather location)

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

Publication 513-IN006F-EN-P - October 2017 40050-226-01 DIR 40050-226 (Version 06)

Wiring:

A number of openings are provided in the base for power and control wiring as well as for accessories. See illustrations above. Location and quantity

of the various accessories will determine the openings available for wiring.

Openings 1 and 4 are supplied with 1-1/2" (38 mm) pipe plugs while openings 2 and 5 are supplied with 3/4" (19 mm) pipe plugs.

Openings 3 and 6 are shipped with red plastic cap plugs. These openings are generally used for power and control wiring. If not used they must be

closed with 1-1/2" (38 mm) pipe plugs.

Wiring of electrical equipment or any other accessory is to be done in accordance with instructions furnished with the equipment and applicable

codes and laws.

To comply with the NEC, CEC, IEC and ATEX Directives and to prevent the passage of gasses, vapors or ames from one portion of the electrical

installation to another, conduit openings must be sealed with an appropriate sealing tting. For use with metallic conduit only.

Mounting of a Unilock enclosure:

Mounting straps are provided on the rear of the enclosure for ease of mounting. The Unilock enclosure may be mounted to any solid surface capable

of supporting it’s weight by using 3/8" (9.5 mm) diameter screws or bolts.

Exterior dimensions of the Unilock enclosure are shown on sheet 3.

Front View Back View

Dimensions:

15-3/8"

(390.5 mm)

2-7/16"

(61.9 mm)

3/8"

(9.5 mm)

2-5/8"

(66.7 mm)

5-1/4"

(133.4 mm)

13-1/4"

(336.6 mm)

7-1/4"

(184.2 mm)

Mounting

5-7/8"

(149.2 mm)

11-3/4"

(298.4 mm)

Mounting

Four 3/8" (9.5 mm)

Mounting screws

6-7/16"

(163.5 mm)

8-1/16"

(204.8 mm)

3-5/8"

(92.1 mm)

Publication 513-IN006F-EN-P - October 2017 40050-226-01 DIR 40050-226 (Version 06)

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

40050-226-01

DIR 40050-226 (Version 06)

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 513-IN006F-EN-P - October 2017

Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Rockwell Automation

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 23PFC Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 70 Manual de usuario

Rockwell Automation

Rockwell Automation GV3000/SE 230 Manual de instalación y operación

Rockwell Automation

Rockwell Automation 1785 PLC-5 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Manual de usuario

Rockwell Automation

Rockwell Automation MPMA Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Manual

Rockwell Automation

Rockwell Automation Allen-Bradley CompactLogix 1769-L32E Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Manual de usuario

Rockwell Automation

Rockwell Automation SmartGuard 600 Manual de operación

Rockwell Automation

Rockwell Automation Allen-Bradley Dialog Plus 1503D Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Manual del propietario

Rockwell Automation

Rockwell Automation Allen-Bradley Logix5000 Manual del propietario

Rockwell Automation

Rockwell Automation 1756-L1 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 525 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-Flex 150 Manual de usuario

Rockwell Automation

Rockwell Automation 1336 PLUS Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L30ER Manual de usuario

Rockwell Automation

Rockwell Automation ARMORSTART 280D Manual de usuario

Rockwell Automation

Rockwell Automation MicroLogix 1000 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley DriveLogix 5730 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario