Reed Instruments R9510 Manual de usuario

Digital

Refractometer

Instruction

Manual

R9510

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Table of Contents

Introduction ................................................................................................ 2

Product Quality .......................................................................................... 3

Safety ......................................................................................................... 3

Features ..................................................................................................... 3

Includes ..................................................................................................... 4

Specications ............................................................................................ 4

Instrument Description ............................................................................... 5

Display Description .................................................................................... 5

Operating Instructions ............................................................................6-7

Power ON/OFF...................................................................................... 6

Zero Calibration .................................................................................... 6

Measuring Procedure .........................................................................6-7

Auto Power Off ..................................................................................... 7

Sample Well Maintenance .................................................................... 7

Charging the Battery .................................................................................. 7

Error Codes ................................................................................................ 8

Applications ............................................................................................... 8

Accessories and Replacement Parts ......................................................... 8

Product Care .............................................................................................. 8

Product Warranty ....................................................................................... 9

Product Disposal and Recycling ................................................................ 9

Product Support ........................................................................................ 9

Introduction

Thank you for purchasing your REED R9510 Digital Refractometer. Please

read the following instructions carefully before using your instrument. By

following the steps outlined in this manual your meter will provide years of

reliable service.

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Product Quality

This product has been manufactured in an ISO9001 facility and has been

calibrated during the manufacturing process to meet stated product

specications. If a certicate of calibration is required please contact the

nearest authorized REED distributor or authorized Service Center. Please

note an additional fee for this service will apply.

Safety

• Never attempt to repair or modify your instrument. Dismantling

your product may cause damage that will not be covered under the

manufacturer's warranty. Servicing should only be provided by an

authorized service center.

• When the unit needs to be washed, use water at a temperature not

exceeding 86°F (30°C).

• The prism must be cleaned thoroughly with a soft, clean damp cloth

after each use—failure to do so will result in inaccurate readings and

possible long term damage.

• Do not

drop or use excessive force as it may result in damage to the meter.

• Do not scratch the prism surface.

• Do not leave the instrument in a location exposed to direct sunlight or

near a heat source for an extended period of time.

• Do not attempt to measure corrosive chemicals as it will damage

theinstrument.

Features

• 0 to 55% Brix measurement range with 0.1% resolution

• Ergonomically designed for one-handed operation

• Dual LCD simultaneously displays % Brix and temperature

• Sapphire prism with abrasion and corrosion-resistant coating

• Automatic Temperature Compensation (ATC)

• Built-in Zero calibration

• Rechargeable battery

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Included

• Digital Refractometer

• USB Cable

• Cleaning cloth

• Solution/Sample applicator

Specifications

Measurement Range: Brix: 0 to 55%

Temperature:

50 to 104°F (10 to 40°C)

Resolution: Brix: 0.1%

Temperature: 1°F (1°C)

Accuracy: Brix: ±0.2%

Temperature: ±1°F (1°C)

Temperature Compensation Range:

50 to 104°F (10 to 40°C)

Sample Volume: 0.3mL

Measurement Time: 3 seconds

Auto Shut-off: 2 minutes

Power Supply: 750mAh rechargeable Li-ion battery

Battery Life: 40 hours

Charge Time: 3.5 hours

Product Certications: CE, IP54

Dimensions: 5.5 x 2.2 x 1.38" (140 x 55 x 35mm)

Weight: 0.19lbs (84g)

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Instrument Description

1. LCD Display

2. Power Button

3. ZERO Button

4. Protective Cover

5. START Button

6. Sample Well

7. USB Interface

Display Description

1. Battery Status Indicator

2. Temperature Measurement Reading

3. % Brix Measurement Mode Indicator

4. % Brix Measurement Reading

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Operating Instructions

Power ON/OFF

Turn the meter ON or OFF by holding down the Power button for

approximately 2seconds.

Zero Calibration

Before each use, perform a Zero calibration. The temperature of

the distilled or tap water used for zero calibration should be the

same as the ambient temperature. If the temperature is different,

allow the water to adjust to the ambient temperature before

performing a zero calibration.

Be sure that the measuring surface and well are clean as outlined under

the "Sample Well Maintenance" section.

1. Apply distilled water (minimum of 0.3ml) to the sample well as

shown below.

2. When ready, close the protective cover and press the ZERO button

twice to enter zero calibration mode.

3. A series of dashes ( – – – ) will appear on the display followed by

0.0%Brix which conrms that the zero calibration was successful.

4. The R9510 is now ready to use.

Measuring Procedure

1. Inspect the sample well to be sure that there is no residue remaining

from a previous measurement/calibration. If the sample well does

not appear to be clean, do not take a measurement and refer to the

"Sample Well Maintenance" section for details.

continued...

about 2mm

water about 0.3ml

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

2. Apply the measuring liquid to the sample well (minimum of 0.3ml).

Note: For accurate measurements, it is recommended to completely cover

the sample well surface.

The temperature of the measuring liquid should be the same as the

ambient temperature. If the temperature is different, allow the liquid

to adjust to the ambient temperature before taking a measurement.

3. When ready, close the protective cover and press the START button

to take a measurement.

4. A series of dashes ( – – – ) will appear on the display followed by the

measured Brix value

(%)

and the temperature value of the liquid sample.

5. Remove the liquid sample by wiping it off with a tissue properly

clean the sample well as highlighted in the "Sample Well

Maintenance" section.

Auto Power Off

To preserve battery life, the meter is programmed to turn off after

approximately 2 minutes of inactivity.

Sample Well Maintenance

Cleaning of the sample well should be performed immediately after each

sample reading. Never immerse the meter in any liquid. When the sample

well has been completely cleaned no residue should be present.

To properly clean the sample well use Isopropyl Alcohol followed by a

distilled water rinse and then thoroughly dry with the included cleaning

cloth, a residue free cloth or delicate task wipes.

Charging the Battery

1. Connect the R9510 via the included cable to a USB port on your PC

or into a wall outlet using a USB Power Adapter (not included) to

charge the Li-ion battery.

Note: The meter must remain powered off to properly charge via the

USBport on your PC.

2. Charge the meter until the battery indicator appears full and remove

the charging cable when done.

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Error Codes

Code Description

ERR1 Re-calibrate with distilled water.

ERR2 Measuring liquid exceeds the % Brix measuring range.

ERR3 No/inadequate measuring liquid present. Add measuring liquid.

ERR4 Incorrect measuring liquid used.

Applications

• Fruit and citrus industry

• Juice factories

• Vineyards

• Food preparation

• Consumer use

• Agriculture

Accessories and Replacement Parts

•CA-52A Soft Carrying Case

Don't see your part listed here? For a complete list of all accessories and

replacement parts visit your product page on www.REEDInstruments.com.

Product Care

To keep your instrument in good working order we recommend the following:

• Store your product in a clean, dry place.

• Charge the battery as needed.

• Clean your product with biodegradable cleaner. Do not spray the cleaner

directly on the instrument. Use on external parts only.

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Product Warranty

REED Instruments guarantees this instrument to be free of defects in

material or workmanship for a period of one (1) year from date of shipment.

During the warranty period, REED Instruments will repair or replace, at no

charge, products or parts of a product that proves to be defective because

of improper material or workmanship, under normal use and maintenance.

REED Instruments total liability is limited to repair or replacement of the

product. REED Instruments shall not be liable for damages to goods,

property, or persons due to improper use or through attempts to utilize the

instrument under conditions which exceed the designed capabilities. In

order to begin the warranty service process, please contact us by phone

at 1-877-849-2127 or by email at [email protected] to discuss

the claim and determine the appropriate steps to process the warranty.

Product Disposal and Recycling

Please follow local laws and regulations when disposing or recycling your

instrument. Your product contains electronic components and must be

disposed of separately from standard waste products.

Product Support

If you have any questions on your product, please contact your authorized

REED distributor or REED Instruments Customer Service by phone at

1-877-849-2127 or by email at [email protected].

Please visit www.REEDInstruments.com for the most

up-to-date manuals, datasheets, product guides and software.

Product specifications subject to change without notice.

this manual is strictly prohibited without prior written permission

from REED Instruments.

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

www.REEDInstruments.com

TEST & MEASURE

WITH CONFIDENCE

CHECK OUT OUR LATEST PRODUCTS!

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Tabla de contenidos

Otros manuales de Instrumento de medición de Reed Instruments

Reed Instruments

Reed Instruments SD-4023 Manual de usuario

Reed Instruments

Reed Instruments R7050 Manual de usuario

Reed Instruments

Reed Instruments R5055 Manual de usuario

Reed Instruments

Reed Instruments R6000 Manual de usuario

Reed Instruments

Reed Instruments R9260 Manual de usuario

Reed Instruments

Reed Instruments R7920 Manual de usuario

Reed Instruments

Reed Instruments R8080 Manual de usuario

Reed Instruments

Reed Instruments R5065 Manual de usuario

Reed Instruments

Reed Instruments R7700 Manual de usuario

Reed Instruments

Reed Instruments R8140 Manual de usuario

Reed Instruments

Reed Instruments R6200 Manual de usuario

Reed Instruments

Reed Instruments R8085 Manual de usuario

Reed Instruments

Reed Instruments R3525 Manual de usuario

Reed Instruments

Reed Instruments SMART Series Manual de usuario

Reed Instruments

Reed Instruments R9400 Manual de usuario

Reed Instruments

Reed Instruments SMART Series Manual de usuario

Reed Instruments

Reed Instruments HT-6510A Manual de usuario

Reed Instruments

Reed Instruments LM-81LX Manual de usuario

Reed Instruments

Reed Instruments R9930 Manual de usuario

Reed Instruments

Reed Instruments R8050 Manual de usuario

Reed Instruments

Reed Instruments R6210 Manual de usuario

Reed Instruments

Reed Instruments R7900 Manual de usuario

Reed Instruments

Reed Instruments Smart Series Manual de usuario

Reed Instruments

Reed Instruments R3530 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario