Reed Instruments HT-6510A Manual de usuario

Scale

Durometer

Instruction

Manual

HT-6510A

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Table of Contents

Introduction ................................................................................................ 2

Product Quality........................................................................................... 3

Safety ......................................................................................................... 3

Features...................................................................................................... 3

Included...................................................................................................... 3

Specications............................................................................................. 4

Instrument Description............................................................................... 5

Operating Instructions.............................................................................6-8

Power ON/OFF ...................................................................................... 6

Measuring Procedure............................................................................. 6

Maximum Measurement Mode .............................................................. 7

Average Measurement Mode..............................................................7-8

Auto Power Off ...................................................................................... 8

Zero Calibration.......................................................................................... 8

Single Point Calibration.......................................................................... 8

Battery Replacement.................................................................................. 9

Accessories and Replacement Parts ......................................................... 9

Product Care .............................................................................................. 9

Product Warranty ....................................................................................... 9

Product Disposal and Recycling .............................................................. 10

Product Support....................................................................................... 10

Introduction

Thank you for purchasing your REED HT-6510A Durometer. Please read

the following instructions carefully before using your instrument.

By following the steps outlined in this manual your meter will provide

years of reliable service.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Product Quality

This product has been manufactured in an ISO9001 facility and has been

calibrated during the manufacturing process to meet the stated product

specications. If a certicate of calibration is required please contact the

nearest authorized REED distributor or authorized Service Center. Please

note an additional fee for this service will apply.

Safety

Never attempt to repair or modify your instrument. Dismantling your

product, other than for the purpose of replacing batteries, may cause

damage that will not be covered under the manufacturer's warranty.

Servicing should only be provided by an authorized service center.

Features

• Shore "A" hardness tester designed to measure hardness of rubber,

elastomers, natural rubber products, neoprene, polyester, resin, leather

and soft PVC

• Meets DIN 53505, ASTM D2240, ISO 7619 and JISK 7215

• 4-digit, LCD display

• Pocket-sized model with integrated probe

• Maximum and Average functions

• Zero adjustment button

• Low battery indicator and auto shut off

Included

• Wrist Strap

• Test Block

• Batteries

• Hard Carrying Case

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Specifications

Measuring Range: 10 to 90HA

Deviation: ±1HA

Resolution: 0.1HA

Sampling Time: 1 second

Display: 4-digit, LCD

Zero Button: Yes

Max and Average

Functions: Yes

Power Supply: 2 x AAA Batteries

Low Battery Indicator: Yes

Product Certications: CE

Operating Temperature: 32 to 104°F (0 to 40°C)

Storage Temperature: -4 to 140°F (-20 to 60°C)

Operating Humidity

Range: 20 to 90%

Dimensions: 6.4 x 2.6 x 1.5" (162 x 65 x 38mm)

Weight: 6.1oz (173g)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Instrument Description

CAL

ZERO

MAX N

AVE

HT-6510A

1. Battery Cover

2. Zero Button

3. Max Hold Button

4. LCD Display

5. Average Measaurement Button

6. POWER Button

7. Presser Foot

8. Indenter

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Operating Instructions

Power ON/OFF

Turn the meter on by pressing the button. To turn the meter off, press

and hold the button for approx. 2 seconds and release when "OFF"

appears on the display.

Measuring Procedure

The material under test should be a minimum of 6mm (0.25"). The test

area should allow measurements to be taken at least 12mm from any

edge. The test area may be layered with multiple pieces to achieve the

necessary thickness requirements, however the measurements taken

may not be as accurate as those taken on solid test areas, due each

layer not being in complete contact.

1. When rst powered on, the meter should display "0.0". If any other

value appears on the display, perform a zero calibration (see Zero

Calibration section for details).

2. To check accuracy, simply insert the indenter into the hole of the

calibrated test block.

3. Apply enough force to make enough contact between the top

surface of the test block and the presser foot.

4. The reading should match the test block.

5. If inaccurate, perform a single point calibration (see Single Point

Calibration section for details).

6. When ready to use, simply hold the durometer vertically with the

point of the indenter at least 12mm from any edge.

7. Place the presser foot onto the test piece while keeping the foot

parallel to the surface.

8. Apply enough force to ensure proper contact between the presser

foot and the test piece.

9. Keep in place and Hold for approx. 2 seconds.

10. The LCD will display the measured value and will hold this value until

the presser foot is removed from the test piece.

11. Repeat steps 6 through 10 for each measurement.

continued...

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Maximum Measurement Mode

1. Press the MAX button to enter the maximum value mode.

2. The Max Indicator will appear on the display.

3. Hold the durometer vertically with the point of the indenter at least

12mm from any edge.

4. Place the presser foot onto the test piece while keeping the foot

parallel to the surface.

5. Apply enough force to ensure proper contact between the presser

foot and the test piece.

6. Keep in place and Hold for approx. 2 seconds.

7. The LCD will display the measured maximum value and will hold

this value.

8. To take the next maximum value, press the ZERO button to clear

the reading.

9. Repeat steps 3 through 8 for each maximum value measurement.

10. Press the MAX button to exit maximum measurement mode and

resume normal operation.

Average Measurement Mode

The average value is calculated using the number of test measurements

the user selects which can range from 1 to 9.

1. To set the amount of test measurements required during a test

session, hold and release the button to enter the average

measurement mode.

2. The display will indicate "N" conrming it is now in average

measurement mode as well as the number of set test measurements.

3. Press the button again to scroll through the required number of

test measurements ranging from 1 to 9.

4. Press the ZERO button to conrm the selected number of

test measurements.

5. Press the MAX button to begin.

6. Hold the durometer vertically with the point of the indenter at least

12mm from any edge.

continued...

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

7. Place the presser foot onto the test piece while keeping the foot

parallel to the surface.

8. Apply enough force to ensure proper contact between the presser

foot and the test piece.

9. Keep in place and Hold for approx. 2 seconds.

10. The LCD will display the measured maximum value and will hold

this value.

11. Press the ZERO button to take the next test measurement.

12. Follow steps 6 through 11 until the selected number of test

measurements have been reached.

13. When completed, the meter will emit 2 beeps and automatically

display the average measurement value of the test session.

Auto Power Off

To preserve battery life, the meter is programmed to turn itself off after

10 minutes of inactivity.

Zero Calibration

Press the ZERO button to perform a zero calibration when required.

Single Point Calibration

1. Place the indenter onto a at test piece of glass.

2. Apply enough force to make rm contact between the glass and the

presser foot.

3. The readings on the display should be between 99.7 and 101.

4. If the reading is not within the above range, hold the button until

"CAL" appears on the display while continuing to keep pressure

against the glass.

5. When the reading has stabilized, press the button to display "0.0"

which conrms that calibration is complete.

6. Repeat steps 1 through 3 to conrm that the reading is now

within range.

7. Repeat single point calibration if reading is still out of range.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Battery Replacement

1. When the low battery symbol appears on the display, the

batteries need to be replaced.

2. Remove the battery cover on the back and insert 2 x AAA batteries.

Accessories and Replacement Parts

•R8888 Medium Hard Carrying Case

Don't see your part listed here? For a complete list of all accessories and

replacement parts visit your product page on www.reedinstruments.com.

Product Care

To keep your instrument in good working order we recommend the following:

• Store your product in a clean, dry place.

• Change the battery as needed.

• If your instrument isn't being used for a period of one month or longer

please remove the battery.

• Clean your product and accessories with biodegradable cleaner. Do not

spray the cleaner directly on the instrument. Use on external parts only.

Product Warranty

REED Instruments guarantees this instrument to be free of defects in

material or workmanship for a period of one (1) year from date of shipment.

During the warranty period, REED Instruments will repair or replace, at no

charge, products or parts of a product that proves to be defective because

of improper material or workmanship, under normal use and maintenance.

REED Instruments total liability is limited to repair or replacement of the

product. REED Instruments shall not be liable for damages to goods,

property, or persons due to improper use or through attempts to utilize the

instrument under conditions which exceed the designed capabilities. In

order to begin the warranty service process, please contact us by phone at

1-877-849-2127 or by email at [email protected] to discuss the

claim and determine the appropriate steps to process the warranty.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Product Disposal and Recycling

Please follow local laws and regulations when disposing or recycling your

instrument. Your product contains electronic components and must be

disposed of separately from standard waste products.

Product Support

If you have any questions on your product, please contact your authorized

REED distributor or REED Instruments Customer Service by phone at

1-877-849-2127 or by email at [email protected].

Please visit www.REEDINSTRUMENTS.com for the most

up-to-date manuals, datasheets, product guides and software.

Product specifications subject to change without notice.

this manual is strictly prohibited without prior written permission

from REED Instruments.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Reed Instruments

Reed Instruments

Reed Instruments SD-4023 Manual de usuario

Reed Instruments

Reed Instruments R9260 Manual de usuario

Reed Instruments

Reed Instruments R9930 Manual de usuario

Reed Instruments

Reed Instruments R3000SD Manual de usuario

Reed Instruments

Reed Instruments R3530 Manual de usuario

Reed Instruments

Reed Instruments R7050 Manual de usuario

Reed Instruments

Reed Instruments R6013 Manual de usuario

Reed Instruments

Reed Instruments R8070SD Manual de usuario

Reed Instruments

Reed Instruments R8130 Manual de usuario

Reed Instruments

Reed Instruments R6200 Manual de usuario

Reed Instruments

Reed Instruments Smart Series Manual de usuario

Reed Instruments

Reed Instruments R4700SD Manual de usuario

Reed Instruments

Reed Instruments R6210 Manual de usuario

Reed Instruments

Reed Instruments R9910SD Manual de usuario

Reed Instruments

Reed Instruments SMART Series Manual de usuario

Reed Instruments

Reed Instruments Smart Series Manual de usuario

Reed Instruments

Reed Instruments R3500 Manual de usuario

Reed Instruments

Reed Instruments LM-81AM Manual de usuario

Reed Instruments

Reed Instruments R8080 Manual de usuario

Reed Instruments

Reed Instruments LM-81HT Manual de usuario

Reed Instruments

Reed Instruments R2310 Manual de usuario

Reed Instruments

Reed Instruments R7900 Manual de usuario

Reed Instruments

Reed Instruments R7000SD Manual de usuario

Reed Instruments

Reed Instruments R5020 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario