ProLights RA3000Profile Manual de usuario

USER MANUAL

MANUALE UTENTE

RA3000PROFILE

LED MOVING PROFILE

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-04/18

RA3000PROFILE

Packing content • RA3000PROFILE

• Power cable

• Mount bracket

• User manual

TABLE OF CONTENTS Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Linking

3. 5 DMX addressing conguration

3. 6 DMX mode conguration

3. 7 DMX addressing

3. 8 Wireless settings

3. 9 Ethernet

3. 10 Movement

3. 11 Screen

3. 12 Fixture settings

3. 13 Auto and manual test

3. 14 Reset of the function

3. 15 Adjust

3. 16 Informaion of the device

3. 17 Connection of the DMX line

3. 18 Construction of the DMX termination

3. 19 DMX control

3. 20 Color - Gobos wheel

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

RA3000PROFILE

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope.When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

RA3000PROFILE

- 1 - INTRODUCTION

1.1 DESCRIPTION

RA3000PROFILE combines solid-state technology in every single detail and it has been specically engi-

neered to be not only a high quality bright light but also silent. RA3000PROFILE is able to provide a real

25’000 lumen output with unprecedented beam evenness.

The 6000KLED engine has been custom designed to make the RA3000PROFILE hit a CRI of 90, TLCI of 92,

high R9 and TM30 making all skin tones and colours come to lifeon stage or in front of a camera.

The RA3000PROFILE’s CMY system delivers beautiful pastels, stunning saturated colours, powerful prima-

ries, one colour wheel provides split colours, and linear CTO allows the RA3000PROFILE to blend in with

traditional sources.

Packed with a full feature set, composed of a gobo wheel, animation wheel, iris, prism and dual linear

frost.

High-precision 4 blade shuttering system can be over-layed to provide endless combinations. The 19

element optics of the RA3000PROFILE are precision engineered for a perfect zoom, ideal edges and

maximum eciency.

The RA3000PROFILE is silent, bright, exible and precise.

FEATURES

• 1000W LED engine with 6000K CT featuring high CRI, TLCI, R9 and TM30

• 25’000 lumen xture output with at-eld projection

• Silent

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 1000W white LED

• CT: 6000K

• CRI: >90

• R9: 75

• Luminous ux: 25’000lm

• Lux: (50°) 1830 lux (6°) 83500lux @5m

• Source life expectancy: >50.000 h

• Other: TLCI: 92; TM30-15RF:88; TM30RG:99

OPTICS

• Zoom: 6-50° motorised linear zoom

• Lens diameter: 180mm

COLOUR SYSTEM

• Colour mixing: linear CMY

• CTC: linear CTO correction 3000~6000K

• Colour wheel: 6 dichroic lters + open

DYNAMIC EFFECTS

• Shutter system: 4 single blades: +/- 35°, complete system: +/- 45°

• Animation wheel: animation wheel with CW and CCW rotation

• Rotating gobos: 6 rotating gobos + open, interchangeable, indexing

• Gobo size: Outer diameter: 31,9mm, Gobo diameter: 27mm

• Circular prism: 4f with bi-directional rotation, indexing

RA3000PROFILE

• Frost: Dual frost lter system, 1° soft-edge frost gobo, 5° frost wash, with linear 0-100% frost lter

• Iris: 5-100% motorised linear iris

BODY

• Pan angle: 540°

• Tilt angle: 270°

• Pan/Tilt resolution: 8/16 bit

• Feedback: automatic repositioning after accidental movement

• Body: Flame-retardant PC

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, Art-Net,W-DMX

• DMX channels: 38-39-40-41channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

• Display: black TFT high resolution display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Strobe / shutter: 0-30 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 1288W

• Power consumption (at 120V): 1371W

• Power factor: (120W)1.0 - (230W) 0.97

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Suspension and xing: Fast quick lock Omega bracket

• Pan / tilt lock: pan / tilt locking for transportation and maintenance

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Data connection: RJ45 IN/OUT

• Power connection: Neutrik powerCON IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 534x914x402mm

• Weight: 57kg

RA3000PROFILE

510mm

20,07in

914mm

35,98in

534mm

21,02in

402mm

15,82in

Illuminance at a Distance

6° - 50°

Lux Center Beam Angle: 6° - 50°Beam Width

10m

231944/5083lx

83500/1830lx

42602/934lx

20875/458lx

0.309/2.73m

0.515/4.55m

0.721/6.37m

1.03/9.10m

Photometric data

Technical drawing

Fig.1

RA3000PROFILE

7910

8911

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. MOVING HEAD

2. ROTARY ARM

3. TILT Mechanism Lock and Release

4. PAN Mechanism Lock and Release

5. HANDLE

6. CONTROL PANEL with TFT display

and 5 button used to access

the control panel functions and

manage them.

7. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

8. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

9. EtherCON CONNECTORS IN / OUT

signal.

10. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

11. DMX OUT ( 3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

12. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

13. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

View A

View B

Fig.2

RA3000PROFILE

- 2 - INSTALLATION

2.1 MOUNTING

The RA3000PROFILE may be set up on a solid and even surface. By means of the xing facilities of the

baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For

xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into

the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure

that the unit is rmly xed to avoid vibration and slipping while operating.The mounting place must be of

sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the xture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

CLAMP

OMEGA

RA3000PROFILE

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the RA3000PROFILE is ready for operation. To

switch o, disconnect the mains plug from the socket. For a more convenient operation it is recommend-

ed to connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The control panel of RA3000PROFILE has a display and 5 buttons for the complete programming and

management of the projector menu (g.4).

Fig.4 - Functions of the buttons and display icons

UP DOWN LEFT RIGHT ENTER

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Return to the top

level

Commute from

units, tens, hundred

in the menu

Conrms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de DJ de ProLights

ProLights

ProLights SUNRISE2 Manual de usuario

ProLights

ProLights 6 BEAM Manual de usuario

ProLights

ProLights Eclipse FC Manual de usuario

ProLights

ProLights 6BEAMQ Manual de usuario

ProLights

ProLights JETSPOT-3 Manual de usuario

ProLights

ProLights Z8STRIP Manual de usuario

ProLights

ProLights ARCLED7307HD Manual de usuario

ProLights

ProLights TRIBE LUMIPIX12UT Manual de usuario

ProLights

ProLights MINIECLFRFC Manual de usuario

ProLights

ProLights SMARTOWER Manual de usuario

ProLights

ProLights VORTEX VXBUBBLE Manual de usuario

ProLights

ProLights PANORAMAIPWBX Manual de usuario

ProLights

ProLights BEAMROLL8Q Manual de usuario

ProLights

ProLights LUMIPAR12UQPRO Manual de usuario

ProLights

ProLights UVPANEL18 Manual de usuario

ProLights

ProLights SmartBat PlusG2 Manual de usuario

ProLights

ProLights EclProfile CT+ Manual de usuario

ProLights

ProLights LASERCOMBY Manual de usuario

ProLights

ProLights BATPAR180 Manual de usuario

ProLights

ProLights SMARTTUBE32 Manual de usuario

ProLights

ProLights ASTROBEAM Manual de usuario

ProLights

ProLights Tribe LUMIPIX12UQPRO Manual de usuario

ProLights

ProLights MOSAICOXL Manual de usuario

ProLights

ProLights ARCLED7314HD Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario