ProLights SMARTOWER Manual de usuario
USER MANUAL
MANUALE UTENTE
SMARTOWER
SMARTOWERPACK
LED BATTERY LIGHTING
EN - IT
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV. 01-05/19
1
SMARTOWER - SMARTOWERPACK
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specifications
1. 3 SMARTOWERPACK (optional)
1. 4 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Recharge Process
3. 4 Menu structure
3. 5 DMX configuration
3. 6 DMX mode
3. 7 Display settings
3. 8 WIFI function
3. 9 Controller IR
3. 10 Fixture information
3. 11 Presents
3. 12 Auto
3. 13 Pattern
3. 14 Manual mode
3. 15 DMX Control
Battery Guide
2
2
3
3
5
6
7
8
8
8
9
10
10
11
11
12
13
13
13
13
13
14
17
Packing content
SMARTOWER:
• SMARTOWER
• M10 ring for security
cable
• Single charger
• IR controller
• User manual
SMARTOWERPACK:
• 6 pz SMARTOWER
• Flight case with integrated battery
charger kit
• IR controller
• PowerCON power cable
• User manual
SMARTOWER - SMARTOWERPACK
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage. Leave servicing to skilled personnel only. Never
make any modifications on the unit not described in this instruction manual, otherwise you will risk an
electric shock.
• Connection must be made to a power supply system fitted with efficient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualified electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the fixture under the following conditions:
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 40°C.
• Make certain that no inflammable liquids, water or metal objects enter the fixture.
• Do not dismantle or modify the fixture.
• All work must always be carried out by qualified technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation definitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way different to the one described in this manual, it may suffer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
• Always additionally secure the projector with the safety rope.When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
• Install the fixture in a well ventilated place.
• Keep any inflammable material at a safe distance from the fixture.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their effectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot. After power off, please
cool down over 15 minutes.
• This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
• We decline any liability deriving from improper use of the product.
3
SMARTOWER - SMARTOWERPACK
- 1 - INTRODUCTION
1.1 DESCRIPTION
SMARTOWER is a new concept of outdoor portable pixel and decor luminaire, featuring a full cable-free
operation and delivering a multitude of visual effects projecting a full 360°. SMARTOWER consists of a
vertical tubular housing with pixel battens on 4 sides delivering both colourful accent lighting as well
as eye-catching visual effects through the many built-in pixel macros which can be easily individually
customised. The unit is waterproof and equipped with on-board Wireless DMX and can be used anywhere
from corporate events and weddings right through to showrooms.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
• Light source: 360° projection with 4 pcs strips of 60x0.2W RGB/FC LEDs working together
• Source: 4x60x0.2W RGB/FC LED
COLOUR SYSTEM
• Colour mixing: RGB/FC
• CTC: CTC control through independent DMX channel
• White presets: linear change from 2600K to 10000K
• Colour wheel: virtual colour wheel with presets
• Macros: several pre-build pixel macros with adjustable speed
DYNAMIC EFFECTS
• Pixel patterns: pre-programmed dynamic and static patterns
• FX generator: adjustable foreground/background colour, index, speed, direction
• Static colour mode: selection of static colour
• Manual colour mode: manual adjustment of dimmer and strobe
• Auto mode: built-in programs with execution speed adjustment
BODY
• Hardware on-board: fixture for independent use, adjustable height of the base
• Body: sturdy die-cast aluminium body conceived for long-time durability
• Body colour: black with white wash strips
• Other: Stand-up usable as accessorie for increase height of installation
CONTROL
• Control units: WDMX
• Protocols: DMX512
• DMX channels: 8 / 15 / 18channel
• Pixel control: 4 pcs strips pixel2pixel controllable all together
• W-DMX: included, wireless solution receiver
• Display: black OLED high resolution display
• Firmware upgrade: yes, via USB-DMX interface (UPBOX2) not included
• Hibernation: power safe mode when lost DMX
• IR: infrared sensor controlled by remote
ELECTRONICS
• Dimmer: linear 0~100% electronic dimmer
• Strobe / shutter: 1-25 Hz, electronic
SMARTOWER - SMARTOWERPACK
4
• Operating temperature: -20° ~ +40°
• Flicker: flicker free operation
BATTERY
• Battery: 14.8V Lithium batteryV
• Estimated battery life in colour change mode up to: 12h
• Estimated battery life in single colour mode up to: 18h
• Estimated battery life in full-mode up to: 6h
• Re-charge time: 6h/max
• Battery status: shown on display
• Other: recharge available throught fast recharge adaptor available under the base
PHYSICAL
• Cooling: natural cooling of the peculiar chassis and to absence of fans
• Sospension and fixing: M10 threaded insert for easy clamp installation
• Adaptors: fast recharge adaptor available under the base
• Signal connection: WDMX
• Power connection: Adaptor base with external charger
• IP rating: 65 for temporary outdoor application, not for fixed installation
• Dimensions (WxHxD): 119x632x119mm
• Weight: 6kg
Technicaldrawing Fig.1
632
Ø119
5
SMARTOWER - SMARTOWERPACK
1.3 SMARTOWERPACK (optional)
The pack includes:
• 6 pcs SMARTOWER
• 1 Flight case with integrated battery charger kit
• 1 IR controller
• 1 PowerCON power cable
NOTE
Always charge with
flight-case open
671
600 600
117
788
Fig.2
Technical drawing
SMARTOWER - SMARTOWERPACK
6
1.4 OPERATING ELEMENTS AND CONNECTIONS
Fig.3
1. ON/OFF SWITCH
2. IR RECEIVER SIGNAL
3. CONTROL PANEL with LCD display and 4
button used to access the control panel
functions and manage them.
4. TOP COVER
5. HOLE for tripode stand.
6. Base for recharge operations through
magnetic charge in case.
7. HOLE for secutity cable.
12
4
7
6
5
3
7
SMARTOWER - SMARTOWERPACK
1005 mm
39.57 in
1610 mm
63.38 in
CLAMP
SECURITY
CABLE
2.1 MOUNTING
The SMARTOWER can be placed on a solid plane. Moreover, thanks to the (optional) extendable stand,
it can exceed a height of 1.6m (fig.4). As you can see in the illustration, you have to insert the coupling
system in the appropriate seat of the plate where it is locked with a clockwise rotation (until the stop).
Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. The mounting
place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight. When
carrying out any installation, always comply scrupulously with all the regulations (particularly regarding
safety) currently in force in the country in which the fixture’s being used.
- 2 - INSTALLATION
Fig.4
SMARTOWER - SMARTOWERPACK
8
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Switch on the SMARTOWER with the power switch.The unit is ready for operation and can be operated via
a DMX controller or it independently performs its show program in succession.
After operation, switch off the unit with the power switch.
3.2 BASIC
The SMARTOWER has a OLED display and 4 button used to access the control panel functions and manage
them (fig.5).
3.3 RECHARGE PROCESS
To recharge the SMARTOWER, use the Flight-case or use the IP connector for the quick magnetic charger.
Fig.5 - Functions of the buttons
MODE / ESC UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in
a function
Used to select and store the
current menu or confirm the
current function value or
option within a menu
MODE
/ ESC
UP DOWN ENTER
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Equipo de DJ de ProLights
ProLights
ProLights STARK1000 Manual de usuario
ProLights
ProLights TRIBE AQUA Manual de usuario
ProLights
ProLights ARCLED7307HD Manual de usuario
ProLights
ProLights POLAR500 Manual de usuario
ProLights
ProLights DISPLAYCOBTRWDFC Manual de usuario
ProLights
ProLights SOLAR27Q Manual de usuario
ProLights
ProLights SMARTBATHEX Manual de usuario
ProLights
ProLights V575WASH Manual de usuario
ProLights
ProLights LUMIPAR12HPRO Manual de usuario
ProLights
ProLights SUPERFLOWER DMX led Manual de usuario
ProLights
ProLights TRIBE TRUSSPOD3T Manual de usuario
ProLights
ProLights PIXIEWASH Manual de usuario
ProLights
ProLights Mobiblast Manual de usuario
ProLights
ProLights LEDPINSPOT Manual de usuario
ProLights
ProLights ECLIPSE FRESNEL TU Manual de usuario
ProLights
ProLights ECLIPSETU Manual de usuario
ProLights
ProLights MINIECLIPSE Series Manual de usuario
ProLights
ProLights DISPLAYCOBFC Manual de usuario
ProLights
ProLights PHYRO1200SNOW Manual de usuario
ProLights
ProLights DOTQ Manual de usuario
Manuales populares de Equipo de DJ de otras marcas
thomann
thomann Stairville DJ Lase 40-G MK-III Manual de usuario
Eagletone
Eagletone 6 Eyes Flower Manual de usuario
EuroLite
EuroLite FLD-1508 Manual de usuario
Technical Pro
Technical Pro LG8xSEA Manual de usuario
JB Systems
JB Systems Lounge Laser DMX Manual de usuario
Lightmaxx
Lightmaxx Vega Halo 90 Manual de usuario
Elation
Elation FUZE WASH Z350 Manual de usuario
Maverick
Maverick MK3 WASH Manual de usuario
Infinity
Infinity TF-260C7 Fresnel Manual de usuario
Chauvet
Chauvet EVE E-50Z Manual de usuario
Eliminator Lighting
Eliminator Lighting E 138 Manual de usuario
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario