PR Lighting JNR BWS 350 Manual de usuario

JNR BWS 350

JNR-8152A

PR LIGHTING LTD.

http://www.pr-lighting.com

1582 Xingye Avenue, Nancun Panyu

Guangzhou, 511442 China

TEL: +86-20-3995 2888

.01.

If the device has been exposed to temperature changes due to environmental changes,

do not switch it on immediately. The arising condensation could damage the device.

Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.

During initial star t-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively

replaced by the manufacturer or his service agent or a similar qualified person in order

to avoid a hazard.

This device has left the factory in perfect condition. In order to maintain this

condition and to ensure a safe operation, it is absolutely necessary for the user to

follow the safety instructions and warning notes written in this user manual.

CAUTION

Becareful with your operations.With a dangerous voltage you cansuffer a

dangerous electric shock when touching wires!

IMPORTANT

Damages caused by the disregard of this user manual are not subject to warranty.

The dealer will not accept liability for any resulting defects or problems.

SAFETY INSTRUCTIONS

.14.

Prism

rotation

Frost

Zoom

fine

Focus

fine

Auto

focus

Strobe

Dimmer

Blank

Macro 1

Macro 2

Macro 3

Macro 4

Macro 5

Macro 6

Macro 7

Macro 8

Macro 9

Macro 10

Macro 11

Macro 12

Macro 13

Macro 14

Macro 15

Macro 16

Prism rotation and indexing

Counterclockwise rotation from fast to slow

Blank

Clockwise rotation from fast to slow

Blank

Frost

Linear zoom

Zoom fine

Focus

Focus fine

Auto focus

No function

Strobe off

Shutter open,full lamp power

Strobe-effect from slow to fast

Shutter open

Opening pulse in sequences from slow to fast

Closing pulse in sequences from fast to slow

Shutter open

Random strobe-effect from slow to fast

Shutter open,full lamp power

Linear dimmer

Blank

128-135

136-143

144-151

152-159

160-167

168-175

176-183

184-191

192-199

200-207

208-215

216-223

224-231

232-239

240-247

248-255

0-127

128-191

192-193

194-255

0-64

65-255

0-255

1-128

129-255

0-31

32-63

64-95

96-127

128-143

144-159

160-191

192-223

224-255

0-255

Thank you for choosing our JNR BWS 350. For your own safety, please read this

manual before installing the device. This manual covers the important information

on installation and applications. Please install and operate the fixture with following

instructions. Meanwhile, please keep this manual well for future needs.

The is made of a new type of high temperature strength of engineering

plastics and cast aluminum casing with nice outlook . The fixture is designed and

manufactured strictly following CE standards, complying with international standard

DMX512 protocol. It’s available independently controlled and linkable with each

other for operation. And it is applicable for large-scale live performances, theater,

studio, nightclubs and discos.

The adopts 1*350W YODN lamp which features high brightness and

stability. Please carefully unpack it when you receive the fixture and check whether it

is damaged during the transportation. And please check whether the following

items are included inside the box:

JNR BWS 350

.02.

UNPACKING

①

JNR BWS 350

Signal Cable

Power Cable

Omega Clamp

Safety Cable

User Manual

1PC

2PC

1PC

①

②

③

④

⑤

⑥

④

⑤⑥

②

③

Euro Standard UK Standard

USA Standard

OPTIONAL

.13.

160-167

168-175

176-183

184-199

200-201

202-221

222-223

224-243

244-249

250-255

0-8

9-17

18-26

27-35

36-44

45-53

54-62

63-71

72-80

81-89

90-97

98-106

107-115

116-124

125-133

134-142

143-151

152-160

161-169

171-179

180-217

218-255

0-127

128-177

178-203

204-255

0-255

0-19

20-49

50-75

76-105

106-127

Rotation

gobo

wheel

Gobo

Rotation

Blank

Gobo 10

Beam reducer 1

Beam reducer 2

Beam reducer 3

Blank

Forwards gobo wheel rotation from fast to slow

No rotation

Backwards gobo wheel rotation from slow to fast

Random gobo selection by audio control

Auto random gobo selection from fast to slow

Blank

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Shaking gobos from slow to fast

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Gobo 9 Stop

Gobo rotation from fast to slow

Gobo rotation from slow to fast

Gobo indexing

Counterclockwise rotation from fast to slow

Stop

Clockwise rotation from fast to slow

Blank

16-facet linear rotating prism -indexing

16-facet linear rotating prism-rotation

Blank

.03.

Features

FEATURES & SPECIFICATIONS

.12.

A YODN 350W lamp included

Electronic ballast

2200 Hours lamp life span

No need for adjustment of reflector or lamp

High resolution anti-reflection glass lenses

540°PAN and 270° TILT movement

Automatic Pan / Tilt position correction

16-bit smooth and precise resolution for PAN/TILT movement

Fast, quiet and accurate Pan / Tilt positioning

Rotating gobo wheel with 12 rotatable, indexable and interchangeable gobos plus open

Variable speed gobo scrolling in both directions

15.4mm external diameter, 13mm image diameter (Gobo Size)

Static gobo wheel with 17 gobos plus open

Color wheel with total 13 colors plus open

Two color modes (Full color mode and half-color mode)

Variable direction rainbow effect with speed adjustable

8-Facet circular prism with speed adjustable and variable direction

16-Facet circular prism with speed adjustable and variable direction

Prisms combined available

Variable Frost Filter (Hybrid effect for Wash)

Macro-function for gobos/prism combinations

Dual flag mechanical dimming system

Variable speed strobe effect

Preset variable/random strobe and dimming pulse effects

Motor driven focus from near to far

Linear motorized ZOOM (0.5°-25°)

ZOOM range: 0.5°-10° beam application; 5°–25° spot application

2 DMX channel modes, 16CH and 24CH (USITT DMX-512)

DMX, stand-alone, master/slave, sound activated mode

DMX recorder and edit function integrated

2.4” TFT LCD touch screen display with 4 control buttons

POWRECON connector IN

3-Pin&5-Pin XLR connectors IN/OUT

Fan cooling system

Constant temperature readout / management function

DB rating @ 1M = 54,18db

2 x 1/4 turn fastening Omega clamps

1 x Safety attachment point

•

Purple

White

Deep red

Dark yellow

Deep blue

Green

Magenta

Yellow

Blue

Dark green

Rose

Amber

Lower the temperature

Blue fluorescence

Purple

from to

Blank

Gobo 1

fast slow

slow fast

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

Gobo 10

Beam reducer 1

Beam reducer 2

Beam reducer 3

Shaking gobos from slow to fast

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 9

117-127

128-129

130-134

135-138

139-143

144-147

148-152

153-157

158-161

162-166

167-171

172-176

177-180

181-185

186-189

190-222

223-255

0-255

0-3

4-9

10-15

16-21

22-27

28-33

34-39

40-45

46-51

52-57

58-63

64-69

70-75

76-87

88-95

96-103

104-111

112-119

120-127

128-135

136-143

144-151

152-159

10 Gobo

Wheel

OPERATION INSTRUCTIONS

.04.

PHOTOMETRIC DATA

.11.

DMX CHANNELS

PAN

Fine

/ speed

Blank

Eco mode(Lamp power 230W)

Standard mode(Lamp] power 280W)

Blank

PAN/ speed mode

PAN/ time mode

Blackout while Pan/Tlit moving

Disabled blackout while Pan/Tilt moving

Blackout while color wheel moving

Disabled blackout while color wheel moving

Blackout while gobo wheel moving

Disabled blackout while gobo wheel moving

Lamp On,reset(total reset except Pan/Tilt)

PAN/TILT reset

Color system reset

Blank

Total reset

Blank

Lamp off

Blank

Open/White

Deep red

Dark yellow

Deep blue

Green

Magenta

Yellow

Blue

Bark green

Rose red

Amber

Lower the termperature

Blue fluorescence

PAN

TILT

TILT PAN

TILT

0-255

0-19

20-24

25-29

30-49

50-59

60-69

70-79

80-89

90-99

100-109

110-119

120-129

130-139

140-149

150-189

190-199

200-209

210-229

230-239

240-255

0-8

9-17

18-26

27-35

36-44

45-53

54-60

63-71

72-80

81-89

90-98

99-107

108-116

Mode/Channel

Function Values Description

Basic

Standar

PAN

PAN-fine

TILT

-fine

/PAN

Macro

Color

Wheel

TILT

· The JNR BWS 350 is for beam effect for on-site decoration purpose.

· Don’t turn on the fixture if it’s been through severe temperature difference like

after transportation because it might damage the light due to the environment

changes. So make sure to operate the fixture until it is in normal temperature.

· This light should be keep away from strong shaking during any transportation or

movement.

0.5-25°Beam Angle LUX 0.0929=FC×

Photometric Beam Angle Data

Input Voltage:

Lamp :

Control Signal:

Control Channel:

Power Consumption:

Dimensions:

Packing Dimensions:

Net Weight:

Gross Weight:

Quantities

AC100-240V 50/60Hz

1*350W YODN lamp

DMX512, master-slave and sound activated or auto operation

24/16DMX channels USITT DMX-512

500W

380(D)*260(W)*600(H)mm

465(D)*450(W)*680(H)mm

19kg

22.6kg

600

260380

Specifications

Beam

Diameter

ø 0.28 ø 0.56 ø 0.85 ø 1.13 ø 1.41

52898/

569411

0.5°

5m 10m 15m 30m

20m 25m

13224/

142353

5877 /

63267

3306 /

35588

2115 /

22776

1469 /

15816

ø 1.69

( FC/

LUX )

25°

.05.

Cautions: For added protection mount the fixtures in areas outside walking paths,

seating areas, or in areas were the fixture might be reached by unauthorized

personnel.

Before mounting the fixture to any surface, make sure that the installation area can

hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such

as an appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the

fixture.

from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture

is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails.

INSTALLATIONS

.10.

Cho ose lamp on/off by console

Ret urn to manual

Display 180° reverse

Language

Esc

Lamp

Setting

mechanical parts.

· Don’t expose the fixture in overheat, moisture or environment with too much dust

when installing it. And don’t lay any power cables on the floor. Or it might cause

electronic shock to the people.

· Make sure the installation place is in good safety condition before installing the

fixture.

· Make sure to put the safety chain and check whether the screws are screwed

properly when installing the fixture.

· Make sure the lens are in good condition. It’s recommended to replace the units if

there are any damages or severe scratch.

· Make sure the fixture is operated by qualified personnel who knows the fixture

before using.

· Keep the original packages if any second shipment is needed.

· Don’t tr y to change the fixtures without any instruction by the manufacturer or

the appointed repairing agencies.

· It is not in warranty range if there are any malfunctions from not following the

user manual to operate or any illegal operation, like shock short circuit, electronic

shock, lamp broke, etc.

Don’t pull up the light by only the head, or it might cause damages to the

.06.

① Omega Bracket

② Satety Clamp

③ Safety Cable

④ 1/4 Turn Quick-Lock Fasteners

.9.

②

1/4 Turn 1/4 Turn

①

③

④

Regardless of the rigging option you choose for your , always be sure to

secure your fixture with a safety cable. The fixture provides a built-in rigging point for

a safety cable on the hanging bracket as illustrated above. Be sure to only use the

designated rigging point for the safety cable and never secure a safety cable to a

carrying handle.

JNR BWS 350

Yes

Ent er

Bac k

Ent er

Bac k

CH1 -CH32

1-7 Volume

alw ays

30 Se conds

20 Se conds

10 Se conds

No Re turn

10 Se conds

20 Se conds

30 Se conds

Off

Fac tory reset

Sav e the setting

Bac k Home manual display

All M otor self check

Bac k last step

Sma ll Motor self check

Bac k Last step

Sca n motor self check

Bac k last step

Run M acro program

Bac k last step

Mac ro run by sound

Bac k last step

Man ual control relevant

Cha nnels function

Bac k home manual display

Sho w DMX value

Sho w fixture work and

sof tware info

Dis play fixture error info

Bac k home manual display

Hig hter mean display more

bri ght

Dis play always on

Dis play no operation 30

sec onds display being dark

Dis play no operation 20

sec onds display being dark

Dis play no operation 10

sec onds display being dark

Dis play no operation Manual

no re turn

Dis play no operation 10

sec onds Back home Manual

Dis play no operation 20

sec onds Back home Manual

Dis play no operation 30

sec onds back home manual

No si gnal display normal

No si gnal display will flash

Bac k last step

Sav e the setting

Bac k home manual

Lig ht up if power on

Man ual control the lamp on/off

Reset

Save

Back

Fixture Reset

Test

Analog console

Back

Channel level

Other Info

Error Info

Back

Brightness

Manual back

Back light

Flashing

Back

Save

Back

Default

Manual control

Back light delay

Manual

Setting

Inquire

Display

Setting

All Motor

Some Motor

XY Motor

Auto

Sound

Mounting points: Overhead mounting requires extensive experience, including

amongst others calculating working load limits, a fine knowledge of the installation

material being used, and periodic safety inspection of all installation material and the

fixture. If you lack these qualifications, do not attempt the installation yourself.

Improper installation can result in bodily injur y.

Be sure to complete all rigging and installation procedures before connecting the

main power cord to the appropriate wall outlet.

Clamp mounting: The provides a unique mounting bracket assembly

that integrates the bottom of the base, and the safety cable rigging point in one unit

(see the illustration below). When mounting this fixture to truss be sure to secure an

appropriately rated clamp to the included omega bracket using a M10 screw fitted

through the center hole of the “omega bracket”. As an added safety measure be sure

to attached at least one properly rated safety cable to the fixture using on of the

safety cable rigging point integrated in the base assembly.

JNR BWS 350

.8..07.

Connect the provided XLR cable to the female 3-pin XLR output of your controller and

the other side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core,

screened cable with XLR input and output connectors. Please refer to the diagram

below.

DMX-512 connection with DMX terminator

DMX-512 CONTROL CONNECTIONS

POWER IN

POWER SWITCH

DMX IN

DMX OUT

MENU OPERATIONS

ESC

DOWN

FUNC(CONFIRM)

Operation of LCD display

Manual Sub Manual 1 Sub Manual 2 Function Details

DMX m ode

Wir eless

mod e

Aut o mode

Sta ndard

Sim plify

Cus tom

Off

540

360

Off

Cle ared

Sav e

Haf t color

Ful l color

Off

Cho ose Fixture

rec eive signal

mod e

Cho ose fixture

run ning CH

PAN scan forward

PAN scan reverse

TILT scan f orward

TILT scan r everse

PAN 540°running

PAN 360°running

On sc an correction function

Off scan c orrection function

Bac k to Initial after function

Sta y last value after signal cut

Ena ble haft color function

Dis able haft color function

Effect w heel back zero from

sho rtes troute

Effest w heel back zero from

run ning direction

Bac k last step Manual

Ple ase contact the dealer

or me nu facturer

Running

mode

PAN reverse

TILT

PAN degree

Optocoupler

detection

No DMX

signal

Color wheel

Shortest

Distance

Back

Advance setting

mode

Channel

reverse

Setup

Nul l

Adj ustment

CH de finition

Fac tory set

Use

Man agement

Bac k

For installations where the DMX cable has to run a long distance or

is in an electrically noisy environment, such as in a discotheque, it

is recommended to use a DMX terminator. This helps in preventing

corruption of the digital control signal by electrical noise. The DMX

terminator is simply an XLR plug with a 120 Ω resistor connected

between pins 2 and 3,which is then plugged into the output XLR

socket of the last fixture in the chain. Please see illustrations below.

PIN3

PIN2

120 Ω

DMX Out put

5-Pin X LR Socket

DMX Inp ut

5-Pin X LR Socket

1:Gro und

2:Dat a(-)

3:Dat a(+)

COMMO N

DMX+

DMX-

DMX51 2 IN

5-PIN X LR

DMX51 2 OUT

5-PIN X LR

123

234

DMX Out put

3-Pin X LR Socket

DMX Inp ut

3-Pin X LR Socket

1:Gro und

2:Dat a(-)

3:Dat a(+)

1 2

COMMO N

DMX+

DMX-

DMX51 2 IN

3-PIN X LR

DMX51 2 OUT

3-PIN X LR

2 1

Wireless

FUSE

SELECT SIGNAL SIGNAL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de PR Lighting

PR Lighting

PR Lighting JUNIOR JNR-8146C Manual de usuario

PR Lighting

PR Lighting XR-230 BEAM Manual de usuario

PR Lighting

PR Lighting XR 380 Beam Manual de usuario

PR Lighting

PR Lighting XR480S BWS Manual de usuario

PR Lighting

PR Lighting PR-8110 Manual de usuario

PR Lighting

PR Lighting XLED 3007 Manual de usuario

PR Lighting

PR Lighting XRLED 300 SPOT Manual de usuario

PR Lighting

PR Lighting MEGA COLOUR 2000 Manual de usuario

PR Lighting

PR Lighting XRLED 3000-W Framing Manual de usuario

PR Lighting

PR Lighting SOLO 575 Manual de usuario

PR Lighting

PR Lighting LED STUDIO 3605 Manual de usuario

PR Lighting

PR Lighting AQUA LED 600 SPOT Manual de usuario

PR Lighting

PR Lighting ARC LED 1054 Manual de usuario

PR Lighting

PR Lighting AQUA 580 BEAM Manual de usuario

PR Lighting

PR Lighting StarBrite Manual de usuario

PR Lighting

PR Lighting XL 1200 Manual de usuario

PR Lighting

PR Lighting JNR DOT BEAM Manual de usuario

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Manual de usuario

PR Lighting

PR Lighting JNR PAR COB Manual de usuario

PR Lighting

PR Lighting LED Studio 3800T Manual de usuario

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Manual de usuario

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Manual de usuario

PR Lighting

PR Lighting PR-8102 Manual de usuario

PR Lighting

PR Lighting PR-8330 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario