PR Lighting XR-230 BEAM Manual de usuario

XR-230 BEAM

PR-2207

The user manual contains important information aboutthe safe installation and use of a projector. Please read and

followtheseinstructionscarefullyand keep the manualin asafeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

SAFETYANDWARNINGS……………………………………………………………………………………………

INSTRUCTIONS…………………………………………………………………………………………………………

APPERANCE……………………………………………………………………………………………………………

INSTALLTION……………………………………………………………………………………………………………

SETUPANDTONFIGURATION…………………………………………………………………………………………

OPERATIONMENU……………………………………………………………………………………………………

DMXPROTOCOL ………………………………………………………………………………………………………

SIGNSONTOUCHSCREEN …… ……………………………………………………………………………………

ERRORMESSAGES………………… ………………………………………………………………………………

10.

TECHNICALDATA……………………………………………………………………………………………………

11.

CIRCUITDIAGRAM …………………………………………………………………………………………………

12.

COMPONENTORDERCODES………………………………………………………………………………………

APPENDIX…………………………………………………………………………………………………………

ACCESSORIES

The following itemsare supplied with theprojector andpleasecheck:

Name

Quantity

Unit

Remark

GClamp

XLR Connectors

Set

MaleandFemale

SafetyCord

User manual

QRcode

Ω Clamp

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in

good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not

use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

Any future technical change in the user manual won’t be with any notice.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from the

delivery date but the light source is not within the warranty

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

thesafety informationhereinafter!

Thefollowingsafetysignsare usedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any damage

caused bytransportation,consultyourdealerand do notuse it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector as

he/shelikes

●Please be notedthat thedamage causedbychangingtheprojector at will is notwarranted.

● Donothesitate to contactthe dealer or the manufacturer if any questions or advice.

●Ifa lamp isdamagedordeformsbecauseofheat, it should bereplaced.

● Theprojector is forindooruseonly,IP20.

● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not allow

contact with wateroranyother liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while being

operated

●The projector is only intended for installation, operation and maintenance byqualified personnel. And the operation

muststrictlyfollowtheproceduresinthemanual

●Norepairableparts intheprojectoranddonotopencoversfor maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do notconnectaprojectortoany typeofdimmerpack.

●Ifthelamp,lensandscreenprotective coveroftheaprojectorhaveobviousdamage,i.e.,to theextent thatit hurtsthe

performancelikecrackingordeformation.Please stop usingitandreplace themwith theoriginalparts,otherwise its

performance willbe compromised.

●Fortheinstallationlocationofaprojector,itshouldn’t be seen in the distance of less than 4 meters for a long time.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a projector

while covers(housing)areoff

●Keep thelamp cleananddonot touchit withbarehands.

●Whileoperating it,wearprotective items.

●Anyelectricalconnectionmustbecarriedoutbyaqualifiedperson.

●Beforeinstallation,pleaseconfirmthevoltagesupplied matcheswhatisrequired fortheprojector

●Eachprojectormustbeproperlyearthed andinstalled asper relatedelectrical standards.

●Do notuse power cordwithitsinsulatordamaged and connectthepowercordwithother cables.

●If the projectoris notused or under cleaning,, pleasehold the plug and unplugit. Do not unplug it forcefullyorby

pullingthepowercable.

●Allpowercords mustconformto relatedsafety andregulations

●Whilebeingoperated, theprojectorshouldnotbeunder rainsor inhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord

supplied throughthesafetycordholesfor safetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power

mains.

●.Afterstableoperationunder normal situation, its temperatureis80℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean theprojectorhas some defects.

●While it running, don’t touch the metal housing to avoid being burned!

●Donotmounttheprojectordirectlyoninflammablesurface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated itemsis18m.

●Aprojector should be installed with good ventilation and the minimum distance between the projector and

wallsis50cm.Atthesametime,pleaseensurethe fansandairinletsandoutletsare workable.

●Donotletthe frontlensundersunlightorother stronglight sourcesatanyangle,otherwise thedanger

offirecanbecaused bythe focused beambythelensinside aprojector.

●TheproductmeetsTheGeneralTechnicalRequirementsandStandards for RecycleandUseOfExpired

Applianceand Electronic Products.

●Whentheproductmeets disposalstandardsand needs tobedisposed,aclient needstodisposeandrecycle it.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

Under normal running, the protective units ofa projector should be inspected regularly like power fuse. If it is burned, please install a

newoneandensureitisthesameratingastheburned one.

For a projector with an over-temperature protective unit, please inspect cooling units regularly like cooling fans, heat sink and other

cooling parts. Please check if the fans run normally or fans and air inletsareblocked by dust. To keep air inlets/outletsclean, cooling

fansshouldbecleanedevery15days.

For projectors with lens, reflectors and coated filters, the accumulation of oil, smoke and dust on them will compromise the light

output. Cleaning a projector is very necessary to ensure a reliable use. Internal and externallens, flat glass, reflector and coated filters

needtobecleanedperiodicallytooptimizelightoutput.

Cleaningfrequencyis to bedecided byoperationsand its environment. Usesoft cloth and normaldetergent for glass forcleaningwork.

It’s advised external opticalsystem be cleanedevery 20days and internaloptical systems every30/60days. Fora projector withhigh IP

rating, ifno damage inside, itis advised to cleanthe surfacesof itshousingin principle. Keep lens clean and do not touchopticalparts

withbarehands.

●Beforeanymaintenanceandcleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowedtodomaintenance

●Duringmaintenanceandbefore maintenance, theprojectormustbeoffpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

itrunsornot

●Do notuse alcoholor otherorganicsolventtocleanthehousingtoavoiddamage.

●Do notuseany solvent withchemicalelementstocleancolorfiltersorhotmirror.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and focus

lensbelubricatedevery2months.Highqualityandhightemperature lubricant/grease isadvised..

●TROUBLESHOOTING

PROBLEM

ACTION

Theprojectordoesn’t switch on

Checkthefuseonthepower socket.

Checkthelamp.

Thelampison but the projector doesn’t respond

to thecontroller

Makesurethatthe fixture’s start address is right

ReplaceorrepairtheXLR signalcable.

The projectorfunctions intermittently

Makesurethefanisworkingwellorfansandtheirshieldsarenotblocked

Beamappearsdim, Lowinbrightness

Make sure thelamp is withinitslifespan

Removedustor grease from thelenses.

Theprojectimageappearstohavea halo

Carefullycleanthelamp,opticallensesandothercomponents.

HeavilyDefectiveBeam

Checkif lensareingoodcondition(notcracked)

Cleandustor greaseonthelens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a projector

withpowerwhileitis locked.

Head

Arm

Base

Take2 clampsandthesafetycordoutfromthepackageand mount2clampsontheundersideoffixture with2retainersattachedtoeach

clamp.Hangthefixtureonthe structureandfastenthescrewsattachedtoeachclamp.(SeetheWARNINGontheundersideofthe base as

shownabove)TopasstheSAFETYCORDthroughtheHOLESforsafety!Always ensurethattheprojectorisfirmlyanchoredto

avoidvibrationandslippingwhilstfunctioning.Always ensurethatthestructurethatyouaregoingto mounttheprojectortoissecure and

strongenoughtosupport the weight.

WARNING:

●TheprojectorMUSTbelifted orcarried by theHANDLES insteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connect thepowercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projectorbeconnectedwithpowerseparatelysothattheymaybeindividuallyswitched onandoff.

●The earth wire(yellow/green)mustbe connected to the ground. Andelectrical connection

mustbeinaccordance withthestandardsconcerned.

●If any questions about the electrical installation, do not continue but consult a qualified

electrician.

●DMXCONTROLCONNECTION

Remarks:

1. The Distance between the top of

thefeetandthetop thehead;

2. The distance between the top of

the mounting bar and the top of

thehead;

3. The head’s rotating diameter( the

minimum distance between 2

neighboring projectors on the

truss)

Warning!

For safety, please run the safety cord

through itshole.

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with each

wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the projector)

or5pin XLR plugs and sockets.TheXLR'sare connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets mustn’t

be connected in any way other than mentioned in the above figure. The XR330BWS accepts digital control signals in protocol DMX512

(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second fixture’s

DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX terminator asshown

inthefigurebelow.

●DMXTERMINATOR

Inthe Controller mode, at the last fixture inthe chain, theDMX output hasto be connected with a DMXterminator. Thispreventselectrical

noisefromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged into

theoutputsocketonthelastprojectorinthechain.Theconnectionsareillustratedbelow.

● ALIGNMENT/INSTALLATION/REPLACEMENTOFALAMP

Lockthe yoke before fitting/replacing/adjustingthe lamp. Just as Shown by Figure 1, Open the lamp chamber cover byloosening4 fastfit

screws,.

Removal/Installationofalamp as figure2

Controller

OutputInputTerminator OutputInput

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

示例1：松开8颗快速安装螺丝

Loosen8screws

Figure2:lampadjustment

Toadjust thelampasperFigure3.

Beforethe removalofalamp, unplug bothlamp wires.Plugbothlamp wiresafter itsinstallation.

●Don’t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to impair the

beam output. While lamp’s installation,donot damage themetal wire around theburner.

●Pleaseread"Instructions" enclosedwiththelampcarefullywhileinstallinglamp.

●Donotoperatethe projectorwhileadjustingthelamp.

5. SETUPAND CONFIGURATION

●FRONTPANELOPERATION

DMX addressand Functions canbe setsimplyandconvenientlyviabuttons andLCDdisplay.

To browse through or change the projector ’s settings, press ENTER key for more than 5s to unlockthe screento showits function menus.

Eachmainmenuhasitssub-menus.And eachmenustandsforspecialfunction.Forthedetails,pleaseseebelow:

示例2：调节灯泡

1、用十字螺丝刀拆开两侧风扇组

件螺丝，打开风扇

2、用十字螺丝刀调松灯泡一测的

压紧螺丝

3、用十字螺丝刀调节两颗螺丝即

可调节灯泡位置

示例3：取灯泡

1、先旋送灯泡一侧的压紧螺丝；

2、将两根灯泡线取下，将灯泡向

上推倾斜取下灯泡。

FUNC

DOWN

ENTER

1.Use a cross-screwdriver to

remove the screws of fanson its

bothsides;

2. Use a cross-screw driver to

loosen the tightening screw on

one sideofthelamp;

3. Use cross-screw driver to

adjust both screws to adjust the

lamp’s positions.

1. Loosen the tightening screw

ononeside ofthelamp.;

2.Unplugbothlampwires,push

the lamp upwardandremoveit

obliquely

Before the removal of a lamp, unplug both

lamp wires. Plug both lamp wires after its

installation.

Tosetorbrowse throughits functions,press UP or DOWN key.

Press ENTER keyto savethechangesorenterintothe submenus.Press UP or DOWN key tochangethenumbers(minusorplus).

Press FUNC keyto gotothe uppermenu.If FUNC keyisnotpushed, thesystemwillgo back toinitialstatusautomatically.

●DMXSTARTADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from thecontroller.

The projector has3DMX modes. There are standard mode ,short mode and extended mode. For example standard mode has 14 channels,

so set the No. 1 projector’s address 001, No. 2 projector’s address 015, No. 3 projector’s address 029,No. 4 projector’s address 43, and so

on.

SwitchontheProjector.Press ENTER keymorethan5secondstounlockthecontrolpanel,

Press ENTER toshowDMXaddress

Press UP or DOWN keyfortheDMXaddressdesired.

Press ENTER keyto confirmit.Afterpoweronnexttime, thevaluesaved lasttimewillbedisplayed.

Press the FUNC keyto gobacktotheupper levelmenu.

●DMXWIRELESSCONTROL(Onlyforfixtureswithwireless control)

Theprojectorhaswirelesscontrolfunctionwithwirelessreceiver moduleandantennaforremotecontrol.

Thesetupofitisbelow:

1.PressOKformorethan3stounlock thecontrol panel,thenpress UP or DOWN key toenterintotheoperationmenuand select

“Config Settings”.

2. Select “Wireless Only” from the menu of “Signal Select”.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press

“Enter” for the menu of Un-link Wireless under the upper level menu of Config Settigns , then the fixture is unlinked with the

wireless transmitter.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the last

fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can be

setaccordingly.

AfterPoweredon,the groupwillruninMaster/Slave Mode

6. OPERATIONMENU

1st levelmenu

2nd levelmenu

3rd levelmenu

4th levelmenu

5th levelmenu

Address

DMXAddress

1-500（ShortMode）

1-499（StandardMode）

1-497（ExtendedMode）

Reset

TotalReset

ReallyReset?

ConfirmorCancel

Pan&TiltReset

ReallyReset?

ConfirmorCancel

ColourSystemReset

ReallyReset?

ConfirmorCancel

GoboReset

ReallyReset?

ConfirmorCancel

Dimmer/StrobeReset

ReallyReset?

ConfirmorCancel

Fo.Fr.Pr.Reset

ReallyReset?

ConfirmorCancel

ConfigSettings

DMXChannelMode

Short 13CH

Standard 14CH

Extended16CH

ViewSelectedMode

CH01 Strobe

CH02 Dimmer

…

CHXXX Control function

LampControl

OFF/ ON

On By Power On

OFF/ ON

ControlByDMX

OFF/ ON

ECOPower

OFF/ ON

OutputInputTerminator

MasterSlaveSlave

OutputInput

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de PR Lighting

PR Lighting

PR Lighting OMEGA Manual de usuario

PR Lighting

PR Lighting JNR BWS 350 Manual de usuario

PR Lighting

PR Lighting AQUA LED 600 SPOT Manual de usuario

PR Lighting

PR Lighting ARC LED 1054 Manual de usuario

PR Lighting

PR Lighting StarBrite Manual de usuario

PR Lighting

PR Lighting XR480S BWS Manual de usuario

PR Lighting

PR Lighting PR-8110 Manual de usuario

PR Lighting

PR Lighting XLED 300 Beam Manual de usuario

PR Lighting

PR Lighting AQUA 580 BEAM Manual de usuario

PR Lighting

PR Lighting XR 1700 FRAMING Manual de usuario

PR Lighting

PR Lighting PR-8330 Manual de usuario

PR Lighting

PR Lighting XRLED 300 SPOT Manual de usuario

PR Lighting

PR Lighting XLED 6007 Manual de usuario

PR Lighting

PR Lighting PR-8102 Manual de usuario

PR Lighting

PR Lighting XRLED 1200 SPOT Manual de usuario

PR Lighting

PR Lighting XL 1200 Manual de usuario

PR Lighting

PR Lighting XLED 250 BEAM Manual de usuario

PR Lighting

PR Lighting PR-3203T Manual de usuario

PR Lighting

PR Lighting XLED 6019 Manual de usuario

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Manual de usuario

PR Lighting

PR Lighting JUNIOR JNR-8146C Manual de usuario

PR Lighting

PR Lighting XPar 336-W Manual de usuario

PR Lighting

PR Lighting LED Studio 3201D Manual de usuario

PR Lighting

PR Lighting AQUA LED 730 FRAMING Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario