PR Lighting JNR DOT BEAM Manual de usuario

The following points have to be considered during the inspection:

1) All screws for installing the devices or parts of the device have to be tightly connected

and must not be corroded.

2) There must not be any deformations on the housing, color lenses, fixations and

installation spots (ceiling, suspension, trussing).

3) Mechanically moved parts must not show any traces of wearing and must not rotate with

unbalances.

4) The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage have to be adhered by a

skilled installer and any safety problems have to be removed.

In order to make the lights in good condition and extend the life time, we suggest a regular

cleaning to the lights.

1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to

accumulation of dust.

2) Clean the fan each week.

3) A detailed electric check by approved electrical engineer each three month, make sure

that the circuit contacts are in good condition, prevent the poor contact of circuit from

overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never

use alcohol or solvents.

There are no serviceable parts inside the device. Please refer to the instructions under

“Installation instructions”.

Should you need any spare parts, please order genuine parts from your local dealer.

MAINTENANCE AND CLEANING

Disconnect from mains before starting maintenance operation.

CAUTION

JNR DOT BEAM

JNR-8127

PR LIGHTING LTD.

http://www.pr-lighting.com

1582 Xingye Avenue, Nancun Panyu

Guangzhou, 511442 China

TEL: +86-20-3995 2888

.01.

If the device has been exposed to temperature changes due to environmental changes,

do not switch it on immediately. The arising condensation could damage the device.

Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.

During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively

replaced by the manufacturer or his service agent or a similar qualified person in order

to avoid a hazard.

This device has left the factory in perfect condition. In order to maintain this

condition and to ensure a safe operation, it is absolutely necessary for the user to

follow the safety instructions and warning notes written in this user manual.

CAU TI ON

Becareful with your operations.With a dangerous voltage you cansuffer a

dangerous electric shock when touching wires!

IMPORTANT

Damages caused by the disregard of this user manual are not subject to warranty.

The dealer will not accept liability for any resulting defects or problems.

SAFETY INSTRUCTIONS

.10.

0-4

5-24

25-49

50-74

75-99

100-124

125-149

150-174

175-199

200-224

225-255

0-255

0-49

50-99

100-149

150-199

200-255

0-250

251-252

253-255

No function

Internal program 1

Internal program 2

Internal program 3

Internal program 4

Internal program 5

Internal program 6

Speed control of internal programs from slow to fast

No function

Static programs (internal programs)

Dynamic programs (internal programs)

Auto running

Sound control

No function

Reset in 3s

No function

Internal program 7

Internal program 8

Internal program 9

Internal program10

Internal

Dynamic

Programs

Reset

Macro

Thank you for choosing our JNR DOT BEAM. For your own safety, please read this

manual before installing the device. This manual covers the important information

on installation and applications. Please install and operate the fixture with following

instructions. Meanwhile, please keep this manual well for future needs.

The is made of a new type of high temperature strength of

engineering plastics and cast aluminum casing with nice outlook. The fixture is

designed and manufactured strictly following CE standards, complying with

international standard DMX512 protocol. It’s available independently controlled

and linkable with each other for operation. And it is applicable for large-scale live

performances, theater, studio, nightclubs and discos.

The adopts which

features high brightness and stability. Please carefully unpack it when you receive

the fixture and check whether it is damaged during the transportation. And please

check whether the following items are included inside the box:

JNR DOT BEAM

JNR DOT BEAM 1 PCS 60W OSRAM LE RTDUW S2WP 4-in-1 LEDs

.02.

UNPACKING

①

JNR DOT BEAM

Signal Cable

Power Cable

Power Out

Omega Clamp

Safety Cable

User Manual

1PC

①

②

③

④

⑤

⑥

⑦

④

⑤

⑥ ⑦

②

③

Euro Standard UK Standard

USA Standard

OPTIONAL

DMX CHANNELS

0-255

0-55

56-155

156-255

0-255

0-55

56-155

156-255

0-255

0-19

20-49

50-64

65-69

70-84

85-89

90-104

105-109

110-124

125-129

130-144

145-149

150-164

165-169

170-184

185-189

190-204

205-209

210-224

225-229

230-244

245-255

0-255

O O

PAN movement 0 ~540

PAN rotation stop

Forwards infinite PAN rotation from slow to fast

Backwards infinite PAN rotation from slow to fast

Fine control of PAN movement

O O

TILT movement 0 ~360

TILT rotation stop

Forwards infinite TILT rotation from slow to fast

Backwards infinite TILT rotation from slow to fast

Fine control of TILT movement

Speed control of PAN/TILT from fast to slow

0...100% Linear dimmer from dark to bright

Strobe OFF

Strobe ON

Strobe effect from fast to Slow

Pulse strobe ON effect from fast to Slow

Strobe ON

Pulse strobe OFF effect from fast to Slow

Strobe ON

Random strobe effect from fast to slow

Strobe ON

Random strobe ON effect from fast to slow

Strobe ON

Random strobe OFF effect from fast to slow

Strobe ON

Thunder 1 strobe effect from fast to slow

Random thunder strobe effect from fast to slow

Strobe ON

Sine strobe effect

Strobe ON

Thunder 2 strobe effect from fast to slow

Strobe ON

0-100% Red dimmer from dark to bright

0-100% Green dimmer from dark to bright

0-100% Blue dimmer from dark to bright

0-100%White dimmer from dark to bright

Strobe ON

Mode/CH Values Description

15CH

PAN

Infinite

PAN

PAN fine

TILT

Infinite

TILT

TILT Fine

Speed

Dimmer

Red

Green

Blue

White

Strobe

.09.

17CH

Function

.03.

Specifications

Input Voltage:

LED Quantities:

Control Signal:

Control Channel:

Power Consumption:

Dimensions:

Packing Dimensions:

Net Weight:

Gross Weight:

Features

AC90-260V 50/60Hz

DMX512,master-slave and sound activated or auto operation

15/17 DMX Channels USITT DMX-512

130W

221(D)*155(W)*290(H)mm

550(D)*800(W)*320(H)mm

5.06kg

6.36kg

1*60W OSRAM LE RTDUW S2WP 4-in-1 LED

FEATURES & SPECIFICATIONS

•

• 50,000 hours lifespan and low power consumption

•

• Outstanding sharp BEAM effect and remarkable wash effect with pure color mixing

• Specific high efficiency 4.5° optic system

•

• Scan position memory, auto reposition after unexpected movement

• High speed strobe effect with 1-25 flashes per second

• 0-100% smooth linear LED dimmer

• Amazing visual effect by pro control

• 10 Internal program available

• Default pixel macros effect for easy performance

• 15/17 DMX Channels USITT DMX-512

• DMX512, master-slave and sound activated controllable or auto operation

• High definition blue LCD display

• Efficient low noise fan cooling system

• POWERCON IN/OUT

• 3-pin XLR connectors IN/OUT

• DB rating@1M=54.18dB

• IP20 protection rating

• -35°C to 45°C ambient temperature

1*60W OSRAM LE RTDUW S2WP 4-in-1 LED

Each color controllable individually

Flicker free sources management

8/16 Bit smooth, fast and precise infinite (continuous) PAN/TILT movement

Random strobe effect and pulse strobe effect available

Constant temperature readout and management function

Two sides handles for transportation

1 Specific hanging system

1x Safety attachment point

•

.08.

For installations where the DMX cable has to run a long

distance or is in an electrically noisy environment, such as

in a discotheque, it is recommended to use a DMX

terminator. This helps in preventing corruption of the

digital control signal by electrical noise. The DMX

terminator is simply an XLR plug with a 120 Ω resistor

connected between pins 2 and 3,which is then plugged

into the output XLR socket of the last fixture in the chain.

Please see illustrations below.

PIN3

PIN2

120 Ω

MENU OPERATIONS

LCD Display

Enter

Down

Func

Slave Signal

Sound Signal

DMX Signal

Mster Signal

001-512

Dmx512

Auto

Sound

15CH

17CH

60S

0-16

0-255

YES

Address

Display

Xrevise

Version

PT Sett

YES

Vx.xx

DMX address setting

DMX 512 mode

Auto mode

Sound mode

15CH mode

17CH mode

Backlight ON

PAN calibration

TILT calibration

PAN reverse ON

PAN reverse OFF

TILT reverse ON

TILT reverse OFF

PAN reset ON

PAN reset OFF

Software version

Reset ON

Reset OFF

Time used

0000-9999

YES

DmxAddr

WorkMod

ChanMod

Tool

SundHig

Xrevise

Xrevers

Yrevers

Xyfbstin

RunTime

Info

Rest

Backlight OFF in 60s

Mic sensitivity

.04.

PHOTOMETRIC DATA

5°Beam Angle LUX 0.0929=FC×

Photometric Beam Angle Data

1059 / 11400 109 / 1170 20 / 210

1m (3.3ft) 3m (9.8ft) 5m (16.4ft)0m (0ft)

(FC/LUX)

741 / 7980 87 / 940 14 / 150

1479 / 15920

1550 / 16680

157 / 1690

165 / 1780

27 / 290

32 / 340

4210 / 45320 447 / 4810 80 / 860

RG B W

5°

36 / 390

27 / 290

51 / 550

62 / 670

150 / 1610

7m (23.0ft)

.07.

DMX Output

3-Pin XLR Socket

DMX Input

3-Pin XLR Socket

1:Ground

2:Data(-)

3:Data(+)

1 2

COMMON

DMX+

DMX-

DMX512 IN

3-PIN XLR

DMX512 OUT

3-PIN XLR

2 1

Regardless of the rigging option you choose for your , always be sure

to secure your fixture with a safety cable. The fixture provides a built-in rigging point

for a safety cable on the hanging bracket as illustrated above. Be sure to only use the

designated rigging point for the safety cable and never secure a safety cable to a

carrying handle.

JNR DOT BEAM

Connect the provided XLR cable to the female 3-pin XLR output of your controller and

the other side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core,

screened cable with XLR input and output connectors. Please refer to the diagram

below.

DMX-512 connection with DMX terminator

DMX-512 CONTROL CONNECTIONS

FUSE

POWER IN

POWER OUT

DMX IN

DMX OUT

POWER SWITCH

POWER IN

DMX IN

· The is for beam effect for on-site decoration purpose.

· Don’t turn on the fixture if it’s been through severe temperature difference like

after transportation because it might damage the light due to the environment

changes. So make sure to operate the fixture until it is in normal temperature.

· This light should be keep away from strong shaking during any transportation or

movement.

· Don’t pull up the light by only the head, or it might cause damages to the

mechanical parts.

· Don’t expose the fixture in overheat, moisture or environment with too much dust

when installing it. And don’t lay any power cables on the floor. Or it might cause

electronic shock to the people.

· Make sure the installation place is in good safety condition before installing the

fixture.

· Make sure to put the safety chain and check whether the screws are screwed

properly when installing the fixture.

· Make sure the lens are in good condition. It’s recommended to replace the units if

there are any damages or severe scratch.

· Make sure the fixture is operated by qualified personnel who knows the fixture

before using.

· Keep the original packages if any second shipment is needed.

· Don’t try to change the fixtures without any instruction by the manufacturer or

the appointed repairing agencies.

· It is not in warranty range if there are any malfunctions from not following the

user manual to operate or any illegal operation, like shock short circuit, electronic

shock, lamp broke, etc.

JNR DOT BEAM

.05.

OPERATION INSTRUCTIONS

Cautions: For added protection mount the fixtures in areas outside walking paths,

seating areas, or in areas were the fixture might be reached by unauthorized

personnel.

Before mounting the fixture to any surface, make sure that the installation area can

hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such

as an appropriate safety cable.

INSTALLATIONS

Never stand directly below the device when mounting, removing, or servicing the

fixture.

from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture

is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails.

Mounting points: Overhead mounting requires extensive experience, including

amongst others calculating working load limits, a fine knowledge of the installation

material being used, and periodic safety inspection of all installation material and the

fixture. If you lack these qualifications, do not attempt the installation yourself.

Improper installation can result in bodily injur y.

Be sure to complete all rigging and installation procedures before connecting the

main power cord to the appropriate wall outlet.

Clamp mounting: The provides a unique mounting bracket assembly

that integrates the bottom of the base, and the safety cable rigging point in one unit

(see the illustration below). When mounting this fixture to truss be sure to secure an

appropriately rated clamp to the included omega bracket using a M10 screw fitted

through the center hole of the “omega bracket”. As an added safety measure be sure

to attached at least one properly rated safety cable to the fixture using on of the

safety cable rigging point integrated in the base assembly.

JNR DOT BEAM

.06.

②

① Omega Bracket

② Satety Clamp

③ Safety Cable

④ 1/4 Turn Quick-Lock Fasteners ①

③

④

1/4 Turn 1/4 Turn

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de PR Lighting

PR Lighting

PR Lighting XR480S BWS Manual de usuario

PR Lighting

PR Lighting MEGA COLOUR 2000 Manual de usuario

PR Lighting

PR Lighting XPar 336-W Manual de usuario

PR Lighting

PR Lighting PR-8330 Manual de usuario

PR Lighting

PR Lighting XR480 BWS Manual de usuario

PR Lighting

PR Lighting JNR PAR COB Manual de usuario

PR Lighting

PR Lighting XLED 6007 Manual de usuario

PR Lighting

PR Lighting XR 1700 FRAMING Manual de usuario

PR Lighting

PR Lighting XR480 BEAM Manual de usuario

PR Lighting

PR Lighting XLED 250 BEAM Manual de usuario

PR Lighting

PR Lighting PR-8541 Manual de usuario

PR Lighting

PR Lighting JUNIOR JNR PAR ZOOM 3618 Manual de usuario

PR Lighting

PR Lighting PR-8242 Manual de usuario

PR Lighting

PR Lighting XR440 BEAM Manual de usuario

PR Lighting

PR Lighting XLED 3007 Manual de usuario

PR Lighting

PR Lighting PR-8802 Manual de usuario

PR Lighting

PR Lighting XRLED 1200 SPOT Manual de usuario

PR Lighting

PR Lighting XLED 6019 Manual de usuario

PR Lighting

PR Lighting PR-6000 Spot Manual de usuario

PR Lighting

PR Lighting PR-2302 Manual de usuario

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Manual de usuario

PR Lighting

PR Lighting AQUA LED 600 SPOT Manual de usuario

PR Lighting

PR Lighting LED Studio 3201D Manual de usuario

PR Lighting

PR Lighting XLED 1037 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario