PR Lighting MEGA COLOUR 2000 Manual de usuario

MEGA COLOUR 2000

PR-4200

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/18

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

STAND-ALONE MODE 7

MASTER/SLAVE MODE 7

LED INDICATION 7

OPERATION MENU 8

DMX PROTOCOL 12

MAINTENANCE 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 13

TECHNICAL DATA 14

ELECTRICAL DIAGRAM 16

COMPONENT ORDER CODES 17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

XLR cable 1 Pc 3-pin plug

Mounting board 1 Pc

Screws 6 Pcs

M10×25

G clamps 2 Pcs

Safety cord 2 Pcs

This manual 1 Pc

Ωclamps 2 Pcs Options

3/18

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 10m. 10m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

Never run the projector without a lamp.

During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that

the device is defective.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/18

INSTALL THE PROJECTOR

2PCS

Front cover

Power supply

Handle

Control panel

Clamp

Safety cord

Power switch

DMX connection

Lock screw for tilt

Safety cord connection

The unit was designed to make installation easy: it can be fitted on a floor or ceiling as required.

Take mounting board and 2 safety cords out from the package and mount the mounting board on the underside of fixture

with 6 screws. Then mount 2 clamps on the underside of mounting board with 4 retainers. Hang the fixture on the

structure and fasten the screws attached to each clamp. WARNING: To pass 2 SAFETY CORDS through 2 HOLES

for safety! Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always

ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of

MEGA COLOUR 2000.

WARNING:

1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

3. For safety the safety cord should afford 10 times of the unit’s weight.

FITTING THE LAMP

M10 nut

Front cover

Lamp

Protection plate

for lamp

Fan group Back cover

M10 nut

Lock the tilt before changing the lamp.

Remove the front cover and back cover by undoing the 16 lock catches and 8xM4 screws.

Undo fan group by undoing 6 screws.

Remove the protection plate of lamp by undoing the 3xM4 screws.

Do not change new lamp until old lamp has cooled.

Undo the 2xM10 screws from double ends of the lamp and then pull out the old lamp toward lamp cap.

Insert the new lamp in the lamp-holder, and ensure the little bubble on the lamp is at a right angle (90°) to the beam path.

Keep the lamp clean during installation.

Reinstall all the components before removing by retighten the screws.

5/18

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

FUNCTION

DMX IN

DMX OUT

GND

DATA +

DATA -

DMX512

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) XLR plug and socket. The XLR's are connected as shown in the

figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. MEGA COLOUR 2000 accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

DMX IN DMX OUT

DMX IN FROM

CONTROLLER

TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

No.1 No.2 No.3

6/18

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via pressbutton switch and LED display. Turn the projector on and the

LED display will show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu.

Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you do not, the system will display DMX start address

after 60 seconds automatically.

TO SET THE DMX START ADDRESS

Each MEGA COLOUR 2000 must be given a DMX start address so that the correct projector responds to the correct

control signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital

control information being sent out from the controller. The MEGA COLOUR 2000 has 2 DMX modes. There are

standard mode and short mode. For example standard mode has 13 channels, so set the No. 1 projector’s address 001,

No. 2 projector’s address 014, No. 3 projector’s address 027, No. 4 projector’s address 040, and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button FUNC to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm.

The DMX start address can be set discretionarily under the STAND-ALONE control mode. It is recommended that the

DMX start address must be set correctly so that the unit may be individually switched on and off when multi-projectors

controlled by controller.

7/18

STAND-ALONE MODE

To operate the projector without connecting a controller, setup options master mode disabled, the projector

will run in Stand-Alone mode automatically.

MASTER/SLAVE MODE

Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them

with each other. Select one projector as the master with setting options master mode enabled but slaves.

Regard the other projectors as the slaves with setting options slave mode enabled and all DMX start

address “001”.

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

DMX IN DMX OUT

TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

MASTER SLAVE SLAVE

LED INDICATION

On DMX signal OK

Off No DMX signal

Green

Flash DMX signal error

Yellow On

Setting the panel

Blue On Power

Red Running Slave mode or self test mode

Red/Green Green Running Master mode

8/18

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL

PR LIGHTING

MEGA

COLOUR

2000

DMX

Address=001

PR LIGHTING

DMX Address

PR LIGHTING

DMX Address

PR LIGHTING

Reset

PR LIGHTING

Reset

Are You Sure?

PR LIGHTING

DMX Mode

Standard 16

PR LIGHTING

DMX Mode PR LIGHTING

DMX Mode

Short 8

PR LIGHTING

Lamp Control By

Control Channel

PR LIGHTING

Lamp Control By

Power On

PR LIGHTING

Config Settings

PR LIGHTING

Lamp Control

PR LIGHTING

Lamp Control By

DMX Present

PR LIGHTING

Pan DMX Invert

OFF

PR LIGHTING

Pan DMX Invert PR LIGHTING

Pan DMX Invert

PR LIGHTING

Tilt DMX Invert

OFF

PR LIGHTING

Tilt DMX Invert PR LIGHTING

Tilt DMX Invert

PR LIGHTING

Pan Tilt Swap

OFF

PR LIGHTING

Pan Tilt Swap PR LIGHTING

Pan Tilt Swap

PR LIGHTING

Defaults

OFF

PR LIGHTING

Option

Settings

PR LIGHTING

Defaults PR LIGHTING

Defaults

Restore Defaults

PR LIGHTING

Display

On Always

PR LIGHTING

Display Mode PR LIGHTING

Display

Off After Delay

PR LIGHTING

Disp Dim Level

Full

PR LIGHTING

Display

Options

PR LIGHTING

Display Dimming

PR LIGHTING

Disp Dim Level

9/18

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

PR LIGHTING

Disp Dim Level

Min

PR LIGHTING

Display Contrast

PR LIGHTING

Display Contrast

XXX(1~36, Default

is 16)

PR LIGHTING

Lamp Hours

PR LIGHTING

Lamp Hours =

PR LIGHTING

Reset Lamp Hours

Are You Sure?

PR LIGHTING

Total Hours

PR LIGHTING

Total Hours =

PR LIGHTING

Display Board

PR LIGHTING

Display Board =

XX℃

PR LIGHTING

Driver Board 1

PR LIGHTING

Driver Board 1 =

XX ℃

PR LIGHTING

Temperature

PR LIGHTING

Pan and Tilt

PR LIGHTING

Pan and Tilt =

XX ℃

PR LIGHTING

Display Board

PR LIGHTING

Display Board =

X.X.X

PR LIGHTING

Driver Board 1

PR LIGHTING

Driver Board 1 =

X.X.X

PR LIGHTING

Pan and Tilt

PR LIGHTING

Pan and Tilt =

X.X.X

PR LIGHTING

Information

PR LIGHTING

Software Version

PR LIGHTING

Power Board

PR LIGHTING

Power Board =

X.X.X

Factory Setup Off

Test Mod e s

Factory Setup Factory Setup On

Self Test Off

PR LIGHTING

Test Mod e s Test Mod e s

Self Test Self Test On

PR LIGHTING

Lamp Manual

Control

Lamp Status

Status =

Control=

10/18

PR LIGHTING

Turn Lamp On

PR LIGHTING

Turn Lamp Off

Mode=

DMX512

Select Memory

User Memory 1

Select Memory

User Memory 2

Select Memory

Preset Memory 1

Select Memory

Preset Memory 2

Mode =

Master mode

Select Memory

Preset Memory 3

Select Memory

User Memory 1

Select Memory

User Memory 2

Select Memory

Preset Memory 1

Select Memory

Preset Memory 2

Mode =

Slave mode

Select Memory

Preset Memory 3

PR LIGHTING

Operation

Mode

Mode =

Static Scene

Cyan Cyan

XXX

Yellow Yellow

XXX

Magenta Magenta

XXX

Focus Focus

XXX

Frost Frost

XXX

Dimmer Dimmer

XXX

Strobe Strobe

XXX

Pan High Pan High

XXX

Pan Low Pan Low

XXX

Tilt High Tilt High

XXX

Tilt Low Tilt Low

XXX

M-S peed M-Speed

XXX

Delay

XX Seconds

（0.25s~100min）

User Memory1 Scene XX

Link To Step Link To Step

XXX (1~32）

User Memory Edit User Memory

User Memory 2 Scene XX

（1~32）Dimmer Dimmer

XXX

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de PR Lighting

PR Lighting

PR Lighting PR-8330 Manual de usuario

PR Lighting

PR Lighting OMEGA Manual de usuario

PR Lighting

PR Lighting XR480S BWS Manual de usuario

PR Lighting

PR Lighting XRLED 3000-W Framing Manual de usuario

PR Lighting

PR Lighting PR-8242 Manual de usuario

PR Lighting

PR Lighting PR-8102 Manual de usuario

PR Lighting

PR Lighting JUNIOR JNR-8146C Manual de usuario

PR Lighting

PR Lighting LED Studio 3800T Manual de usuario

PR Lighting

PR Lighting XR 380 Beam Manual de usuario

PR Lighting

PR Lighting JNR PAR COB Manual de usuario

PR Lighting

PR Lighting XRLED 300 SPOT Manual de usuario

PR Lighting

PR Lighting PR-2302 Manual de usuario

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Manual de usuario

PR Lighting

PR Lighting LED STUDIO 3605 Manual de usuario

PR Lighting

PR Lighting XR440 BEAM Manual de usuario

PR Lighting

PR Lighting XLED 6019 Manual de usuario

PR Lighting

PR Lighting CSL 1037 Manual de usuario

PR Lighting

PR Lighting ARC LED 3108 Manual de usuario

PR Lighting

PR Lighting XL 1200 Manual de usuario

PR Lighting

PR Lighting XR-230 BEAM Manual de usuario

PR Lighting

PR Lighting JNR BWS 350 Manual de usuario

PR Lighting

PR Lighting SOLO 575 Manual de usuario

PR Lighting

PR Lighting ARC LED 1054 Manual de usuario

PR Lighting

PR Lighting XR 1000 Framing Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario