Planet WGSW-52040 Manual de usuario
L2+ 48-Port 10/100/1000BASE-T + 4-Port 1000X SFP
Managed Gigabit Switch
WGSW-52040
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Switch Management.................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 8
6. ConguringIPAddress................................................................................ 9
7. Starting Web Management .........................................................................11
8. SavingtheConguration ............................................................................13
9. LogintheManagedSwitch..........................................................................14
10. Customer Support.....................................................................................16
3
1. Package Contents
Thanks you for purchasing PLANET L2+ 48-Port 10/100/1000BASE-T + 4-Port
1000X SFP Managed Gigabit Switch, WGSW-52040. “Managed Switch” is also
usedtorefertotheWGSW-52040inthisquickinstallationguide.
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
TheManagedSwitchx1
QuickInstallationGuidex1
RJ45-to-DB9ConsoleCablex1
PowerCordx1
Rubber Feet x 4
TwoRack-mountingBracketswithAttachmentScrewsx1
SFPDustCapx4
If any item is found missing or damaged, please contact your local reseller for
replacement
4
2. Switch Management
To set up the Managed Switch, the user needs to congure the Managed Switch
fornetwork management.The ManagedSwitchprovides twomanagement options:
Out-of-BandManagementandIn-BandManagement.
Out-of-Band Management
Out-of-band management is the management through Console interface.
Generally, the user will use out-of-band management for the initial switch
conguration,orwhenin-bandmanagementisnotavailable.
IMPORTANT!
The Managed Switch is shipped without IP address assigned by
default. User must assign an IP address to the Managed Switch via
the Console interface to be able to remotely access the Managed
Switch through Telnet or HTTP.
In-Band Management
In-band management refers to the management by logging in to the Managed
Switchusing Telnetor HTTP,orusing SNMPmanagement softwaretocongure the
Managed Switch. In-band management enables the management of the Managed
SwitchtoattachsomedevicestotheSwitch.Thefollowingproceduresarerequired
toenableIn-bandmanagement:
1. Logon to console
2.Assign/CongureIPaddress
3. Create a remote login account
4.EnableHTTPorTelnetserverontheManagedSwitch
In case in-band management fails due to Managed Switch conguration changes,
out-of-band management can be used for conguring and managing the Managed
Switch.
5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS-232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.
6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
consoleportdirectlythroughPCwithouttheneedofNullModem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS-232 to RJ45 Cable
Console Port
RJ-45
Figure 4-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Windows' Hyper Terminal program may be a good choice. The Hyper
TerminalcanbeaccessedfromtheStartmenu.
1. Click STARTmenu,thenPrograms, AccessoriesandthenHyper Terminal.
2.TypeanameforopeningHyperTerminal,suchas“COM1_9600”.
3.When the following screen appears, make sure that the COM port should be
conguredas:
Baud :9600
Parity :None
Databits :8
Stop bits : 1
Flowcontrol :None
Figure 4-2 Hyper Terminal COM Port Conguration
7
5. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
theterminalwilldisplay“runningtestingprocedures”.
Then, the following message asks the login user name and password. The factory
default user name and password are as follows as the login screen in Figure 5-1
appears.
Username:admin
Password:admin
Figure 5-1 Managed Switch Console Login Screen
The user can now enter commands to manage the Switch. For a detailed
descriptionforthecommands,pleaserefertothefollowingchapters.
Note
1. For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
8
6.ConguringIPAddress
The IP address conguration commands for VLAN1 interface are listed below.
Before using in-band management, the Managed Switch must be congured with
an IP address by out-of-band management (i.e. console mode). The conguration
commands are as follows (All switch conguration prompts are assumed to be
“WGSW-52040”hereafterifnototherwisespecied):
WGSW-52040>enable
WGSW-52040#cong
WGSW-52040(cong)#interface vlan 1
WGSW-52040(Cong-if-Vlan1)#ip address 192.168.1.254 255.255.255.0
ThepreviouscommandwouldapplythefollowsettingsfortheManagedSwitch.
IPv4Address:192.168.1.254
Subnet Mask: 255.255.255.0
Figure 6-1 Conguring IPv4 Address Screen
To check the current IP address or modify a new IP address for the Managed
Switch,pleaseusetheproceduresasfollows:
9
Show the current IP address
1. On “WGSW-52040#”prompt,enter“show ip interface brief”.
2.Thescreen displaysthecurrent IPaddress,Subnet Mask andGatewayasshown
inFigure6-2.
Figure 6-2 Showing IP information Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Managed Switch
throughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter,enter“help”anytimeinconsoletogetthehelpdescription.
10
7. Starting Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer,MozillaFirefox,GoogleChromeorAppleSafari.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 7-1 IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch. Please note the Managed Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set on the same IP
subnet address.
For example, the IP address of the Managed Switch is congured with
192.168.1.254, then the manager PC should be set at 192.168.1.x (where x
is a number between 1 and 253, except 254), and the default subnet mask is
255.255.255.0.
Thefactorydefaultusernameandpasswordareasfollows:
Username:admin
Password:admin
Otros manuales para WGSW-52040
1
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet GSW-1602SF Manual de usuario
Planet
Planet MGS-5220-8P2X Manual de usuario
Planet
Planet IGS-20160HPT Manual de usuario
Planet
Planet FSD-808P Manual de usuario
Planet
Planet GSD-1022UP Manual de usuario
Planet
Planet FSD-504HP Manual de usuario
Planet
Planet HPOE-460 Manual de usuario
Planet
Planet GSD-1603 Manual de usuario
Planet
Planet GSW-1820HP Manual de usuario
Planet
Planet IGS-10020M Manual de usuario
Planet
Planet FSD-503 Manual de usuario
Planet
Planet POE-400 Manual de usuario
Planet
Planet WGSD-10020 Instrucciones de instalación
Planet
Planet WGSW-14020 Manual de usuario
Planet
Planet FSD-504HP Manual de usuario
Planet
Planet GSD-801 Manual de usuario
Planet
Planet GSD-808HP Manual de usuario
Planet
Planet FGSW-2022VHP Manual de usuario
Planet
Planet XGSW-28040HP Manual de usuario
Planet
Planet WGSD-910 Manual de usuario
