Planet GS-5220-8P2T2S Manual de usuario
L2+ Gigabit Ethernet Switch
GS-5220-8P2T2S
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
3.1 Logging on to Console ......................................................................... 6
3.2 ConguringIPAddress......................................................................... 7
3.3 StoringCurrentSwitchConguration..................................................... 9
4. Starting Web Management .........................................................................10
4.1 LoggingontotheL2+ManagedPoE+Switch.......................................11
4.2 SavingConguration...........................................................................13
5. RecoveringBacktoDefaultConguration.....................................................14
6. Customer Support ....................................................................................15
3
1. Package Contents
Thank you for purchasing PLANET L2+ 8-Port 10/100/1000T 802.3at PoE + 2-Port
10/100/1000T + 2-Port 100/1000X SFP Managed Switch, GS-5220-8P2T2S. “L2+
Managed PoE+ Switch” mentioned in this quick installation guide refers to the
GS-5220-8P2T2S.
Open the box of the L2+ Managed PoE+ Switch and carefully unpack it. The
boxshouldcontainthefollowingitems:
L2+ManagedPoE Switch x 1 QuickInstallation
Guidex1 Rack-mountingKits
RubberFeetx1set ACPowerCordx1 DB9 to RS232
Cable x 1 SFPDustCapx2
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows XP/2003/2008/2012/Vista/7/8/10, MAC OS X or
later,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheL2+ManagedPoE+Switch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
TheabovePCisinstalledwithWebbrowser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the L2+ Managed PoE+ Switch. If the Web interface of the L2+
Managed PoE+ Switch is not accessible, please turn off the anti-
virussoftwareorfirewallandthentryitagain.
5
3. Terminal Setup
Tocongure the system,connectaserial cabletoaCOMport onaPCornotebook
computerandtoDB9typeofserialportoftheL2+ManagedPoE+Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: L2+ Managed PoE+ Switch Console Connectivity
A terminal program, such as Tera Term or PuTTY, is required to make the software
connectiontotheL2+ManagedPoE+Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zDatabits:8
zParity:None
zStopbits:1
zFlowcontrol:None
Figure 3-2: COM Port Conguration
6
3.1 Logging on to Console
Once the terminal is connected to the device, power on the L2+ Managed PoE+
Switch and the terminal will display “running testing procedures”. Then, the
following message asks to log in user name and password. The factory default
user name and password are shown as follows and the login screen in Figure 3-3
appears.
Username:admin
Password:admin
Figure 3-3: L2+ Managed PoE+ Switch Console Login Screen
Theuser can nowenter commands tomanage the L2+Managed PoE+Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1. For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
7
3.2 ConguringIPAddress
TheL2+ManagedPoE+SwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the L2+ Managed
PoE+Switch,pleaseusetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.
Figure 3-4: IP Information Screen
8
Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure3-5.
GS-5220-8P2T2S#congureterminal
GS-5220-8P2T2S(cong)#interfacevlan1
GS-5220-8P2T2S(cong-if-vlan)#ipaddress192.168.1.100255.255.255.0
Figure 3-5: Conguring IP Address Screen
The previous command would apply the following settings for the L2+ Managed
PoE+Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
4.Repeatstep1tocheckiftheIPaddresshaschanged.
If the IP is successfully congured, the L2+ Managed PoE+ Switch will apply the
new IP address setting immediately. You can access the Web interface of the L2+
ManagedPoE+SwitchthroughthenewIPaddress.
9
3.3 StoringCurrentSwitchConguration
In the L2+ Managed PoE+ Switch, the running conguration sequence running-
cong can be saved from the RAM to FLASH by “copy” command, so that the
running conguration sequence becomes the start-up conguration le, which is
calledcongurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 3-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.
10
4. Starting Web Management
The following shows how to start up the Web Management of the L2+ Managed
PoE+ Switch. Note the L2+ Managed PoE+ Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the L2+ Managed PoE+ Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 4-1: IP Management Diagram
Otros manuales para GS-5220-8P2T2S
1
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet FSP-804P Manual de usuario
Planet
Planet FSD-804PS Manual de usuario
Planet
Planet FNSW-1601 Manual de usuario
Planet
Planet FSD-Series Manual de usuario
Planet
Planet WSW-2620 Manual de usuario
Planet
Planet GSD-1022UP Manual de usuario
Planet
Planet GSD-800S Manual de usuario
Planet
Planet VC-810S Manual de usuario
Planet
Planet IPM-4220 Manual de usuario
Planet
Planet XGSW-28040 Manual de usuario
Planet
Planet IGS-1020PTF Series Manual de usuario
Planet
Planet FNSW-1601 Manual de usuario
Planet
Planet IGS-5225-4T2S Manual de usuario
Planet
Planet FSD-808HP Manual de usuario
Planet
Planet Palm-Top EH-501 Manual de usuario
Planet
Planet IGS-5227X-4P2T Manual de usuario
Planet
Planet GSD-1020 Manual de usuario
Planet
Planet WGS-5225-8MT Manual de usuario
Planet
Planet KVM-210 Series Manual de usuario
Planet
Planet IGS-4215-4P4Tv2 Manual de usuario
