Planet IGS-4215-16P2T2S Manual de usuario
Industrial L2/L4 Managed Gigabit Switch
with 4-/8-/16-Port 802.3at PoE+
IGS-4215-4P4T/IGS-4215-4P4T2S
IGS-4215-8P2T2S/IGS-4215-16P2T2S
Industrial L2/L4 Managed Gigabit Switch
with 4-/8-Port 802.3bt PoE++
IGS-4215-4UP4T2S/IGS-4215-8UP2T2S
Quick Installation Guide
Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 4
3. Wiring the Power Inputs ....................................................................... 5
3.1 Grounding the Device..................................................................... 7
4. Terminal Setup..................................................................................... 8
4.1 Logging on to the Console.............................................................. 9
4.2 ConguringIPAddressviaConsole ............................................... 10
4.3 StoringCurrentSwitchConguration ............................................. 11
5. Sarting Web Management ................................................................... 12
5.1 Logging in to the Industrial Managed PoE+ Switch ......................... 12
5.2 SavingCongurationviaWeb ....................................................... 14
6. RecoveringBacktoDefaultConguration ............................................. 15
7. Customer Support .............................................................................. 16
3
1. Package Contents
Thank you for purchasing PLANET L2/L4 Managed Gigabit Switch. The
descriptions of these models are shown below:
IGS-4215-4P4T Industrial4-Port10/100/1000T802.3atPoE+4-Port
10/100/1000TManagedSwitch
IGS-4215-4P4T2S Industrial4-Port10/100/1000T802.3atPoE+4-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-4215-8P2T2S Industrial8-Port10/100/1000T802.3atPoE+2-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-4215-16P2T2S Industrial16-Port10/100/1000T802.3atPoE+2-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-4215-4UP4T2S Industrial4-Port10/100/1000T802.3btPoE+4-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-4215-8UP2T2S Industrial8-Port10/100/1000T802.3btPoE+2-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
“Industrial Managed PoE+ Switch” is used as an alternative name in this
Quick Installation Guide.
Open the box of the Industrial Managed PoE+ Switch and carefully unpack it.
The box should contain the following items:
zThe Industrial Managed PoE+ Switch x 1
zQuick Installation Guide Sheet x 1
zRS232 to RJ45 Console Cable x 1
zDust Caps
Model RJ45 Dust Caps SFPDustCaps
IGS-4215-4P4T 9 -
IGS-4215-4P4T2S 9 2
IGS-4215-8P2T2S 11 2
IGS-4215-16P2T2S 19 2
IGS-4215-4UP4T2S 9 2
IGS-4215-8UP2T2S 11 2
zDIN-railKitx1
zWallMountingKitx1
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
Workstations running Windows XP/2003/Vista/7/8/10/2008/10/11, MAC OS
Xorlater,Linux,UNIX,orotherplatformsarecompatiblewith TCP/IPproto-
cols.
WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
Serial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator,
such as Tera Term, PuTTY or Hyper Terminal included in Windows
XP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the
other ends to the RJ45 console port of the Industrial Managed PoE+
Switch.
Ethernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connec-
tors.
The above PC is installed with Web browser.
It is recommended to use Google Chrome (version
116.0.5845.188) or above to access the Industrial Managed
PoE+ Switch. If the Web interface of the Industrial Managed
PoE+ Switch is not accessible, please turn off the anti-virus soft-
ware or firewall and then try it again.
5
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed PoE+ Switch indicates a DC inlet
power socket and consists of one terminal block connector within 6 contacts.
Please follow the steps below to insert the power wire.
1.Insert positive/negative DC power wires into contacts 1 and 2 for Power 1
or 5 and 6 for Power 2.
V1+ V2+
PWR1 PWR2Alarm
DC Input:
48-54V
, 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Figure 3-1: IGS-4215-4P4T/IGS-4215-4P4T2S/IGS-4215-8P2T2S DC Inlet Power Socket
DC Input:
48-54V , 8.5A max.
Max. Fault Alarm Loading: 24V, 1A
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-2: IGS-4215-4UP4T2S/IGS-4215-8UP2T2S DC Inlet Power Socket
DI
0DI
1DO
0DO
1GND GND
Alarm
V1+ V2+
PWR2PWR1
Dual power input is required for
maximum PoE loading.
Refer to user’s manual for more details.
Input: 48-54V , 7.5A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-3: IGS-4215-16P2T2S DC Inlet Power Socket
6
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
V1+ V1- V2+ V2-
Power 1 Power 2
Figure 3-4: Power 1 & 2 Pins of Terminal Block Connector
Item Positive(+)Pin Negative(-)Pin
IGS-4215 Series Pin1/5 Pin2/6
1. The wire gauge for the terminal block should be in the range
from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connectingPLANETIndustrialManagedPoE+Switch.
PWR1 and PWR2 must provide exactly the same DC voltage
for power load balance while operating with dual power input.
7
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
V1+ V2+
PWR1 PWR2Alarm
DC Input:
48-54V
, 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Earth Ground
Figure 3-5: Grounding Method (applies to all models)
8
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to the RJ45 type of the console port of the Industrial
Managed PoE+ Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed PoE+ Switch Console Connectivity
A terminal program is required to make the software connection to the
Industrial Managed PoE+ Switch.
1. Run terminal program on the OS.
2. When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Data bits: 8
Parity:None
Stop bits: 1
Flowcontrol:None
Figure 4-2: COM Port Conguration
9
4.1 Logging on to the Console
Once the terminal is connected to the device, power on the Industrial Managed
PoE+ Switch and the terminal will display “running testing procedures”. Then,
the following message asks to log in user name and password. The factory
default user name and password are shown as follows, and the login screen in
Figure4-3appears.
The following console screen is based on the IGS-4215-8P2T2S.
The display of the other IGS-4215 PoE Series is the same as
that of the IGS-4215-8P2T2S.
Username: admin
Password: admin
Figure 4-3: Industrial Managed PoE+ Switch Console Login Screen
The user can now enter commands to manage the Industrial Managed PoE+
Switch. For a detailed description of the commands, please refer to the
following chapters.
1.For security reason, please change and memorize the new
password after this first setup.
2. Only accept command in lowercase letter under console inter-
face.
10
4.2 ConguringIPAddressviaConsole
The Industrial Managed PoE+ Switch is shipped with default IP address as
follows:
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Industrial
Managed PoE+ Switch, please use the procedures as follows:
Show the current IP address
1.Atthe“IGS-4215-8P2T2S#” prompt, enter “show ip”.
2. The screen displays the current IP address, subnet mask and gateway as
showninFigure4-4.
Figure 4-4: IP Information Screen
CongurationoftheIPAddress
3.Atthe“IGS-4215-8P2T2S #” prompt, enter “congure”.
4.At the “IGS-4215-8P2T2S (cong)#” prompt, enter the following
command and press <Enter>asshowninFigure4-5.
IGS-4215-8P2T2S(cong)#ip address 192.168.1.100 mask 255.255.255.0
IGS-4215-8P2T2S(cong)#ip default-gateway 192.168.1.254
The previous command would apply the following settings for the Industrial
Managed PoE+ Switch.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet IPM-8221 Manual de usuario
Planet
Planet IGS-1020PTF Series Manual de usuario
Planet
Planet IGS-5225-4T2S Manual de usuario
Planet
Planet GSD-1020S Manual de usuario
Planet
Planet GSW-1601 Manual de usuario
Planet
Planet FGSW-2402RS Manual de usuario
Planet
Planet GSW-1601 Manual de usuario
Planet
Planet NOVASwitch FNSW-8086F Manual de usuario
Planet
Planet XGSW-28040HP Manual de usuario
Planet
Planet DSP-1000 Manual de usuario
Planet
Planet XGS-6311 Series Manual de usuario
Planet
Planet SGSW-4802 Manual de usuario
Planet
Planet GSD-504 Manual de usuario
Planet
Planet GSD-808HP Manual de usuario
Planet
Planet FSD-504HP Manual de usuario
Planet
Planet WGSD-8020P Manual de usuario
Planet
Planet IGS-1020TF Manual de usuario
Planet
Planet WS-1032P Manual de usuario
Planet
Planet FSP-804P Manual de usuario
Planet
Planet IKVM-8010 Manual de usuario
