Planet IGS-1020TF Manual de usuario

Industrial 8-Port 10/100/1000BASE-T

+ 2-Port 100/1000BASE-X SFP Ethernet Switch

IGS-1020TF

User’s Manual

Table Of Contents

1. Package Contents ............................................................. 3

2. Hardware Introduction ...................................................... 4

2.1 Physical Dimensions ................................................ 4

2.2 Switch Front Panel................................................... 5

2.3 LED Indicators ........................................................ 6

2.4 Switch Upper Panel ................................................. 8

2.5 Wiring the Power Inputs .......................................... 8

2.6 Wiring the Fault Alarm Contact ............................... 10

2.7 ProductSpecications ............................................ 10

3. Installation..................................................................... 14

3.1 DIN-rail Mounting Installation ................................. 14

3.2 Wall-mount Plate Mounting..................................... 16

3.3 Installing the SFP Transceiver ................................. 17

3.4 Removing the Transceiver Module ........................... 19

4. Troubleshooting .............................................................. 20

APPENDIX A: Networking Connection.................................... 21

A.1 Switch’s RJ45 Pin Assignments................................... 21

A.2 RJ45 Cable Pin Assignments ...................................... 22

A.3 Fiber Optic Cable Connection Parameter ..................... 23

APPENDIX B: Approved PLANET SFP Transceivers .................. 25

1.Package Contents

Thank you for purchasing PLANET industrial 10-port Gigabit

Ethernet Switch, IGS-1020TF. In the following section, the term

“Industrial Gigabit Ethernet Switch” means the IGS-1020TF.

Open the box of the Industrial Gigabit Ethernet Switch and

carefully unpack it. The box should contain the following items:

Industrial Gigabit Ethernet Switch x 1 User’s Manual x 1

Wall-mount Kit x DIN Rail Kit x 1

If any of these are missing or damaged, please contact your

dealer immediately; if possible, retain the carton including the

original packing material, and use them again to repack the

product in case there is a need to return it to us for repair.

2.Hardware Introduction

2.1 Physical Dimensions

IGS-1020TF Industrial Gigabit Ethernet Switch dimensions (W

x D x H): 135 x 87.8 x 50mm

Side View

Bottom View Front View

Mounting Kit

DIN-Rail Kit

Dimensions ( unit = mm )

Top View Rear View

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

100/1000X SFP

109

P1 P2 FAULT

9 10

IGS-1020TF

ACT

1000 LNK

LNK

10/100

100

ACT

1000

LNK

2.2 Switch Front Panel

The front panel of the Industrial Gigabit Ethernet Switch consists

of 8 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports and

2 dual speed 100/1000BASE-X SFP slots. The LED Indicators

are also located on the RJ45 ports and SFP slots of the Gigabit

Ethernet Switch.

Figure 2-1 shows the front panel of Industrial Gigabit Ethernet

Switch.

100/1000X SFP

109

P1 P2 FAULT

9 10

IGS-1020TF

ACT

1000 LNK

LNK

10/100

100

ACT

1000

LNK

Figure 2-1: IGS-1020TF Front Panel

Gigabit TP Interface

10/100/1000BASE-T Copper, RJ45 Twisted-pair: Up to 100

meters.

SFP Slot

100/1000BASE-X mini-GBIC slot, SFP (Small-form Factor

Pluggable) transceiver module: From 550 meters to 2km

(multi-mode ber) and 10/20/30/40/50/70/120 kilometers

(single-modeber).

2.3 LED Indicators

System

LED Color Function

P1 Green Lit: indicates power 1 has power.

P2 Green Lit: indicates power 2 has power.

FAULT Red Lit: indicates either power 1 or power 2 has

no power.

Per 10/100/1000T Port

LED Color Function

100

LNK/ACT Orange

Lit: indicates the link through that port is

successfully established at 100Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 1000Mbps.

1000

LNK/ACT Green

Lit: indicates the link through that port is

successfully established at 1000Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 100Mbps.

Per 100 / 1000X SFP Slot

LED Color Function

100

LNK/ACT Orange

Lit: indicates the link through that port is

successfully established at 100Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 1000Mbps.

1000

LNK/ACT Green

Lit: indicates the link through that port is

successfully established at 1000Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 100Mbps.

2.4 Switch Upper Panel

The upper panel of the Industrial Gigabit Ethernet Switch

consists of one terminal block connector within two DC power

inputs,

Figure 2-2 shows the upper panel of the Industrial Gigabit

Ethernet Switch.

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

Figure 2-2: Industrial Gigabit Ethernet Switch Upper Panel

2.5 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial Gigabit Ethernet Switch is used for two DC redundant

power inputs. Please follow the steps below to insert the power

wire.

When performing any of the procedures like

inserting the wires or tightening the wire-clamp

screws, make sure the power is OFF to prevent

from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1

and 2 for POWER 1, or 5 and 6 for POWER 2.

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

1. The wire gauge for the terminal block should be

in the range between 12 and 24 AWG.

2. The DC power input range is 12V ~ 48V DC.

2.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires, the

Industrial Gigabit Ethernet Switch will detect the fault status of

the power failure and then forms an open circuit. The following

illustration shows an application example for wiring the fault

alarm contacts.

123456

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be

in the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 30V, max. 3A

currents.

2.7 ProductSpecications

Model IGS-1020TF

HardwareSpecications

Copper Ports 8 x 10/100/1000BASE-T RJ45 TP

Auto-MDI/MDI-X, auto-negotiation

Tabla de contenidos

Otros manuales de Cambiar de Planet

Planet

Planet WGS-4215 Series Manual de usuario

Planet

Planet ISW-500 Manual de usuario

Planet

Planet IGS-10020M Manual de usuario

Planet

Planet KVM-U201 Manual de usuario

Planet

Planet GSW-1601 Manual de usuario

Planet

Planet GS-5220 Series Manual de usuario

Planet

Planet LRP-822CS Manual de usuario

Planet

Planet IGS-504HPT Manual de usuario

Planet

Planet FSD-1603 Manual de usuario

Planet

Planet IGS-5225-4T2S Manual de usuario

Planet

Planet POE-1200G Manual de usuario

Planet

Planet GSW-1601 Manual de usuario

Planet

Planet VC-820M Manual de usuario

Planet

Planet WSW-2401 Manual de usuario

Planet

Planet FGSW-2401 Manual de usuario

Planet

Planet KVM-800 Manual de usuario

Planet

Planet FSD-Series Manual de usuario

Planet

Planet GSW-1602SF Manual de usuario

Planet

Planet POE-151 Manual de usuario

Planet

Planet SGSD-1022 Manual de usuario

Planet

Planet IDL-2402 Manual de usuario

Planet

Planet NOVASwitch GSW-1200S Manual de usuario

Planet

Planet IGS-6325-16T4X Manual de usuario

Planet

Planet IPM-8221 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario