Planet GS-6320-8P2X Manual de usuario
L3 8-Port 10/100/1000T 802.3at PoE +
+ 2-Port 10G SFP+ Managed Switch
GS-6320-8P2X
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
3.1 Logging on to Console ......................................................................... 6
3.2 ConguringIPAddress......................................................................... 7
3.3 StoringCurrentSwitchConguration..................................................... 9
4. Starting Web Management .........................................................................10
4.1 LoggingintotheManagedPoESwitch .................................................10
4.2. SavingConguration...........................................................................13
5. RecoveringBacktoDefaultConguration.....................................................14
6. Customer Support .....................................................................................15
3
1. Package Contents
ThankyouforpurchasingPLANETManagedPoESwitch,GS-6320-8P2X.
“Managed PoE Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed PoE Switch and carefully unpack it. The box should
contain the following items:
zTheManagedPoESwitchx1
zQuickInstallationGuidex1
zRJ45 to RS232 Cable x 1
zRubber Feet x 4
zTwoRack-mountingBracketswithAttachmentScrewsx1
zPowerCordx1
zSFPDust-proofCapsx2
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows XP/2003/2008/2012/Vista/7/8/10, MAC OS X or
later,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
TheaboveWorkstationshavebeeninstalledwith terminal emulator, suchas
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable -- One end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedPoESwitch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
TheabovePCisinstalledwithWebbrowser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Managed PoE Switch. If the Web interface of the Managed PoE
Switch is not accessible, please turn off the anti-virus software or
firewallandthentryitagain.
5
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebookcomputerandtoRJ45typeofserialportoftheManagedPoESwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: Managed PoE Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
PoESwitch.PuttyorTeraTermmaybeagoodchoice.
1. Run terminal program Tera Term on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Speed:115200
Data:8bits
Parity:None
Stop bits: 1
Flowcontrol:None
Figure 3-2: COM Port Conguration
6
3.1 Logging on to Console
Once the terminal is connected to the device, power on the Managed PoE Switch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log in username and password. The factory default user name
andpasswordareshownasfollowsandtheloginscreeninFigure3-3appears
Username:admin
Password:admin
Figure 3-3: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed PoE Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Onlyacceptcommandinlowercaseletterunderconsoleinterface.
7
3.2 ConguringIPAddress
TheManagedPoESwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheprocedureasfollows:
Show the current IP Address
1.Atth“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.
Figure 3-4: IP Information Screen
8
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure3-5.
GS-6320-8P2X#congureterminal
GS-6320-8P2X(cong)#interface vlan 1
GS-6320-8P2X(cong-if-vlan)#ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the Managed PoE
Switch.
IPAddress:192.168.1.100
Subnet Mask: 255.255.255.0
Figure 3-5: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddresshaschanged
If the IP is successfully congured, the Managed PoE Switch will apply the new IP
addresssetting immediately. Youcanaccessthe Webinterfaceof theManaged PoE
SwitchthroughthenewIPaddress.
9
3.3 StoringCurrentSwitchConguration
In the Managed PoE Switch, the running conguration sequence running-cong
can be saved from the RAM to FLASH by “copy” command, so that the running
conguration sequence becomes the start-up conguration le, which is called
congurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
#copyrunning-congstartup-cong
Figure 3-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.
10
4. Starting Web Management
The following shows how to start up the Web Management of the Managed
PoE Switch. Note the Managed PoE Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
Forexample,thedefault IPaddressoftheManagedPoESwitchis192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 4-1: IP Management Diagram
4.1 Logging in to the Managed PoE Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
https://192.168.0.100 (the factory default IP address or the one that you
havejustchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure4-2appears.
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 4-2: Login Screen
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet SGS-5220-24T2X Manual de usuario
Planet
Planet GSW-1402S Manual de usuario
Planet
Planet FSD-804P Manual de usuario
Planet
Planet GSD-802S Manual de usuario
Planet
Planet WGSW-24000 Manual de usuario
Planet
Planet WGSW-5242 Manual de usuario
Planet
Planet POE-152 Manual de usuario
Planet
Planet GSW-1601 Manual de usuario
Planet
Planet IGS-10020PT Manual de usuario
Planet
Planet IGSW-2840 Manual de usuario
Planet
Planet VC-1602 Manual de usuario
Planet
Planet IGS-5225-4T2S Manual de usuario
Planet
Planet VC-810S Manual de usuario
Planet
Planet IGS-824UPT Manual de usuario
Planet
Planet GS-5220-24T4XVR Manual de usuario
Planet
Planet FSD-1600 Manual de usuario
Planet
Planet GSW-1600HP Manual de usuario
Planet
Planet GS-5220 Series Manual de usuario
Planet
Planet WGSW-20160HP Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
