Planet ISW-500T Manual de usuario
Industrial 5-/8-Port 10/100TX
Compact Ethernet Switch
ISW-500T/ISW-800T
User’s Manual
Table of Contents
1. Package Contents ............................................................. 3
2. Product Features............................................................... 4
3.ProductSpecications ....................................................... 5
4. Hardware Introduction ...................................................... 7
4.1 Three-View Diagram................................................... 7
4.2 Wiring the Power Inputs ........................................... 10
4.3 Wiring the Fault Alarm Contact.................................. 11
5. Installation..................................................................... 13
5.1 DIN-rail Mounting Installation.................................... 13
5.2 Wall-mount Plate Mounting ....................................... 15
Customer Support............................................................... 16
3
1.Package Contents
Thank you for purchasing PLANET industrial 5-/8-port 10/100TX
Compact Ethernet Switch, ISW-500T/800T. In the following
section, the term “Industrial Ethernet Switch” means the
ISW-500T or ISW-800T.
Open the box of the Industrial Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Ethernet Switch x 1 User’s Manual x 1
Wall-mount Kit DIN Rail Kit
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.
4
2.Product Features
Physical Port
5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function
(ISW-500T)
8-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function
(ISW-800T)
Layer 2 Features
Complies with IEEE 802.3 10BASE-T, IEEE 802.3u
100BASE-TX Ethernet standard
Supports auto-negotiation and 10/100Mbps half/full duplex
mode
Prevents packet loss with back pressure (half-duplex) and
IEEE802.3x pauseframeowcontrol(full-duplex)
Complieswith IEEE802.3azEnergyEfcientEthernet(EEE)
IEEE 802.1p CoS
Supports 1K MAC address
Automatic address learning and address aging
Industial Case & Installation
IP30 metal case
DIN rail and wall-mount design
12 to 48V DC, redundant power with polarity reverse
protect function
24V AC power input acceptable
Supports 6000 VDC Ethernet ESD protection
-40 to 75 degrees C operating temperature
Free fall, shock-proof and vibration-proof for industries
5
3.ProductSpecications
Product ISW-500T ISW-800T
HardwareSpecications
Copper Ports
5 10/100BASE-TX
RJ45 auto-MDI/MDI-X
ports
8 10/100BASE-TX
RJ45 auto-MDI/MDI-X
ports
Switch Architecture Store-and-Forward
Switch Fabric 1Gbps (non-blocking) 1.6Gbps
(non-blocking)
Throughput
(packet per second) 0.74Mpps@ 64 bytes 1.19Mpps@ 64 bytes
Address Table 1K entries, automatic source address
learning and aging
Shared Data Buffer 448K bits
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
ESD Protection 6KV DC
Enclosure IP30 metal case
Installation DIN rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power
input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm,
Pin 5/6 for Power 2
Alarm One relay output for power failure. Alarm
relay current carry ability: 1A @ 24V DC
LED Indicator
System:
Power 1 (Green) Power 2 (Green)
Fault Alarm (Red)
6
LED Indicator Per 10/100TX RJ45 Ports:
10/100 LNK/ACT (Green)
Dimensions
(W x D x H) 70 x 104 x 30 mm 70 x 115 x 41 mm
Weight 255g 300g
Power Requirements Dual 12~48V DC, 24V AC
Power Consumption Max. 2 watts/6.86BTU
(Ethernet full loading)
Max. 2.5
watts/8.57BTU
(Ethernet full loading)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
IEEE802.3x owcontrolandbackpressure
IEEE 802.1p Class of Service
IEEE802.3az EnergyEfcientEthernet(EEE)
Environment
Operating
Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
7
4.Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Industrial Ethernet Switch
consists of ve or eight auto-sensing 10/100/BASE-TX RJ45
port and one removable 6-pin terminal block. The LED
indicators are also located on the front panel.
18.00
9.00
91.00
52.00 52.00
104.00
30.00
50.00
30.00
70.00
21.69
28.65
Dimensions ( unit = mm )
Side View Front View Side View
Top View
Bottom View
Rear View
P1 P2 FAULT
ACT
LNK
10/100
1
2
3
4
5
ISW-500T
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
Figure 1: ISW-500T Three-View Diagram
8
115.00
41.00
70.00
18.00
3.50
103.00
5.50
30.00
50.00
28.65
27.19
Dimensions ( unit = mm )
Side View Front View Side View
Top View
Bottom View
Rear View
P1 P2 FAULT
ACTLNK
10/100
1
2
3
4
5
6
7
8
ISW-800T
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
Figure 2: ISW-800T Three-View Diagram
9
Front View
P1 P2 FAULT
ACT
LNK
10/100
1
2
3
4
5
ISW-500T
P1 P2 FAULT
ACTLNK
10/100
1
2
3
4
5
6
7
8
ISW-800T
Figure 1: ISW-500T Front View Figure 2: ISW-800T Front View
LED Denition:
System
LED Color Function
DC1 Green Lights to indicate DC power input 1 has power.
DC2 Green Lights to indicate DC power input 2 has power.
Fault Red Lights to indicate that AC or DC power has failed.
Per 10/100BASE-TX Port
LED Color Function
10/100
LNK/
ACT
Green
Lights Indicating the port is running at 10/100Mbps
speed and successfully established.
Blinks Indicating that the switch is actively sending
or receiving data over that port.
10
Top View
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
1 2 3 4 5 6
Figure 1: ISW-500T Top View
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
1 2 3 4 5 6
Figure 2: ISW-800T Top View
4.2 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Ethernet Switch is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Enrutador de red de Planet
Planet
Planet VC-230 Manual de usuario
Planet
Planet ADE-3400v4 Manual de usuario
Planet
Planet WBS-900AC-KIT Manual de usuario
Planet
Planet WGS3-2820 Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
Planet
Planet XRT-401F Manual de usuario
Planet
Planet WGSD-10020 Manual de usuario
Planet
Planet XRT-401B Manual de usuario
Planet
Planet WNAP-7335 Manual de usuario
Planet
Planet FGSW-1820RS Manual de usuario
Planet
Planet FWA-2100-NR Manual de usuario
Planet
Planet GS-4210-24P2S Manual de usuario
Planet
Planet WSD-800 Manual de usuario
Planet
Planet XRT-401C Manual de usuario
Planet
Planet WGS3-2840 Manual de usuario
Planet
Planet AND-4102 Manual de usuario
Planet
Planet WGSW-2620HP Manual de usuario
Planet
Planet WGSW-404 Manual de usuario
Planet
Planet ADSL 2/2+ VPN Firewall Router ADW-4302A v2 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad