Planet IPOE-E202 Manual de usuario
Industrial 1-port 802.3at PoE+ to 2-port 802.3af
PoE Extender
IPOE-E202
User’s Manual
Trademarks
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or tness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET Industrial 1-Port 802.3at PoE+ to 2-Port 802.3af PoE Extender
User’s Manual
FOR MODEL: IPOE-E202
REVISION: 2.0 (JULY, 2017)
Part No: EM-IPOE-E202_v2.0 (2350-AF0500-002)
Table of Contents
1. Introduction.............................................................................. 5
1.1 Package Contents ............................................................... 5
1.2 How to Use This Manual...................................................... 5
1.3 Product Features................................................................. 5
1.4 Product Specications ......................................................... 8
1.5 Power over Ethernet Budget ...............................................10
1.6 Power over Ethernet Capability ...........................................10
1.6.1 When PSE/PoE Switch Output is DC 52V ....................10
1.6.2 When PSE/PoE Switch Output is DC 56V ....................11
2. Installation ..............................................................................12
2.1 Physical Dimensions ...........................................................12
2.2 Front Panel .......................................................................13
2.3 Rear Panel ........................................................................14
2.4 Mounting Installation..........................................................14
2.4.1 Making Waterproof RJ45 Cable ..................................15
2.4.2 Wall Mounting ..........................................................16
2.4.3 Connecting waterproof RJ45 connector
to the IPOE-E202 .....................................................17
2.5 Connecting IPOE-E202 to Power Source Equipment (PSE) .....19
2.6 Connecting IPOE-E202 to Powered Device (PD) ....................20
3. Customer Support ....................................................................22
APPENDIX A: Networking Connection...............................................23
A.1 Switch’s RJ45 Pin Assignments ............................................23
A.2 RJ45 Cable Pin Assignments................................................24
5
1. Introduction
1.1 Package Contents
Check your package for the following parts:
Industrial PoE Extender x 1
User’s Manual x 1
Waterproof RJ45 Connector x 3
Wall-mounted Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
1.2 How to Use This Manual
This Industrial PoE Extender User Manual is structured as
follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Industrial PoE Extender.
Chapter 3 Customer Support
The chapter explains how to get support from PLANET.
Appendix A
This chapter contains cable information of the Industrial PoE Extender.
1.3 Product Features
Physical Port
3-port 10/100/1000BASE-T Gigabit RJ45 interface
1-port data + power input
2-port data + power output
6
Power over Ethernet
1-port data + power input
Complies with IEEE 802.3at Power over Ethernet Plus end-
span/mid-span PD
Supports PoE input power up to 30.8 watts
2-port data + power output
Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet/
end-span PSE
Up to 2 IEEE 802.3af/802.3at devices powered
Supports PoE power up to 25 watts for each PoE port
Auto detects powered device (PD)
Extends the range of PoE to an additional 100 meters (328ft.)
Forwards both Ethernet data and PoE power to remote device
Layer 2 Features
Hardware based 10/100Mbps, half/full duplex and 1000Mbps full
duplex mode, ow control, auto-negotiation and auto MDI/MDI-X
Features Store-and-Forward mode with wire-speed ltering and
forwarding rates
IEEE 802.3x ow control for full duplex operation and back pres-
sure for half duplex operation
Integrates address look-up engine, supporting 2K absolute MAC
addresses
9K jumbo frame support in 1000Mbps duplex mode
Automatic address learning and address aging
Supports CSMA/CD protocol
7
Industrial Case and Installation
IP63 aluminum case
Wall-mount design
Waterproof and dustproof
Supports EFT protection of 2000 VDC for power line
Supports 2000 VDC Ethernet ESD protection
-40 to 75 degrees C operating temperature
No external power cable required for installation
Plug and Play installation
Standard Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x Flow Control
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3af Power over Ethernet
FCC Part 15 Class A, CE
Note
PSE (Power Sourcing Equipment) is a device (switch
or hub for instance) that provides power in a PoE setup.
Maximum allowed continuous output power per such
device in IEEE 802.3af is 15.4W, and in IEEE 802.3at is
30W.
PDs (Powered Devices) like PoE IP phones, PoE IP
cameras, PoE wireless access points, etc. are PoE-enabled
terminals that consume energy via PSE.
8
1.4 ProductSpecications
Model IPOE-E202
Hardware Specications
Hardware Version 2
Network Connector
PoE In Port
1 x 10/100/1000BASE-T Ethernet with High
PoE “Data + Power” in, auto MDI/MDI-X,
auto-negotiation RJ45 connector
PoE Out Port
2 x 10/100/1000BASE-T Ethernet with IEEE
802.3af/at PoE “Data + Power” out, auto
MDI/MDI-X, auto-negotiation RJ45 connector
Switch Architecture Store-and-Forward switch architecture
MAC Address Table 2K MAC address table with auto learning
function
Data Buffer 1Mbit
Switch Fabric 6Gbps
Switch Throughput 4.46Mpps @ 64 bytes
Flow Control IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 9KB
ESD Protection 2KV DC
EFT Protection 2KV DC
Enclosure IP63 aluminum case
Installation Wall-mount kit
LED Display
System: PWR (Green)
PoE Input Port: LNK/ACT (Orange)
PoE Input Port: 1000 (Orange)
Budget Alert (Green)
Per PoE Output Port: LNK/ACT (Green)
Per PoE Output Port: PoE-in-Use (Orange)
Cable
Twisted-pair cable:
10BASE-T: 2-pair UTP Cat. 3, 4, 5 up to 100
meters
100BASE-TX: 2-pair UTP Cat. 5, 5e up to 100
meters
1000BASE-T: 4-pair UTP Cat. 5e, 6 up to 100
meters
9
Dimensions (W x D x H) 199.6 x 81 x 40 mm
Weight 373g
Power Consumption 30 watts/102.3BTU (Full loading with PoE
function)
Power over Ethernet
PoE Standard
PoE In Port
IEEE 802.3at Power over Ethernet Plus
end-span/mid-span PD class 4 PD
Per PoE Out Port
IEEE 802.3at Power over Ethernet Plus
end-span PSE
IEEE 802.3af Power over Ethernet end-span
PSE
PoE Power
PoE In Port
50~57V DC, max. 30.8 watts
Per PoE Out Port
44~55V DC, max. 25 watts
Power Pin Assignment
PoE In Port
1/2(+), 3/6(-); 4/5(+), 7/8(-)
Per PoE Out Port
1/2(-), 3/6(+)
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (Free fall)
IEC 60068-2-27 (Shock)
IEC 60068-2-6 (Vibration)
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Environment
Operating Temperature: -40 ~ 75 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage Temperature: -40 ~ 85 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
10
1.5 Power over Ethernet Budget
The following table lists how many PoE devices can be powered by
IPOE-E202:
Power Source PoE Output
Budget*
Max. Number of PDs
supported
IEEE 802.3at PoE+
PSE 25 watts max.
Class 4 PD@25
watts 1 unit
Class 3 PD@15
watts 2 units
Class 2 PD@7 watts 2 units
IEEE 802.3af PoE PSE 10 watts max. Class 2 PD@7 watts 1 unit
Remarks
The PoE output budget means the 2-port PD aggre-
gated power output. The aggregated power consump-
tion will be below 30 watts if with PoE+ PSE.
1.6 Power over Ethernet Capability
With different distance and different PoE input source, it will inect the
PoE output capability. Please refer to the table below.
PSE/PoE Switch
PoE Output Capacity
IPOE-E202
(A) (B) (C)
(A): Distance
(B): Distance
(A): Watts
1.6.1 When PSE/PoE Switch Output is DC 52V
A (Distance) B (Distance) C (Watts)
2M 2M 26
2M 20M 25.5
2M 60M 19.6
2M 100M 14.6
Tabla de contenidos
Otros manuales de Extensor de Planet
Planet
Planet IHD-410PT Manual de usuario
Planet
Planet VC-203PT Manual de usuario
Planet
Planet IPOE-E174 Manual de usuario
Planet
Planet WNAP-C3220 Manual de usuario
Planet
Planet WNAP-C3220 Manual de usuario
Planet
Planet VC-205PT Manual de usuario
Planet
Planet LRP-104CET Manual de usuario
Planet
Planet IHD-200PT Manual de usuario
Planet
Planet WBT-1000 Manual de usuario
Planet
Planet LRE-101C Manual de usuario
Planet
Planet LRE-101 Manual de usuario
Planet
Planet POE-E201 Manual de usuario
Planet
Planet IVC-2004PT Manual de usuario
Planet
Planet IVC-2002 Manual de usuario
Planet
Planet IVC-234GT Manual de usuario
Planet
Planet LRP-101CE Manual de usuario
Planet
Planet WRE-1200 Manual de usuario
Planet
Planet WRE-1200 Manual de usuario
Planet
Planet POE-E101 Manual de usuario
Planet
Planet LRP-101C-KIT Manual de usuario
