Philips FlexTune Manual de usuario
June 2021
Tunable White
Systems
Quick Installation Guide
FlexTune Quick Installation Guide
FlexTune
3
Introduction
Philips FlexTune offers a complete, easy-to-install, and future-proof Tunable White System. This Quick Installation Guide explains the basics
and helps you to get up-and-running. For full explanation, several in-detail technical documents can be downloaded from our website (see
page 11)
>
<
4
The FlexTune Building Blocks
A Philips FlexTune System consists of at least three components:
1. A Philips Xitanium FlexTune driver
2. A Tunable White (TW) module, for instance a Philips Fortimo FlexTune module
3. A TW control system, complying to the DALI 209 Standard.
a. Wireless: A TW-compatible node in combination with commissioning app (e.g. Philips EasyAir SNS210 MC
and the Philips field app MC) and a compatible wireless switch
b. Wired: A DALI 209 TW control module
c. Touch & Dim (TD): This feature is based on applying momentary mains voltage by means of two
momentary push buttons to the SR-DA interface. These push buttons can be used to turn on/off and dim
up/down the light (push button 1) and to change the color temperature (push button 2)
To this basic system, additional components such as additional (wireless) switches and various types of sensors can be added. The
number of drivers, modules, and additional components, as well as the complexity of the control system is virtually unlimited, and can
be designed according to your requirements.
Note:
By factory default this SR bus power supply (SR PSU) is enabled, and ready to be used with an external control device. It can be
disabled/re-enabled with MultiOne configuration tools and software.
The driver SR PSU must be disabled in case:
1. The drivers are used in a wired DALI network.
2. The Touch and Dim feature is used.
Note that the SR PSU must be disabled on individual driver level before installation in a system.
<
>
How to build a wireless TW-System
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the node to the driver, this is a two-wire connection to the SR-pins of the driver (see picture below). For the EasyAir
SNS210 MC, plus and minus are interchangeable. For other nodes, check if the plus connection of the node must be
connected to the SR+ pin of the driver.
3. Install the commissioning app, e.g. Philips field app MC.
4. Switch on the system and start the app.
5. Commission the switch (and other components you want to add) with the app.
6. Optionally: Use the app to create Zones and Scenes according to your wishes
5
module
connections
node
connections
Xitanium FlexTune Driver Node
4-wire driver to module
connection
2-wire driver to node
connection
Fortimo FlexTune Module
4-wire driver to module
connection
Cell Phone with
MasterConnect app
Basics of a Wireless TW-System
6
Wireless Switch
How to build a wired TW-System
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the DALI 209 control module to the driver, this is a two-wire connection to the SR-pins of the driver. The plus
connection of the control module must be connected to the SR+ pin of the driver.
Please note: DALI 207 Controls with dual addessing mode are not supported by the FlexTune drivers.
7
module
connections
control module
connections
Xitanium FlexTune Driver
Dali 209 compatible
Control Module
4-wire driver to module
connection
2-wire driver to control
module connection
Fortimo FlexTune Module
Basics of a Wired TW-System
8
How to build a TW-System with Touch & Dim
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the double push button to the driver and mains, according to the diagram on the next page. More details about
Touch & Dim can be found in the Design-in Guide Xitanium SR-drivers (see reference on page 11)
9
module
connections
push button
connections
see next
page
Xitanium FlexTune Driver
Double push button
4-wire driver to module
connection
Fortimo FlexTune Module
Basics of a T&D TW-System
10
Tabla de contenidos
Otros manuales de Equipo de iluminación de Philips
Philips
Philips LEKO LITE Luminaires Manual de instrucciones
Philips
Philips VL440 Spot Manual de usuario
Philips
Philips PLFRESNEL 1 LED LUMINAIRES Manual de instrucciones
Philips
Philips Ecomoods 40339/**/16 Series Manual de usuario
Philips
Philips SL ePAR 180 LED Luminaire Manual de usuario
Philips
Philips 40801 U7 Series Manual de usuario
Philips
Philips BVP525 HGB Manual de usuario
Philips
Philips eW Reach Powercore Manual de usuario
Philips
Philips 17823/**/16 Manual de usuario
Philips
Philips TrueLine RC530B ELP3 Manual de usuario
Philips
Philips TT155 Guía del usuario
Philips
Philips Lightolier EG1-4 Manual de usuario
Philips
Philips 56490-31-16 Manual de usuario
Philips
Philips 32157-31-16 Manual de usuario
Philips
Philips Ledalite Centris Wall Mount Joint 950 Manual de usuario
Philips
Philips Lightolier Lytespan 23C39T4 Manual de usuario
Philips
Philips 56462-48-16 Manual de usuario
Philips
Philips ColorBlast TRX Manual de usuario
Philips
Philips 910503700745 Manual de usuario
Philips
Philips iColor Flex MX gen2 Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
