Philips Bodine Cold-Pak B4CF1 Manual de usuario

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-853-5009 • www.philips.com/bodine

70009410

EMERGENCY LIGHTING EQUIPMENT

Installation Instructions

1. To prevent high voltage from being present on red, yellow & yellow/black output leads prior to installation,

inverter connector must be open. Do not join inverter connector until installation is complete and AC power

is supplied to the emergency ballast.

2. This product is for use with one 13 W through 42 W (4-pin) compact ﬂuorescent lamp without integral starters.

3. Make sure all connections are in accordance with the National Electrical Code, Canadian Electrical Code and

any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter

connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation inside or on top of the ﬁxture.

6. This product is suitable for damp locations where the ambient temperature is -20°C minimum, +55°C

maximum. Product is also suitable for installation in sealed and gasketed ﬁxtures. Product is not suitable

for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld replaceable.

Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

CAUTION: Verify that all replacement lamp types marked on the installed luminaire are also identiﬁed as suitable for

use with this inverter/charger pack.

06/19/17

B4CF1 Cold-Pak

Ni - Cd

INSTALLATION

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED, YELLOW & YELLOW/

BLACK OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN.

DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS

SUPPLIED TO THE EMERGENCY BALLAST.

NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched

source of power is required. The emergency ballast must be fed from the same

branch circuit as the AC ballast.

STEP #1 INSTALLING THE EMERGENCY BALLAST

> Disconnect AC power from the ﬁxture.

> Refer to illustrations below to install emergency ballast. Note: These are only examples of possible installations.

STEP #2 INSTALLING THE TEST SWITCH

> Drill a 1/2" hole and install the test switch (e.g. through

the side of a surface mounted ﬁxture).

> Refer to the illustrations below and wire the test switch so

that it removes AC power from both the emergency ballast

and the AC ballast at the same time.

* For installation on top of the ﬁxture, wire bundle covers (RMC-60) may be required by state or local codes. These covers are available

from the manufacturer as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete

information.

Inside Ballast Channel

INSIDE BALLAST CHANNEL INSIDE THE FIXTURE Inside Strip Fixture

ON TOP OF FIXTURE

UNSWITCHED FIXTURE

SWITCHED FIXTURE

BLACK

WHITE

HOT

COM

TEST

SWITCH

WALL

SWITCH

BALLAST

BLACK

EMERGENCY

BALLAST

WHITE

WHT/BLK

HOT

COM

TEST

SWITCH

BALLAST

WHT/RED

WHITE

BLACK 120V

ORANGE 277V

EMERGENCY

BALLAST

WHT/BLK

WHT/RED

WHITE

BLACK 120V

ORANGE 277V

Fixture

Test Button

Hex Nut

Test Switch

Leads

Push to Test

When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When

power fails, the emergency ballast automatically switches to emergency power (internal battery), operating one lamp at

reduced illumination. This emergency ballast will operate one 13 W through 42 W lamp for a minimum of 90 minutes. When

AC power is restored, the normal ballast operation is delayed by approximately three (3) seconds to prevent false tripping

of AC ballast (end-of-lamp-life) shutdown circuit. The temperature control circuitry assures the proper charging current and

battery protection under the full allowable ambient temperature range.

Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to

ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One lamp should

operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced illumination for at least

90 minutes.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

OPERATION

STEP #4 WIRING THE EMERGENCY BALLAST

> Determine the type of AC ballast installed in the ﬁxture.

> Select the appropriate wiring diagram on back to connect the emergency ballast to the AC ballast and lamp(s).

Make electrical connections in accordance with the National Electrical Code, Canadian Electrical Code and any local

regulations.

> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.

> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging

Indicator Light should illuminate indicating the battery is charging.

> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge

for 24 hours before conducting a long-term discharge test. Refer to OPERATION.

> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point.

To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency

Power Supplies Before Servicing."

MAINTENANCE

STEP #3 INSTALLING THE CHARGING INDICATOR LIGHT

> Install the CHARGING INDICATOR LIGHT as shown in the illustration below so that it will be visible after the

ﬁxture is installed.

NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label.

Charging

Indicator

Light

1/2" White

Bushing

Violet (+)

Brown (–)

Violet (+)

Brown (–)

1/2" White

Bushing

5/8" Black

Bushing

5/8" Black

Bushing

1/2" Punch

Fixture Fixture

Charging

Indicator

Light

FIG G. ONE (1) 4-PIN COMPACT LAMP RAPID START BALLAST

WIRING DIAGRAM for Emergency-Only ﬁxtures

WIRING DIAGRAMS for 1-LAMP emergency operation

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

IMPORTANT: REFER TO TABLE 1 REGARDING BROWN CONNECTOR

RAPID START AC BALLASTS

1 LAMP

RAPID START

BALLAST

BLUE

BROWN

RED

YELLOW

YEL/BLK

BLU/WHT

BLUE

RED

LAMP 1

WARNING: Refer to Table 1 before connecting

BLACK

WHITE

BLK

TEST

SWITCH

COM BLK

WHT/BLK

WHITE

WALL SWITCH

WHT/RED

RED

WHITE

VIOLET (+)

BROWN (-)

(CAP UNUSED LEAD) BLACK 120V

ORANGE 277V

INVERTER

CONNECTOR

CHARGING

INDICATOR

HOT

FIG H. TWO (2) 4-PIN COMPACT LAMP RAPID START BALLAST

2 LAMP

RAPID START

BALLAST

BLUE

BROWN

RED

YELLOW

YEL/BLK

BLU/WHT

BLUE

YELLOW

RED

LAMP 1

LAMP 2

WARNING: Refer to Table 1 before connecting

EMERGENCY

BLACK

WHITE

BLK

TEST

SWITCH

COM BLK

WHT/BLK

WHITE

WALL SWITCH

WHT/RED

RED

WHITE

VIOLET (+)

BROWN (-)

(CAP UNUSED LEAD) BLACK 120V

ORANGE 277V

INVERTER

CONNECTOR

CHARGING

INDICATOR

HOT

FIG I. ONE (1) 4-PIN COMPACT LAMP WITHOUT AC BALLAST(13 W-42 W)

BROWN

RED

YELLOW

YEL/BLK

BLU/WHT

BLUE

(CAP)

LAMP

WHT/RED

RED

WHITE

VIOLET (+)

BROWN (-)

WHITE

WHT/BLK

COMMON

HOT

(CAP UNUSED LEAD)

(CAP)

BLACK 120V

ORANGE 277V

TEST

SWITCH

INVERTER

CONNECTOR

CHARGING

INDICATOR

WARNING: Refer to Table 1 before connecting

TABLE 1

LAMP

POWER

BROWN

CONNECTOR

13 - 23 W CLOSED

24 - 42 W OPEN

Tabla de contenidos

Otros manuales de Equipo de iluminación de Philips

Philips

Philips hue Manual de usuario

Philips

Philips ColorBlast TRX Manual de usuario

Philips

Philips Ligholier KUBIK 1.0 SL110A Manual de usuario

Philips

Philips 57949-17-16 Manual de usuario

Philips

Philips HF3532 Manual de usuario

Philips

Philips Value-plus LCM310 Manual de usuario

Philips

Philips burton SUPER EXAM 50 LED Hoja de especificaciones

Philips

Philips VL3015 Spot Luminaire Manual de usuario

Philips

Philips TrueLine RC530B ELP3 Manual de usuario

Philips

Philips 56454-17-16 Manual de usuario

Philips

Philips 17823/**/16 Manual de usuario

Philips

Philips DN027B Guía del usuario

Philips

Philips 69055/**/16 Manual de usuario

Philips

Philips DayLight 8 Manual de usuario

Philips

Philips 31608-48-16 Manual de usuario

Philips

Philips MASTER Colour CDM-T 250W Manual de usuario

Philips

Philips hue Flourish Manual de usuario

Philips

Philips BVP528 Manual de usuario

Philips

Philips 56459-17-16 Manual de usuario

Philips

Philips HF3671/01 Manual de usuario

Philips

Philips L 1250 - HPM Instrucciones de funcionamiento y mantenimiento

Philips

Philips Lightolier Lytespan 23C39T4 Manual de usuario

Philips

Philips TWS101 Manual de usuario

Philips

Philips RC095V Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario