Philips PLFRESNEL1 Manual de usuario

SF PLFresnel1 –December 2012 pg1 of 4

SHORT FORM OPERATION MANUAL

PLFRESNEL1 LED LUMINAIRE

THANK YOU FOR PURCHASING A PHILIPS SELECON PLFRESNEL1 LED

LUMINAIRE. WE HAVE DESIGNED THIS LUMINAIRE TO PROVIDE YOU WITH A

SUPERIOR FITTING IN PERFORMANCE, DESIGN AND ENGINEERING. WE ARE

CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR MANY

YEARS TO COME.

Caution! Installation is entirely at your risk. Do not attempt installation unless you are suitably qualified. If you do

not understand a point in this manual, don’t guess. Don’t take short cuts. If in doubt, stop! Contact Philips Selecon

or one of its authorised distributors for advice. Don’t be afraid to ask for help.

This SHORT FORM MANUAL is designed to provide you with the information that you will need IMMEDIATELY upon

unpacking your new luminaire. This manual covers information required for the PLFR1-03 products.

We recommend making a note of the serial numbers of your purchased luminaires for future reference.

(The serial number can be found on the sticker on the side of the yoke on the unit and on the outside of the box the unit was packed in).

Important Note: Before discarding the packaging ensure you have the suspension bolt set

Electrical Installation

WARNING!!! Risk of fire and electric shock. This product is to be installed by a qualified electrician only. Ensure that the AC

power is switched off before attempting to make any wiring connections.

This fixture employs a grounded type receptacle and is not intended for connection to a two-wire, ungrounded source of supply.

To avoid the chance of product damage or malfunction, disconnect power before connecting wires, and do not connect or

disconnect cables (supply, data, lamps and interface cables) when voltage is supplied to the luminaire.

Mains Voltage: 100-240VAC (+/- 10%). unit must be direct switching mains only, not via a dimmer system.

When installing this fixture use wire conductor colour codes as follows:

Brown - Phase, live

Blue - Neutral, return

Green/Yellow - Earth, ground

Mounting

A safety bond MUST always be used when rigging luminaires on bars, trusses, etc. The safety bond is fixed to the luminaire

lamp-house anchor point, located at the rear of the luminaire, and is wrapped around the bar and attached to itself. This is the

only recommended anchor point for the luminaire. Philips Selecon supplies a fitted safety bond with all theatrical / entertainment

luminaires.

Ambient Operating Temperature: 0°C to 40°C

To guarantee product lifetime, the user should ensure that the ambient temperature remains within the recommended

temperature range.

Philips Selecon has packaged this product using environmentally friendly packaging. Please consider

either reuse of the packaging or dispose of responsibly with your nearest recycling collection agency.

Adjusting the tilt angle

Loosen the lock off handle on the side of the

luminaire, tilt and retighten finger tight

Focus

Loosen the focus knob on the bottom of the fixture,

gently slide engine forward for flood and backwards

for spot, tighten focus knob once focused.

Yoke Adjustment

Loosen the fasteners on either side of the yoke,

reposition yoke, tighten fasteners. Ensure yoke is

aligned correctly before tightening fasteners again.

SF PLFresnel1 –December 2012 pg2 of 4

Operation and Programming

MAIN MENU (scrolling up or down from the splash screen)

LCD Display

Displays all menu parameters and

option settings. Also displays

DMX512 address.

Preset Button

Allows the recall of stored presets

Intensity Button

Allows the customisation of current

intensity (light output). Note, using

the LEFT and RIGHT arrow

buttons you can select each

RGBW channel individually and

using the UP and DOWN arrows

change their intensity.

OK (Enter) Button

Accesses details, activates a field, or

enters a setting depending on the

current menu item

Up/Down/Left/Right

Arrow Buttons

Navigates menu system and used for

selecting and setting options.

Escape Button

Enters menu options. Navigates

(backs up) one menu level.

SF PLFresnel1 –December 2012 pg3 of 4

MAIN MENU CONTINUED:

Settings available for editing are dependent on the current security

level. These include General, Presets, DMX, Fan and Display

Unwanted changes to a

luminaire‟s settings can be locked.

(see „security‟ on pg4)

SF PLFresnel1 –December 2012 pg4 of 4

Main Menu (if scrolling left or right from the main splash screen)

DMX Address (if fixture is unlocked, hit „OK‟ to change DMX address)

Fixture Hours (displays fixture operating hours since last reset)

Fixture Power (displays Max Power Limit setting, in Watts, Present Power consumed by fixture, in Watts, and Hrs of use)

Fixtures Status (displays current operational temperature, LED status, and fan speed setting)

Control

The PLFresnel1 can be controlled using DMX protocol. Units are fitted with XLR5 in/out connectors.

Basic DMX512 installation consists of connecting multiple luminaires together (up to 32 luminaires) in „daisy-chain‟ fashion. A

cable runs from the DMX512 control source to the DMX connector on the first luminaire. Another cable is then connected from

the first luminaire to a dmx connector on the next luminaire, or device to be controlled, and so on.

DMX Addressing

The default address for the PLFresnel1 is “001”.

The individual luminaire DMX address can be set by scrolling left or right from the main menu screen and selecting „OK‟ when on

the DMX Address Status Screen. The unit requires between 3 to 15 DMX channels, depending on the DMX mode.

DMX Channel

Parameter

16-bit Mode

8-bit Mode

3-Channel Mode

Intensity –High

Intensity

Intensity –Low

Red

Preset Colour Selection

Red –High Byte

Green

Timing

Red –Low Byte

Blue

Green –High Byte

White

Green –Low Byte

Preset Colour Selection

Blue –High Byte

Not used (for future use)

Blue –Low Byte

Timing

White –High Byte

Control

White –Low byte

Preset Colour Selection

Not used (for future use)

Intensity Time

Colour Time

Control

Security

In the settings menu each feature (General, Presets, DMX, Fan Display) can be locked to prevent tampering.

A 4-digit password can be set for each of three different levels of security, within the settings menu, when in security level 3.

The fixture can be locked by scrolling to „Lock Fixture‟ in the menu and choosing „Yes‟ when asked if you want to lock the fixture.

To unlock the fixture the chosen password will be required.

Service and Maintenance

Philips Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international

safety standards. It is your responsibility to maintain this luminaire in good and safe working condition. Repairs should only be

carried out by suitably qualified persons. Do not operate the luminaire with cracked body, damaged cable etc. Consult your

Philips Selecon distributor for assistance. Only replace damaged parts with authorised Philips spares.

Being a solid-state fixture the PLFresnel1 requires very little routine maintenance by the user.

LIMITED 3-YEAR WARRANTY

Philips Selecon warrants its luminaires against defects in materials or workmanship. The term of this warranty is based

on the product usage and is from the date of delivery. Entertainment, Theatre relates to the typical conditions found in

a theatre performance venue viz: 4 –6 hrs per day, six days per week.

WARRANTY REGISTRATION: www.seleconlight.com/warrantyreg

Take full advantage of the Philips Selecon service commitment and register all your new Philips Selecon luminaires quickly

and easily online for full after-sales support.

If you require further assistance please contact your Philips Selecon dealer: www.seleconlight.com/distributors

These luminaires are not suitable

for outdoor use. They do not have

an IP rating.

Otros manuales de Equipo de iluminación de Philips

Philips

Philips ELC/10H Long Life Manual de usuario

Philips

Philips GreenPower LED production module DR/B Manual de usuario

Philips

Philips Bodine B94G Type 2 Manual de usuario

Philips

Philips Lightolier Solution Series Manual de usuario

Philips

Philips VU6 Instrucciones de instalación

Philips

Philips 40801 U7 Series Manual de usuario

Philips

Philips 300S Manual de usuario

Philips

Philips RCH20 Manual de usuario

Philips

Philips 56420-31-16 Manual de usuario

Philips

Philips 100LT Manual de usuario

Philips

Philips B50ST Manual de usuario

Philips

Philips Softone 871150066257610 Manual de usuario

Philips

Philips TrueLine SM530C Manual de usuario

Philips

Philips 78201 U7 Series Manual de usuario

Philips

Philips 30504 Manual de usuario

Philips

Philips Ecomoods 16902/**/16 Manual de usuario

Philips

Philips CertaFlux RDL Vertical Manual de usuario

Philips

Philips 56422-31-16 Manual de usuario

Philips

Philips bodine LP400 Manual de usuario

Philips

Philips 59273-17-16 Manual de usuario

Philips

Philips dynalite Manual de usuario

Philips

Philips SC Series Manual de usuario

Philips

Philips Vari-Lite Manual de usuario

Philips

Philips Lightstrip Plus 71901/U8 Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario