Perlesmith PSLTK1 Manual de usuario
Model : PSLTK1
Tilting TV Wall Mount
Instruction Manual
For any parts enquiries, please contact AV Supply Group as below:
IMPORTANT SAFETY INFORMATION
Check the VESA Pattern of TV before the Installation
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete
block and brick walls. - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
100mm ≈ 3.9”
200mm ≈ 7.9”
600mm ≈ 23.6”
400mm ≈ 15.7”
Minimum VESA pattern: 200mm / 7.9” (W) x 100mm / 3.9” (H)
If your TV VESA is greater than 600 x 400mm / 23.6 x 15.7” or less
than VESA 200 x 100mm / 7.9 x 3.9”, this mount is NOT compatible.
Weight Restrictions
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
within the maximum weights indicated. Use with
products heavier than the maximum weights
indicated may result in failure of the mount and
its accessories, causing damage and or injury.
If your TV weighs more, this
mount is NOT compatible.
132 lbs /
60 kg
WARNING
MAX: 600mm / 23.6”
MAX: 400mm / 15.7”
01 05 07 09
Awl
Stud Finder
Tape Measure Pencil Drill
7/32'' (5.5mm)
Wood Drill Bit
3/8'' (10mm)
Concrete Drill Bit
1/2'' (13mm)
Socket Wrench
Phillips
Screwdriver
Hammer
OR
(Tools Needed for Wood Stud Installation) (Tools Needed for Solid Concrete,
Concrete Block and Brick Wall Installation)
Tools Needed (Not lncluded)
Verify Your Wall Construction
If you are not sure of the
wall construction, please
contact our customer
service at
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
contact our customer service at [email protected].
•PLEASE NOTE: Not all hardware included in this package will be used.
Left TV Bracket
x 1
03
Right TV Bracket
x 1
04
5/16” (8mm)
Wrench
02 05 07 09
Right Wall Plate x 1
01
Left Wall Plate x 1
02 08
x 1
Level
Supplied Parts and Hardware for Step 2 and 3
Spacers
[if needed]
06
[F1] x 8
L2.5mm
[F2] x 4
L10mm
[F3] x 4
L22mm
NOTE: The spacers shown are actual size.
Washers
05
M4 / M5
[B1] x 4
M6 / M8
[B2] x 4
TV Bolts
[Only one size of the bolt fits your TV]
07
NOTE: The bolts shown are actual size.
M6
M4
M8
M4 x 12mm
[C1] x 4
M6 x 15mm
[D1] x 4
M8 x 35mm
[E2] x 4
M8 x 15mm
[E1] x 4
M8 x 50mm
[E3] x 4
M6 x 35mm
[D2] x 4
M4 x 30mm
[C2] x 4
03 05 07 09
Only one size of the fits your TV.
Step 1 Secure the TV Brackets [03] and [04] to TV
Select TV Bolts
BOLT LENGTH: Verify adequate thread engagement with bolts or bolts /
spacers combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
PLEASE NOTE: The provided TV bolts meet most of today’s TVs design.
However, some TVs require special bolts which may NOT be in the hardware
bag. In this case, we offer our “PSUHP" Universal Hardware Kit which
provides a large selection of bolts that can meet the demand of older and
unique applications.
IMPORTANT: When using the spacers, it is important to note that they can be
used in multi-layers (meaning stacked). If you have any difficulty undestand-
ing how to install the TV bolts or spacers, please contact customer service at
Too Long
Correct Correct
Too Short
M4 M6 M8
NOTE: The lag screw shown is actual size.
x 4
A1
x 4
Wall
Anchor
Lag Screw
ST5/16 x 2-3/4"
This anchor is for con-
crete or brick walls
ONLY. DO NOT use them in
drywall or wood studs.
CAUTION!
φ10mm
A2
04 05 07 09
04
03
04 03
PLEASE NOTE: The bolt hole
locations on your TV may vary in
accordance of the manufacturer's
design of the TV. We are only illustrating
possible locations of the bolt holes.
CAUTION: When attaching the TV
brackets [03] and [04] to the back of the
TV, ensure the ends with round holes on
the TV brackets are pointing to the top of
the TV and are equally centered on the
back of the TV.
Option B (For Round Back TV)
Option A (For Flat Back TV)
UP
Alternate
Spacer
Setups
Alternate Spacer
Setups
05 B1 / B2
07 C1 / D1 / E1
(If Needed)
06 F1 / F2
04
03
05 B1 / B2
07 C2 / D2 / E2 / E3
06 F1 / F2 / F3
05 07 09
Option C (For TV with A “Bump”)
Alternate Spacer
Setups
04
03
Alternate Spacer
Setups
Option D
04
For cable interference or inset holes, use spacers [06] to create extra
space between the TV and TV brackets.
04
05 B1 / B2
07 C2 / D2 / E2 / E3
06 F1 / F2 / F3
05 B1 / B2
07 C2 / D2 / E2 / E3
06 F1 / F2 / F3
05 06 07 09
● Avoid potential personal injury or property damage! Do not use a drill for
tightening the lag screws! Only use a socket wrench. DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against
the wall plate [01] and [02].
●DO NOT USE THE ANCHOR [A2] FOR THIS STEP!
● Ensure the wall plate [01] and [02] is securely fastened to the wall
before continuing to the next step.
● Any material covering the wall must not exceed 5/8” (16mm).
● Nominal wood stud size: common 2 x 4” (51 x 102mm)
minimum 1 1/2 x 3 1/2” (38 x 89mm).
● Stud center must be verified.
A2
X
Phillips Screwdriver
(NOT lncluded)
Step 2 Assemble the Wall Plate [01] and [02]
2-1 Loosen 4 preassembled bolts [S1] using Phillips screwdriver and keep
for the use in 2-2.
2-2 Secure the right wall plate [01] to the left wall plate [02] by tightening
the bolts [S1].
Tighten
Loosen
S1
2-1
2-2
DO NOT overtighten.
Tighten only until snug.
Step 3 Attach the Wall Plate [01] and [02] to Wall
For wood stud installation, follow STEP 3A.
For concrete installation, follow STEP 3B.
Step 3A Wood Stud Option
WARNING:
05 07 09
02
01
3A-1
3A-2
Position the wall plate [01] and [02]
at your desired height and line up
the holes with your stud center line.
Level the wall plate [01] and [02]
and mark the holes.
24” (610mm)
16
” (
406mm)
Use a stud finder (NOT included) to
locate wood studs or use an awl
(NOT included) to verify the edges.
Mark the edge and center locations.
Awl
(NOT lncluded) Stud Finder
(NOT lncluded)
OR
OR
3A-3
ø7/32
”
(5.5mm)
2 3/4
”
(70mm)
Drill 4 pilot holes using a 7/32
”
(
5.5mm) diameter drill bit. Make
sure the depth is NOT less than 2
3/4
” (
70mm).
Drill
(NOT lncluded)
Pencil
(NOT lncluded)
05 07 08 09
02
01
3A-4
Step 3B Solid Concrete or Concrete Block Option
3B-1
WARNING:
●Avoid potential personal injury or property damage! Do not use a drill for
tightening the lag screws! Only use a socket wrench. DO NOT over-tighten
the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled
firmly against the wall plate [01] and [02].
● Ensure the wall plate [01] and [02] is securely fastened to the
wall before continuing to the next step.
● Mount the wall plate [01] and [02] directly onto the concrete surface.
● Anything covering the wall must not exceed 5/8” (16mm).
● Minimum solid concrete thickness: 8” (203mm).
● Minimum concrete block size: 8 x 8 x 16” (203 x 203 x 406mm).
● Never drill into the mortar between blocks.
Install the wall plate [01] and
[02] using lag screws [A1].
Tighten the lag screws [A1]
only until they are pulled firmly
against the wall plate [01] and
[02]. Do not over-tighten the
lag screws [A1].
1/2
”
(13mm)
Socket Wrench
(NOT lncluded)
02
01
A1
A2
Position the wall plate [01] and
[02] at your desired height, level
the wall plate [01] and [02] and
mark the pilot hole locations.
Pencil
(NOT lncluded)
05 07 09
Tabla de contenidos
Otros manuales de Soporte de TV de Perlesmith
Perlesmith
Perlesmith PSSL1 Manual de usuario
Perlesmith
Perlesmith PSLFK3-24 Manual de usuario
Perlesmith
Perlesmith PSTVS02 Manual de usuario
Perlesmith
Perlesmith PSCM2 Manual de usuario
Perlesmith
Perlesmith PSXFK2 Manual de usuario
Perlesmith
Perlesmith PSXF3 Manual de usuario
Perlesmith
Perlesmith PSLLK1 Manual de usuario
Perlesmith
Perlesmith PSTM1 Manual de usuario
Perlesmith
Perlesmith PSLFK1-24 Manual de usuario
Perlesmith
Perlesmith PSCMF1 Manual de usuario
Perlesmith
Perlesmith PSLF4 Manual de usuario
Perlesmith
Perlesmith PSLTK2 Manual de usuario
Perlesmith
Perlesmith PSTVS01 Manual de usuario
Perlesmith
Perlesmith PSTVS04 Manual de usuario
Perlesmith
Perlesmith PSXFK1 Manual de usuario
Perlesmith
Perlesmith PSLFK3 Manual de usuario
Perlesmith
Perlesmith PSTVS21 Manual de usuario
Perlesmith
Perlesmith PSTVS09 Manual de usuario
Perlesmith
Perlesmith PSMFK1 Manual de usuario
Perlesmith
Perlesmith PSLF6 Manual de usuario
